Ultrafast Electron–Phonon Coupling at Metal-Dielectric Interface

Energy transfer from photo-excited electrons in a metal thin film to the dielectric substrate is important for understanding the ultrafast heat transfer process across the two materials. Substantial research has been conducted to investigate heat transfer in a metal-dielectric structure. In this work, a two-temperature model in metal was used to analyze the interface electron and dielectric substrate coupling. An improved temperature and wavelength-dependent Drude–Lorentz model was implemented to interpret the signals obtained in optical measurements. Ultrafast pump-and-probe measurements on Au-Si samples were carried out, where the probe photon energy was chosen to be close to the interband transition threshold of gold to minimize the influence of non-equilibrium electrons on the optical response and maximize the thermal modulation to the optical reflectance. Electron-substrate interface thermal conductance at different pump laser fluences was obtained, and was found to increase with the interface temperature.     

Deposition of thin film silicon using the pulsed PECVD and HWCVD techniques

We report on the use of pulsed plasma-enhanced chemical vapor deposition (P-PECVD) technique and show that “state-of-the-art” amorphous silicon (a-Si:H) materials and solar cells can be produced at a deposition rate of up to 15 Å/s using a modulation frequency in the range 1–100 kHz. The approach has also been developed to deposit materials and devices onto large area, 30 cm×40 cm, substrates with thickness uniformity (<5%), and gas utilization rate (>25%). We have developed a new “hot wire” chemical vapor deposition (HWCVD) method and report that our new filament material, graphite, has so far shown no appreciable degradation even after deposition of 500 μm of amorphous silicon. We report that this technique can produce “state-of-the-art” a-Si:H and that a solar cell of p/i/n configuration exhibited an initial efficiency approaching 9%. The use of microcrystalline silicon (μc-Si) materials to produce low-cost stable solar cells is gaining considerable attention. We show that both of these techniques can produce thin film μc-Si, dependent on process conditions, with 1 1 1 and/or 2 2 0 orientations and with a grain size of approx. 500 A. Inclusion of these types of materials into a solar cell configuration will be discussed.     

Resource contention in shared-memory multiprocessors: A parameterized performance degradation model

A standard metric conventionally employed to compare the performance of different multiprocessor systems is speedup. Although providing a measure of the improvement in execution speed achievable on a system, this metric does not yield any insight into the factors responsible for limiting the potential improvement in speed. This paper studies the performance degradation in shared-memory multiprocessors as a result of contention for shared-memory resources. A replicate workload framework with a flexible mechanism for workload specification is proposed for measuring performance. Two normalized performance metrics—efficiency and overhead factor—are introduced to quantify the factors limiting performance and facilitate comparison across architectures. Finally, the proposed model is employed to measure and compare the performance of three contemporary shared-memory systems, with special emphasis on the newly released BBN Butterfly-II (TC2000), currently undergoing Beta test.     

INFLUENCE OF DRYING CONDITIONS ON THE FRAGILITY OF CORN KERNELS

A dynamic rcsring dnim war built to study the effects of air temperature, moisture content and grain shape on fragility of the air dried kernels. For drying rares under 0.05 kglkg min. the fragility of kernels could br described empirically as a function of the three experimental parameters.     

STEAM DRYING TECHNOLOGIES: JAPANESE R&D

This report reviews some fundamental and practical aspects of steam drying technologies based mainly on studies published in Japan. Steam drying kinetics, and some industrial technologies particularly for drying of foods, textiles and sludges are reviewed with focus on quality of dried material, drying time, dryer selection and energy recovery from steam dryer exhaust. For energy recovery, heat pump technologies are outlined along with characteristics of different types of steam compressors. A new process is proposed for steam drying; it combines a direct-indirect dryer followed by a direct steam dryer for internal moisture removal.     

CATALYTIC CRACKING OF TARS FROM COAL DEVOLATILIZATION

A set of runs were performed on the catalytic and thermal cracking of the tars present fn the gasifier off-gas stream; the cracking referred to here Js essentially hydrocracking, in view of the considerable amount of hydrogen being present in the gas stream. The catalyst evaluated for tar cracking was a commercial cobalt-molybdenum catalyst, suppported on γ-Al₂O₃(Katalco-477). It was observed that there was a decrease in the amount of tar obtained with the cracking unit on-line with the gasifier; the tars were cracked to gaseous products in the presence of catalyst. Furthermore, it appeared that higher ring structures were transformed to less heavier components; thus cracking could become beneficial in downstream processing of the gas stream coming out of a gasifier.