急性炎性疾病患者乳酸林格氏液液体动力学

目的:探索炎性疾病患者的乳酸林格氏液（Ringer's lactate,RL）液体动力学特征以及炎性生物标记物是否可以作为协变量影响RL分布和排泄。方法:本研究为前瞻性队列研究。选择40例美国麻醉医师分级（ASA）I-II级，腹腔镜下择期胆囊切除术（胆囊炎组，n=20）或者腹腔镜下急诊阑尾切除术（阑尾炎组，n=20）。所有患者麻醉诱导前开始输注RL，按15 mL/kg，35 min内输毕。采用酶联免疫（enzyme-linked immunosorbent assay,ELISA）方法测定血浆炎症（TNF-α,IL-10和CRP）或者内皮损伤生物标记物（syndecan-1,SDC-1）；利用血红蛋白（Hb）稀释-时间曲线和尿量，使用Phoenix软件，采用非线性混合效应模型分析计算RL液体动力学参数和协变量的影响。结果:与胆囊炎组相比，阑尾炎组RL从组织间隙到血浆的转运速率常数（k21）显著降低（14×10-3min-1 versus 35×10-3min-1;P=0.012）。阑尾炎组C反应蛋白（CRP）升高［中位数38.1(1.8-143.6) μg/mL versus 1.3(0.1-159.0) μg/mL;P<0.001］；与清醒状态相比，麻醉期间（输液开始后30～45 min），液体从中央室中到外周室的转运速率常数（k12）显著增加（57×10-3min-1 versus 32×10-3min-1；P<0.01）。清除速率常数（k10）降低90%（0.6×10-3min-1 versus 5.3×10-3min-1;P<0.001）。无论在清醒状态还是麻醉状态下低血压均能降低液体清除；炎症或者内膜损伤的生物标记物不能作为显著影响RL液体动力学参数的协变量。结论:阑尾炎或者胆囊炎患者术前输入液体后“炎症反应的生物标记物”不是RL的液体动力学的协变量，但是两组患者中，全身麻醉期间输入液体的清除率下降。     

Robust3D: a robust 3D face reconstruction application

In the process of reconstructing a historical event such as a rock concert only from video, the reconstruction of faces and expressions of the musicians is obviously important. However, in the process of rebuilding appearance, because of the low quality of the video of the recorded concert, the result of the reconstruction may be far from the real appearance. In this paper, a robust 3D face reconstruction application is described that can be applied to a video recording. The application first uses DeblurGAN program to run anti-ambiguity calculation and removes the ambiguity in the concert video. Then, the super-resolution program is used to enlarge every frame of the concert video by four times, thus making every frame of the video clearer. Finally, the 3D faces are obtained after 3D reconstruction of the processed video frames via the 3DMM_CNN program.

     

The analysis and comparison of two novel kinds of focusing elements as reflectors

In this article, two novel kinds of focusing elements as reflectors are analyzed and compared. One is the grooved Fresnel zone plate reflector with continuous phase‐correcting. The other called subzone paraboloid reflector, has the profile that consists of a series of paraboloids. Their diffraction efficiencies and bandwidths are described. The two elements still preserve the advantages of Fresnel zone plates, namely, low profile, high efficiency, and simple fabrication. Two dual‐reflector antennas using the proposed focusing elements as the main reflectors are simulated and the results show that these antennas have good radiation performances. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:101–108, 2015.     

Theoretical investigation of solvent effects on the selective hydrogenation of furfural over Pt(111)

It was well known that solvent effect plays a very important role in the catalytic reaction. There are many theoretical studies on the solvent effect in homogeneous catalysis while there are few theoretical studies on the solvent effect in the heterogeneous catalytic reaction and there has been no work to investigate the solvent effect on furfural transformation in heterogeneous catalysis. In the present work, both the density functional calculations and the microkinetic analysis were performed to study the selective hydrogenation of furfural over Pt(111) in the presence of methanol as well as toluene and compared with that in the gas condition. The present results indicated that the methanol can enhance the adsorption strength of furfural and other oxygen-containing reaction species due to its relatively strong polarity properties and this can be a main reason for solvent-induced high activity and selectivity. Another reason is that reaction paths study showed that the presence of methanol solvent makes the dehydrogenation of furfural less thermochemical due to the fact that furfural is more stabilized than that of dehydrogenation species, and methanol also has an inhibition effect on the dehydrogenation of furfural in the kinetic aspect, and further energetic span theory proves highest activity and selectivity for hydrogenation in methanol solvent of vapor, methanol and toluene. Moreover, microkinetic model simulation demonstrated that the activity and selectivity of hydrogenation in methanol is both higher than that in vapor and toluene. The much higher activity in methanol is due to the stabilized adsorbed reactants in the surface, which leads to a higher surface coverage of furfural. It might be proposed based on the present work that a solvent with relatively strong polarity may be favorable for the high selective hydrogenation of furfural.     

Performance investigation on a novel 3D wave flow channel design for PEMFC

Flow field structure can largely determine the output performance of Polymer electrolyte membrane fuel cell. Excellent channel configuration accelerates electrochemical reactions in the catalytic layer, effectively avoiding flooding on the cathode side. In present study, a three-dimensional, multi-phase model of PEMFC with a 3D wave flow channel is established. CFD method is applied to optimize the geometry constructions of three-dimensional wave flow channels. The results reveal that 3D wave flow channel is overall better than straight channel in promoting reactant gases transport, removing liquid water accumulated in microporous layer and avoiding thermal stress concentration in the membrane. Moreover, results show the optimal flow channel minimum depth and wave length of the 3D wave flow channel are 0.45 mm and 2 mm, respectively. Due to the periodic geometric characteristics of the wave channel, the convective mass transfer is introduced, improving gas flow rate in through-plane direction. Furthermore, when the cell output voltage is 0.4 V, the current density in the novel channel is 23.8% higher than that of conventional channel.     

Damage evolution in polymer due to exposure to high-pressure hydrogen gas

The use of hydrogen as a fuel is increasing exponentially, and the most economical way to store and transport hydrogen for fuel use is as a high-pressure gas. Polymers are widely used for hydrogen distribution and storage systems because they are chemically inert towards hydrogen. However, when exposed to high-pressure hydrogen, some hydrogen diffuses through polymers and occupies the preexisting cavities inside the material. Upon depressurization, the hydrogen trapped inside polymer cavities can cause blistering or cracking by expanding these cavities. A continuum mechanics–based deformation model was deployed to predict the stress distribution and damage propagation while the polymer undergoes depressurization after high-pressure hydrogen exposure. The effects of cavity size, cavity location, and pressure inside the cavity on damage initiation and evolution inside the polymer were studied. The stress and damage evolution in the presence of multiple cavities was also studied, because interaction among cavities alters the damage and stress field. It was found that all these factors significantly change the stress state in the polymer, resulting in different paths for damage propagation. The effect of adding carbon black filler particles and plasticizer on the damage was also studied. It was found that damage tolerance of the polymer increases drastically with the addition of carbon black fillers, but decreases with the addition of the plasticizer.     

A highly active composite electrocatalyst Ni–Fe–P–Nb2O5/NF for overall water splitting

This work demonstrates a facile Nb₂O₅-decorated electrocatalyst to prepare cost-effective Ni–Fe–P–Nb₂O₅/NF and compared HER & OER performance in alkaline media. The prepared electrocatalyst presented an outstanding electrocatalytic performance towards hydrogen evolution reaction, which required a quite low overpotential of 39.05 mV at the current density of ?10 mA cm^?2 in 1 M KOH electrolyte. Moreover, the Ni–Fe–P–Nb₂O₅/NF catalyst also has excellent oxygen evolution efficiency, which needs only 322 mV to reach the current density of 50 mA cm^?2. Furthermore, its electrocatalytic performance towards overall water splitting worked as both cathode and anode achieved a quite low potential of 1.56 V (10 mA cm^?2).     

可重构机器人模块间装配误差识别方法研究

基于对可重构机器人配对接口间位姿误差的分析划分,研制模块间装配误差在线测量识别接口,建立配对接口位姿误差与接口几何结构偏差之间的关系模型,进而建立配对接口位姿误差与配对接口内部测距传感器测量值之间的映射关系模型,提出一种基于内部测距传感器位移量的模块间装配误差在线识别、补偿方法.为验证方法的正确性,研制单关节?连杆试验平台.试验结果表明装配误差经在线识别、补偿后,连杆末端的位置误差平均值减少7倍多.     

Recent Development of Photothermal Agents (PTAs) Based on Small Organic Molecular Dyes

Photothermal therapy (PTT) has attracted great attention due to its noninvasive and effective use against cancer. Various photothermal agents (PTAs) including organic and inorganic PTAs have been developed in the last decades. Organic PTAs based on small-molecule dyes exhibit great potential for future clinical applications considering their good biocompatibility and easy chemical modification or functionalization. In this review, we discuss the recent progress of organic PTAs based on small-molecule dyes for enhanced PTT. We summarize the strategies to improve the light penetration of PTAs, methods to enhance their photothermal conversion efficiency, how to optimize PTAs’ delivery into deep tumors, and how to resist photobleaching under repeated laser irradiation. We hope that this review can rouse the interest of researchers in the field of PTAs based on small-molecule dyes and help them to fabricate next-generation PTAs for noninvasive cancer therapy.