中国卫通:创新卫星通信产业,致力数字集群服务

中国卫星通信集团公司(以下简称中国卫通)是根据国务院电信体制改革的总体部署,于2001年12月19日正式挂牌成立的国有大型骨干企业,是我国六大基础电信运营企业之一。中国卫通下设30个省级分公司和17个全资、控股、参股企业。作为我国卫星通信广播电视运营的主导企业,中国卫通以保障国家卫星通信广播安全、服务国民经济和社会发展为已任,不断以特色化通信保障国家信息网络安全,服务信息社会。特别是在卫星广播电视传输、应急指挥调度通信等特殊领域和边远农村、海上通信、自然灾害、突发事件等特殊区域,发挥了不可替代的作用,在为缩小数字鸿沟助力,构建和谐信息社会的进程中做出了重要贡献。     

交叉试验

发生了质量事故,是设备、操作等硬件的缘故,抑或药液的缘故?通过交叉试验的故事,把真相找了出来。     

Nanoscale Crystallization in Amorphous Fe–P–Mn Alloys

Mössbauer effect measurements and physicochemical analysis demonstrate that annealing of amorphous Fe–P–Mn alloys leads to the formation of a nanocrystalline structure.     

A biochar from casein and its properties

A biochar was prepared by pyrolysis of casein. A helium and mercury porosimeter were used to measure the true and apparent densities of the chars respectively, elemental and IR analysis were used to characterize the chemical composition of char. A SEM was used to observe the char surfaces in order to verify the presence of porosity. The biochar has 9.02% of nitrogen, content of porosity is 20%. The experimental results show that it is possible to prepare chars with relatively high porosity from casein for the further preparation of activated carbon.     

Effect of oxygenation on electrocatalysis of La0.6Ca0.4CoO3−x in bifunctional air electrode

A vacuum-annealed La_0.6Ca_0.4CoO_3−x was consecutively oxygenated in air at temperatures decreasing from 800 to 100 °C, and its electrocatalytic activities for oxygen reduction and evolution were then measured as a function of the oxygenation temperature. The valence of Co cation, changing between +2 and +3, was found susceptible to annealing either in vacuum or air. The catalytic activities initially decrease monotonically as the oxygenation temperature was decreased from 800 to 300 °C, as a result of increasing oxygen content, and then rise abruptly with the oxygen reduction activity reaching a maximum at 200 °C and the oxidation activity at 150 °C. X-ray photoelectron spectroscopy analysis indicated that the enhancements by the low-temperature oxygenation involved increased OH coverage and less charged cations at surface. The results clearly reveal the importance of the post-calcination annealing process for optimizing the performance of La_0.6Ca_0.4CoO_3−x in air electrode applications.     

一种微透镜阵列的研制

介绍一种利用表面张力的作用、以光纤作材料、用分离的自聚焦透镜制作微透镜阵型的方法，这种方法具有制作工艺简单、无须昂贵设备等优点，用此方法实际制作了具有良好连续面型的微透镜阵列，并对制作的微透镜阵列进行了测试，效果较好。     

Improvement of AlGaInP light emitting diode by sulfide passivation

The brightness of AlGaInP light emitting diodes (LEDs) has been raised by a factor of 1.12 at 20 mA by sulfide passivation. Meanwhile, the sulfide also can decrease leakage current of AlGaInP LEDs at -2 V to nearly one thousandth of that in the as-fabricated device. The possible causes for the brightness increase of AlGaInP LEDs after sulfide treatment including surface roughness, reduction of Fresnel loss, and effective injection of carriers were demonstrated.     

洼60-H26水平井套铣打捞技术

洼60-H26井是一口中曲率水平井,设计井深1 922 m,由于地面条件的限制,设计采用三维井眼轨道。该井水平段在钻至井深1 801 m时,发生卡钻事故。在卡钻事故处理过程中,采用测卡、爆炸松扣技术取出上部钻具后,应用了不同规格的套铣管对被卡钻具进行套铣,采用间歇式套铣方式实现了大斜度井段(45°-90°)的安全套铣,采用短套铣管完成了时水平井段内φ215．0 mm稳定器的套铣,采用φ228．6 mm套铣管成功套铣水平井段被卡LWD仪器,最后通过震击器震击成功解卡。详细介绍了洼60-H26水平井卡钻事故的处理过程,分析了在水平段处理卡钻事故的难点。该井处理卡钻事故的经验,对以后水平井施工中处理井下事故、打捞贵重仪器具有借鉴价值。     

布帮鞋无浆贴合工艺技术

本工艺是对原有工艺的改进，突破了原有布帮鞋不能采用无浆贴合的局限性，对原有工艺中的不足有了很大的改进，提高了生产效率，改善了鞋子外观质量，增加了鞋子的美观性。     

Suppression control method for torque vibration of three-phase HB-type stepping motor utilizing feedforward control

This paper proposes a method to reduce the vibration of the three-phase HB-type stepping motor with cogging torque by the feedforward compensation control. The compensation signal to suppress the vibration of the motor frame is obtained by the repetitive controller installing an online Fourier transformer and utilizing an acceleration sensor attached to the motor frame or an acoustic sensor such as a microphone placed close to the frame. The sensor is used only for the acquisition of the feedforward compensation data. The feedforward compensation signal at an arbitrary operating point is derived from the amplitude and phase data of the frequency components and the operating point data. Compensation data obtained by the repetitive controller is applied to the operating point changed by reference frequency and load condition in steady state. The compensation signal for the new operating point will be generated from compensation data utilizing polynomial equation approximation and linear interpolation method. The effectiveness of this proposed method is confirmed by the experimental results.