Quantitative risk assessment using a Japanese hydrogen refueling station model

Although hydrogen refueling stations (HRSs) are becoming widespread across Japan and are essential for the operation of fuel cell vehicles, they present potential hazards. A large number of accidents such as explosions or fires have been reported, rendering it necessary to conduct a number of qualitative and quantitative risk assessments for HRSs. Current safety codes and technical standards related to Japanese HRSs have been established based on the results of a qualitative risk assessment and quantitative effectiveness validation of safety measures over ten years ago. In the last decade, there has been much development in the technologies of the components or facilities used in domestic HRSs and much operational experience as well as knowledge to use hydrogen in HRSs safely have been gained through years of commercial operation. The purpose of the present study is to conduct a quantitative risk assessment (QRA) of the latest HRS model representing Japanese HRSs with the most current information and to identify the most significant scenarios that pose the greatest risks to the physical surroundings in the HRS model. The results of the QRA show that the risk contours of 10^?3 and 10^?4 per year were confined within the HRS boundaries, whereas the risk contours of 10^?5 and 10^?6 per year are still present outside the HRS. Comparing the breakdown of the individual risks (IRs) at the risk ranking points, we conclude that the risk of jet fire demonstrates the highest contribution to the risks at all of the risk ranking points and outside the station. To reduce these risks and confine the risk contour of 10^?6 per year within the HRS boundaries, it is necessary to consider risk mitigation measures for jet fires.     

The method of double averaging: an approach for modeling power-factor-correction switching converters

This paper describes the modeling of power-factor-correction converters under average-current-mode control, which are widely used in switch-mode power supply applications. The objective is to identify stability boundaries in terms of major circuit parameters for facilitating design of such converters. The approach employs a double averaging procedure, which first applies the usual averaging over the switching period and subsequently applies generalized averaging over the mains period. The resulting model, after two averaging steps and application of a harmonic balance procedure, is nonlinear and capable of describing the low-frequency nonlinear dynamics of the system. The parameter ranges within which stable operation is guaranteed can be accurately and easily found using this model. Experimental measurements are provided for verification of the analytical results.     

Synthesis and photosensitivity of acryloylmorpholine copolymers with a pendant (meth)acryloyl group

We have developed new photopolymers that have superior waterproof properties and that can easily interact with polyfunctional acrylate compounds, thus serving as hydrophobic photocrosslinking reagents. Acryloylmorpholine monomers whose homopolymers were less moisture absorbing than the usual water‐soluble polymers but were still water soluble to a good degree, were copolymerized with other acryloyl monomers. We then introduced the photosensitive (meth)acryloyl group to side chains of the resulting polymers. Among six copolymers examined, the copolymers composed of acryloyl morpholine, hydroxyethyl acrylate, ethyl, or methyl methacrylate, and methacryloyl isocyanate were found to have nicely balanced hydrophilicity and waterproof properties, in addition to good compatibility with hydrophobic photocrosslinking reagents. The composite polymers thus obtained were confirmed to be promising photopolymers usable even in a highly humid environment. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 684–692, 2003     

Theoretical model for flash generation

Reduction of flash generated in a gas vent is of great concern for manufacturers of electronic parts. The present study proposes a theoretical model for flash generation through consideration of flow characteristics in a gas vent. The model predicts the factors controlling flash, i.e., material parameters such as zero‐shear viscosity, crystallization temperature, thermal conductivity, and heat capacity, and process parameters such as injection and mold wall temperatures, packing pressure, and the clearance of a gas vent. On the other hand, we measure the amount of flash generated in the molding of poly(phenylene sulfide) (PPS) composites containing glass fiber and spherical fillers (CaCO₃ or Al₂O₃). Flash reduces with decreasing size of spherical fillers. These experimental data are successfully interpreted using the flash model. Polym. Eng. Sci., 45:198–206, 2005. © 2005 Society of Plastics Engineers     

Thermal response in thermal energy storage material around heat transfer tubes: effect of additives on heat transfer rates

The effects of carbon-fiber chips and carbon brushes as additives on the thermal conductivity enhancement of phase change materials (PCMs) using in latent heat thermal energy storage are investigated experimentally and numerically by considering the wall effect of the additives. The carbon-fiber chips are effective for improving the heat transfer rate in PCMs. However, the thermal resistance near the heat transfer surface is higher than that for the carbon brushes. As a result, the overall heat transfer rate for the fiber chips is lower than that for the carbon brushes. Consequently, the carbon brushes are superior to the fiber chips for the thermal conductivity enhancement under the present experimental conditions. The carbon brushes are moreover applied to the packed beds of particles to overcome their low thermal conductivity in chemical heat pump/storage. The carbon brushes essentially improve the heat transfer characteristics in the packed beds, though the thermal resistance is observed because the particles obstruct contact between the fibers and the heat transfer surfaces.     

A unified analysis of resonant converters

The general method of analysis for resonant power converters is presented. This analytical method generalizes the idea of state-space-averaging technique to overcome the limitations of the conventional state-space-averaging method. As the result, the characteristics of resonant power converters are clarified so that transfer functions and stability conditions are revealed. In addition, a computer program of analysis based on the proposed method is developed. The program can be applied to various resonant power converters, even when they have parasitic losses and higher-order resonant circuits     

Effect of cation structure on the electrochemical and thermal properties of ion conductive polymers obtained from polymerizable ionic liquids

Several onium cations having vinyl group formed ionic liquids after coupling with bis(trifluoromethanesulfonyl)imide. These monomers were polymerized, and the relation between onium cation structure and properties of thus polymerized ionic liquids was investigated. The polymerized ionic liquid having ethylimiadzolium cation unit showed the highest ionic conductivity of around 10⁻⁴ S cm⁻¹ at 30 °C among the obtained polymers reflecting the lowest glass transition temperature of −59 °C. These polymers were thermally stable and their decomposition temperatures were about 350 °C. The ionic conductivity of the polymerized ionic liquids decreased by both the addition of lithium bis(trifluoromethanesulfonyl)imide and the polymerization in the presence of cross-linker. However, the polymerized ionic liquid having 1-methylpiperidinium cation structure showed good lithium ion transference number of 0.43 at room temperature.     

Polymerization of 2-dibutylamino-1,3,5-triazine-4,6-dithiol on wire during friction process

2-Dibutylamino-1,3,5-triazine-4,6-dithiol (DB) and a mixture of DB and triallylisocyanurate (TAIC) were used as a lubricant during steel wire drawing due to a dry process. DB gave a polymer film with 180 nm in thickness to wire surfaces during the wire drawing. The polymer film had a disulfide structure on the backbone and contained a small amount of DB monomer and olygomer. Molecular weight and polymer weight increased with the drawing rate. The mixture of DB and TAIC gave mainly a three-dimensional polymer film with 225 nm in thickness to wire surfaces during drawing. The polymer film insoluble in THF had mono and disulfide structures and contained a small amount of linear polymer, DB, and TAIC. Such tribological polymerizations are estimated as follows: DB produces dithiyl radicals on a nascent surface formed during drawing and in the presence of oxygen and heat. The dithiyl radicals were polymerized by coupling with each other to give disulfide bonds or added to allyl groups in TAIC to give monosulfide bonds. It is concluded that this technique should be possible to use for unifying metal processing and surface treatment. © 1995 John Wiley & Sons, Inc.     

Separation of Polyvinyl Chloride from Plastic Mixture by Froth Flotation after Surface Modification with Ozone

Selective modification by ozonation for the surface of polyvinyl chloride (PVC) was evaluated to separate PVC from the other plastics, polyethylene terephthalate (PET), polycarbonate (PC) and polymethyl methacrylate (PMMA), with almost the same density as PVC by the froth flotation process. Ozonation could selectively decrease the contact angles of flexible PVC from 87.5 degrees to 68.4 degrees and rigid PVC from 90.3 degrees to 66.9 degrees, whereas little decreases in the contact angle were observed for other plastics. This would be due to the replacement of the chloride group on the surface of PVC, into hydrophilic functional groups; carbonyl, carboxyl and ester group. The PVC was successfully separated from the other plastics by the froth flotation process after the selective surface modification by ozonation.     

Synthesis of Ba2NaNb5O15 Powders and Thin Films Using Metal Alkoxides

Transparent and highly oriented Ba₂NaNb₅O₁₅ (BNN) thin films have been prepared by using metal alkoxides. A homogeneous precursor solution was prepared by the controlled reaction of NaOC₂H₅, Nb(OC₂H₅)₅, and barium metal. The BNN precursor included a molecular-level mixture of NaNb(OC₂H₅)₆ and Ba[Nb(OC₂H₅)₆]₂ in ethanol. The alkoxy-derived powder crystallized to a low-temperature phase, and then transformed to orthorhombic BNN (tungsten bronze) at 600°C. BNN precursor films on substrates crystallized to orthorhombic BNN at 800°C via the low-temperature phase. Highly (002) oriented BNN films of tungsten bronze structure were successfully prepared on MgO (100) substrates at 700°C by using BNN underlayer.