Mass transfer in polycrystalline ytterbium monosilicate under oxygen potential gradients at high temperatures

Mass transfer in polycrystalline Yb₂SiO₅ wafers with precise composition control was evaluated and analyzed by oxygen permeation experiments at high temperatures using an oxygen tracer. Oxygen permeation proceeded due to mutual grain boundary diffusion of oxide ions and Yb ions without synergistic effects such as acceleration or suppression. The oxygen shielding properties of Yb₂SiO₅ were compared with those of the other line compounds such as Yb₂Si₂O₇ and Al₂O₃ based on the determined mass transfer parameters. It was found that the more preferentially an oxide ion diffuses in the grain boundary compared to the interior of the grain, the greater the effect of suppressing the movement of the oxide ion by applying an oxygen potential gradient becomes.     

Vapor absorption by LiBr aqueous solution in vertical smooth tubes

Heat and mass transfer in a falling film vertical in-tube absorber was studied experimentally with LiBr aqueous solution. The presented results include the effect of solution flow rate, solution subcooling and cooling water temperature on the absorption in a smooth copper tube 16.05 mm I.D. and 400 mm long. The experimental data in the previous report for a 1200-mm-long tube was also re-examined and compared. It was demonstrated by the observation of the flow in the tube that the break down of the liquid film into rivulets leads to deterioration of heat and mass transfer at lower film Reynolds number or in longer tubes. An attempt to evaluate physically acceptable heat and mass transfer coefficients that are defined with estimated temperature and concentration at the vapor–liquid interface was also presented.     

Transmittance and cathodoluminescence of AlN ceramics sintered with Ca3Al2O6 as sintering additive

Aluminum nitride ceramics were prepared by sintering with 0–4.8 mass% of Ca₃Al₂O₆ (C₃A) as a sintering additive. The transmittance in the range of 260–550 nm increased with increasing amount of C₃A. The cathodoluminescence intensity attributed to oxygen-induced defects decreased with increasing amount of C₃A. From the results, the increase of the transmittance in the range of 260–550 nm was considered to be related to the decrease of the oxygen-induced defect density.     

Markedly compressible behaviors of gellan hydrogels in a constrained geometry at ultraslow strain rates

The fracture behaviors of gellan hydrogels under compression remarkably depend on the strain rate as well as the boundary conditions for lateral expansion. In the geometry with no constraint for lateral expansion (conventional uniaxial compression), the gels rupture at relatively small strains independently of the compression rates. In contrast, when the gels are compressed extremely slowly (at a strain rate of ca. 10⁻⁵ s⁻¹) in the geometry prohibiting the lateral expansion at their top and bottom surfaces, they are remarkably compressible down to 2% of the initial height without macroscopic fracture and they are accompanied by a large amount of water release. In such markedly compressed gels, many microscopic cracks are formed around the central layer, where strain concentration occurs due to the nonuniform deformation arising from the constrained geometry. In the highly compressible case, the formation of macroscopic cracks is prevented by the localization of microscopic cracks as well as the enhancement in mechanical toughness by a significant increase in polymer concentration due to water release.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

Performance prediction of a hybrid‐excitation synchronous machine with axially arranged excitation poles and permanent‐magnet poles

This paper presents a method of predicting the steady‐state performance of a new hybrid‐excitation synchronous machine (HESM) theoretically. The field pole of this HESM is axially divided into two parts; one is an excitation part and the other a permanent‐magnet (PM) part. A nonlinear equivalent circuit, which can include the saliency of the rotor and the magnetic saturation due to the iron core, is derived. Based on this equivalent circuit, the steady‐state performance of the HESM is calculated, and the results are confirmed through experiments. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(2): 43–49, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20033     

Assessment of improvement of myocardial fatty acid uptake and function after revascularization using iodine-123-BMIPP

We investigated the effect of bioflavonoid quercetin on tyrosine phosphorylation and phospholipase D (PLD, EC 3.1.4.4) activation in rabbit peritoneal neutrophils stimulated by N-formylmethionyl-leucyl-phenylalanine (fMLP). The quercetin dose-dependently inhibited degranulation and superoxide production in fMLP-stimulated neutrophils. A strong inhibitory effect of quercetin on the tyrosine phosphorylation of several proteins (40, 42, 43, 45, 46 and 75 kDa) was observed when the neutrophils were pretreated with different concentrations of quercetin. Furthermore, quercetin inhibited mitogen activated protein kinase (MAP kinase) and PLD activation induced by fMLP in a dose-dependent manner. The reduction in PLD activity was 30% at 0.1 microM and 70% at 100 microM of quercetin. These results suggest that impairment of neutrophil functions by quercetin may be due, at least in part, to inhibition of tyrosine phosphorylation and PLD activation.     

Tissue compatibility of polylactic acids in the skeletal site

This study was undertaken to examine the osseous tissue compatibility of polylactic acid (PLA) with properties of bioabsorbability and plasticity. Two kinds of granular PLA with different molecular weight (PLA-H: 28 000 MW, PLA-L: 10 600 MW) were implanted into rat tibiae and light microscopic sections were prepared at 1, 2, 4, 8, 16, and 24 weeks following surgery. The tissue compatibility of the PLAs was compared with that of hydroxyapatite (HAP) which is a non-absorbable biocompatible material. After implantation, both PLAs were gradually absorbed and replaced by marrow tissue at 24 weeks. PLA-H degraded slower than PLA-L. New bone formation was observed around each PLA by 4 weeks, and a vast amount of bone deposited on PLA-H at 16 weeks. Phagocytic reactions to the PLAs were noted, however, severe inflammation was not seen. HAP was not absorbed and bone surrounded it throughout the experiment. These results indicate good tissue compatibility of PLA as a bioabsorbable material at the skeletal site.