Evaluation of direct light processing for the fabrication of bioactive ceramic scaffolds: Effect of pore/strut size on manufacturability and mechanical performance

Bioactive ceramic scaffolds for bone regeneration consisting of a three-dimensional mesh of interpenetrating struts with square section were fabricated via Digital Light Processing (DLP). The ability of the technique to manufacture 3D porous structures from β-tricalcium phosphate (β-TCP) powders with different dimensions of struts and pores was evaluated, identifying the possibilities and limitations of the manufacturing process. Small pore sizes were found to seriously complicate the elimination of excess slurry from the scaffold’s innermost pores. The effect of the strut/pore size on the mechanical performance of the scaffolds under compressive stresses was also evaluated, but no significant influence was found. Under compressive stresses, the structures resulted weaker when tested perpendicularly to the printing plane due to interlayer shear failure. Interlayer superficial grooves are proposed as potential failure-controlling defects, which could also explain the lack of a Weibull size effect on the mechanical strength of the fabricated DLP scaffolds.     

Polarity Effect and Electromagnetic Radiation of Partial Discharge Accompanying Growth of Electrical Tree

We have investigated the characteristics of radiated electromagnetic (EM) waves from positive and negative partial discharges (PD) in epoxy resin and cross‐linked polyethylene. We found that there is a correlation among the EM level from PD, the positive PD current, and electrical trees. Therefore, the growth of an electrical tree produces a lot of positive PD. We have also investigated the characteristics of the frequency region of EM waves from PD in air, insulating oil, and liquid epoxy in addition to the above insulators. EM waves were detected in the frequency region of 40 MHz to 300 MHz from positive and negative PD in epoxy resin and cross‐linked polyethylene. EM waves were also detected in the frequency region of 40 MHz to 150 MHz from positive and negative PD in air. In the case of insulating oil and liquid epoxy, EM waves were detected in the frequency regions of 40 MHz to 150 MHz from positive PD, and 40 MHz to 250 MHz from negative PD. The frequency region differed depending on the material and the discharge polarity. Our investigation indicates that the cause is differences in electric field strength at the time of PD occurrence.     

The Emi2 Protein of Saccharomyces cerevisiae is a Hexokinase Expressed under Glucose Limitation

Hexokinases catalyze glucose phosphorylation at the first step in glycolysis in eukaryotes. In the budding yeast Saccharomyces cerevisiae , three enzymes for glucose phosphorylation have long been known: Hxk1, Hxk2, and Glk1. In this study, we focus on Emi2, a previously uncharacterized hexokinase-like protein of S. cerevisiae . Our data show that the recombinant Emi2 protein (rEmi2), expressed in Escherichia coli , possesses glucose-phosphorylating activity in the presence of ATP and Mg ²⁺ . It was also found that rEmi2 phosphorylates not only glucose but also fructose, mannose and glucosamine in vitro . In addition, we examined changes in the level of endogenous Emi2 protein in S. cerevisiae in the presence or absence of glucose and a non-fermentable carbon source. We found that the expression of Emi2 protein is tightly suppressed during proliferation in high glucose, while it is strongly upregulated in response to glucose limitation and the presence of a non-fermentable carbon source. Our data suggest that the expression of the endogenous Emi2 protein in S. cerevisiae is regulated under the control of Hxk2 in response to glucose availability in the environment.     

Fracture toughness evaluation of adjacent flow weld line in polystyrene by the SENB method

Fracture toughness of adjacent flow weld lines, defined as weld lines that occur when two flow fronts meet and continue to flow together in the same direction (meld line or hot weld line), was evaluated by the single‐edge notched‐bend (SENB) method using three differently‐shaped obstructive pins. Although the fracture toughness varied depending upon the shapes of the pin, the values could be standardized as the distance from the meeting point of the two flow fronts flowing around the pin. The fracture toughness decreased drastically from the meeting point along the weld line and then slightly increased. These characteristic features could be explained by flow‐induced molecular orientation at the weld line interface. The molecules around the meeting point that were initially oriented parallel to the weld line due to fountain flow were able to relax, and then entanglement across the weld line interface developed because the flow stopped in the middle of the filling process, resulting in high fracture toughness. In contrast, the material at the downstream side of the weld line continued flowing during the filling process, being stretched along the flow direction. So, the molecular orientation at this area could not relax. In addition, the V‐notch shape, i.e., the depth and length at the surface of the weld line, which also varied depending on the shape of the obstacles, was considered to be identical when the meeting point was allowed to be a datum point. Thus, the meeting point was found to be a significant factor when the properties of weld lines are investigated. POLYM. ENG. SCI., 45:1059–1066, 2005. © 2005 Society of Plastics Engineers     

A flow simulation for the epoxy casting process using a 3D finite‐element method

A three‐dimensional flow simulation for epoxy casting has been developed. A control‐volume‐based finite‐element method is employed, containing a conservative upwind formulation for the advection terms and equal order interpolations for all variables. This simulation predicts the non‐isothermal and reactive flow behavior under the gravity. The viscosity and reaction‐rate parameters were estimated by using a dynamic rheometer and a differential scanning calorimeter. The predicted flow front advancement and temperature profiles in the calculation domain similar to the mold cavity were in close agreement with the corresponding experimental results. The variation of epoxy surface configuration with flow rate also showed the same tendency between the prediction and the experiment. This simulation seems to be applicable not only to the epoxy casting, but also to other molding processes of various thermoset resins. POLYM. ENG. SCI. 45:364–374, 2005. © 2005 Society of Plastics Engineers.     

Construction of the plasmid PMEX8-HAK1 and random site-directed mutagenesis of human cytosolic adenylate kinase

The pMEX8-hAK1 vector was devised from the pAK plasmid (Kim J. H. et al., 1989, Protein Engineering 5, 379-386), which could directly express human adenylate kinase proteins without recombination and its single strand DNA could be withdrawn with helper phage for random site-directed mutagenesis. The conserved key residues at Lys21, Lys27, and Thr39 were engineered to obtain mutants for kinetic analysis. Three mutants were obtained as K21P, K27R, and T39S, their specific activities were strikingly reduced compared to those of wild type adenylate kinase. This pMEX8-hAK1 will be a powerful tool for site-directed mutagenesis to detect the substrate-enzyme interaction for human adenylate kinase including various other enzymes.     

Thermal response in thermal energy storage material around heat transfer tubes: effect of additives on heat transfer rates

The effects of carbon-fiber chips and carbon brushes as additives on the thermal conductivity enhancement of phase change materials (PCMs) using in latent heat thermal energy storage are investigated experimentally and numerically by considering the wall effect of the additives. The carbon-fiber chips are effective for improving the heat transfer rate in PCMs. However, the thermal resistance near the heat transfer surface is higher than that for the carbon brushes. As a result, the overall heat transfer rate for the fiber chips is lower than that for the carbon brushes. Consequently, the carbon brushes are superior to the fiber chips for the thermal conductivity enhancement under the present experimental conditions. The carbon brushes are moreover applied to the packed beds of particles to overcome their low thermal conductivity in chemical heat pump/storage. The carbon brushes essentially improve the heat transfer characteristics in the packed beds, though the thermal resistance is observed because the particles obstruct contact between the fibers and the heat transfer surfaces.     

Effect of antioxidant contained in poly(ethylene glycol) on cell fusion

The effect of antioxidants contained in poly(ethylene glycol) (PEG) on cell fusion was studied using L929 cells in the monolayer state. Hydroquinone monomethyl ether (HQME), 2-mercaptobenzimidazole (MB), butyl hydroxyanisole (BHA) and 2,6-di-(t-butyl)-4-methylphenol (BHT) were chosen from the antioxidants that have currently been used to protect commercially available PEG from oxidation. Cell culture was conducted in 40% w/w aqueous solution of PEG with a molecular weight of 3000 in the presence of different concentrations of antioxidants. BHA clearly enhanced membrane fusion of L929 cells with increasing concentration in PEG solution, whereas HQME, MB and BHT had no significant effect on cell fusion. The enhancement of cell fusion by BHA might be ascribed to balanced hydrophobicity and high water solubility in comparison with the other three antioxidants.