Polarity Effect and Electromagnetic Radiation of Partial Discharge Accompanying Growth of Electrical Tree

We have investigated the characteristics of radiated electromagnetic (EM) waves from positive and negative partial discharges (PD) in epoxy resin and cross‐linked polyethylene. We found that there is a correlation among the EM level from PD, the positive PD current, and electrical trees. Therefore, the growth of an electrical tree produces a lot of positive PD. We have also investigated the characteristics of the frequency region of EM waves from PD in air, insulating oil, and liquid epoxy in addition to the above insulators. EM waves were detected in the frequency region of 40 MHz to 300 MHz from positive and negative PD in epoxy resin and cross‐linked polyethylene. EM waves were also detected in the frequency region of 40 MHz to 150 MHz from positive and negative PD in air. In the case of insulating oil and liquid epoxy, EM waves were detected in the frequency regions of 40 MHz to 150 MHz from positive PD, and 40 MHz to 250 MHz from negative PD. The frequency region differed depending on the material and the discharge polarity. Our investigation indicates that the cause is differences in electric field strength at the time of PD occurrence.     

InxGa1−xAs ohmic contacts to n-type GaAs with a tungsten nitride barrier

Significant reduction of the contact resistance of In_0.7Ga_0.3As/Ni/W contacts (which were previously developed by sputtering in our laboratory) was achieved by depositing a W₂N barrier layer between the Ni layer and W layer. The In_0.7Ga_0.3 As/Ni/W₂N/W contact prepared by the radio-frequency sputtering technique showed the lowest contact resistance of 0.2 Ωmm after annealing at 550°C for 10 s. This contact also provided a smooth surface, good reproducibility, and excellent thermal stability at 400°C. The polycrystalline W₂N layer was found to suppress the In diffusion to the contact surface, leading to improvement of the surface morphology and an increase in the total area of the In_xGa−As between metal and the GaAs substrate. These improvements are believed to reduce the contact resistance.     

Effect of antioxidant contained in poly(ethylene glycol) on cell fusion

The effect of antioxidants contained in poly(ethylene glycol) (PEG) on cell fusion was studied using L929 cells in the monolayer state. Hydroquinone monomethyl ether (HQME), 2-mercaptobenzimidazole (MB), butyl hydroxyanisole (BHA) and 2,6-di-(t-butyl)-4-methylphenol (BHT) were chosen from the antioxidants that have currently been used to protect commercially available PEG from oxidation. Cell culture was conducted in 40% w/w aqueous solution of PEG with a molecular weight of 3000 in the presence of different concentrations of antioxidants. BHA clearly enhanced membrane fusion of L929 cells with increasing concentration in PEG solution, whereas HQME, MB and BHT had no significant effect on cell fusion. The enhancement of cell fusion by BHA might be ascribed to balanced hydrophobicity and high water solubility in comparison with the other three antioxidants.     

Tissue compatibility of polylactic acids in the skeletal site

This study was undertaken to examine the osseous tissue compatibility of polylactic acid (PLA) with properties of bioabsorbability and plasticity. Two kinds of granular PLA with different molecular weight (PLA-H: 28 000 MW, PLA-L: 10 600 MW) were implanted into rat tibiae and light microscopic sections were prepared at 1, 2, 4, 8, 16, and 24 weeks following surgery. The tissue compatibility of the PLAs was compared with that of hydroxyapatite (HAP) which is a non-absorbable biocompatible material. After implantation, both PLAs were gradually absorbed and replaced by marrow tissue at 24 weeks. PLA-H degraded slower than PLA-L. New bone formation was observed around each PLA by 4 weeks, and a vast amount of bone deposited on PLA-H at 16 weeks. Phagocytic reactions to the PLAs were noted, however, severe inflammation was not seen. HAP was not absorbed and bone surrounded it throughout the experiment. These results indicate good tissue compatibility of PLA as a bioabsorbable material at the skeletal site.     

A video DSP with a macroblock-level-pipeline and a SIMD typevector-pipeline architecture for MPEG2 CODEC

A video DSP with macroblock-level-pipeline and a SIMD type vector-pipeline architecture (VDSP2) has been developed, using 0.5 μm triple-layer-metal CMOS technology. This 17.00 mm×15.00 mm chip consists of 2.5 M transistors, and operates at 100 MHz. The real-time encoder and decoder specified in the MPEG2 main profile at the main level can be realized with two VDSP2's and a motion estimation (ME) unit, and one VDSP2 respectively, at an 80 MHz clock rate, with a total power dissipation of 4.2 W at 3.3 V     

Thermodynamic study of the phase equilibria in the Sn−Ti−Zn ternary system

The Sn−Ti−Zn ternary phase diagram has been constructed using the CALPHAD technique. The Ti−Zn binary system phase boundaries were determined using differential scanning calorimetry and the solid-liquid diffusion couples method. In addition, the formation energy of some stoichiometric compounds was obtained using first-principle band energy calculations. For the ternary system, some alloys were prepared by equilibration at 600 or 700 °C, and the compositions of the precipitates were analyzed using electron probe microanalysis. Thermodynamic assessment of the Ti−Zn and Sn−Ti−Zn systems was performed based on the experimental information and by adopting reported values of the thermodynamic properties of the Sn−Zn and Sn−Ti binary systems. Microstructural observation showed that Sn₃Ti₅Zn₁₂ exists in the ternary system. Seven types of invariant reaction on the Sn-rich liquidus surface of the ternary system are predicted by the phase diagram calculations. The ternary eutectic point falls at 0,0009 mass% Ti and 8.69 mass% Zn, at T=192.40°C, which is slightly lower than the calculated eutectic point of Sn−Zn binary alloy (T=192.41°C). Based on these results, a nonequilibrium solidification process using the Scheil model was simulated. This paper was presented at the International Symposium on User Aspects of Phase Diagrams, Materials Solutions Conference and Exposition, Columbus, Ohio, 18–20 October, 2004.     

Fat splitting by the twitchell process at low temperature

Summary A study was made of the degree of splitting of coconut and soybean oils by the Twitchell process at 35±0.1°C. with no shaking or stirring, using an agent consisting mainly of tetrabutyl naphthalene sulfonic acid with water or dilute sulfuric acid. The degree of splitting was greater with sulfuric acid than with water. In general, the degree of splitting of soybean oil was greater when the sulfonic acid was dissolved in the oil layer than when it was in water. The reverse was true with coconut oil. Although addition of glycerol had no effect on the degree of splitting, addition of glacial acetic acid to the coconut oil system decreased fat splitting to a considerable extent. Addition of coconut fatty acids to the coconut oil system had little effect, but soybean fatty acids added to the soybean oil system markedly increased the degree of splitting. For the first time it has been demonstrated that, at 35±0.1°C., splitting of a fat by the Twitchell process occurs in a stepwise way. Coconut oil in contact with 1N sulfuric acid containing the sulfonic acid, corresponding to 1% by the weight of the oil, was about 90% split in 15 to 30 days, depending on the area of contact of the two layers. The diglyceride concentration reached a maximum during the early days of the reaction and then decreased somewhat. Monoglyceride concentration appeared to reach a maximum more slowly and then continued at that level as the concentrations of free fatty acids and glycerol steadily increased. Presented at the symposia on fat of the Chemical Society of Japan, Nov. 10, 1954, and Nov. 8, 1955, Nagoya, Japan; and the 8th annual meeting of the Chemical Society of Japan, Apr. 2, 1955, Tokyo, Japan.     

Lysozyme requires fluctuation of the active site for the manifestation of activity

Mutations around His15 which lie far away from the active site,stimulated glycol chitin activity of lysozyme at physiologicaltemperature. Del-Argl4Hisl5 lysozyme, a mutant lysozyme whoseArgl4 and Hisl5 were deleted together, and has the highest activityamong these mutant lysozymes, had a similar binding abilityto a trimer of N-acetyl-glucosamine, a substrate analogue, relativeto native lysozyme. This suggests that the increased activitywas due to an increased k_cat in the catalysis reaction. TheH-D exchange rate of the N-1 proton in the Trp63 which is locatedin the active site cleft, was enhanced in the Del-Argl4Hisl5lysozyme, while 2-D proton NMR analysis revealed no conformationalchange around Trp63. We conclude that some sort of fluctuationat the active site might be required for the manifestation ofactivity. This theory is supported by the finding that the Del-Argl4Hisl5lysozyme showed a shift in temperature dependency of activityto lower temperatures compared with that of native lysozyme.     

Local disturbances preceding a running crack front in a viscoelastic solid

The local disturbances ahead of a running crack front in a viscoelastic solid were measured through noncontact electro-optical tools. It was observed that the very high local strain rate up to 200/sec exists even in the present quasistatic loading case. It may be concluded that the running crack propagation velocities, not the conventional average strain rates ranging from about 10^?4/sec to 10^?2/sec, govern the local disturbances, as the crack propagation velocities always exceed 200m/sec for both average strain rates, while the local strain rates observed do not show much differences between both average strain rate cases.     

Novel synthesis of microcrystalline titanium(IV) oxide having high thermal stability and ultra-high photocatalytic activity: thermal decomposition of titanium(IV) alkoxide in organic solvents

Thermal decomposition of titanium(IV) tetra-tert-butoxide (TTB) in inert organic solvents at 573 K yielded microcrystalline anatase (titanium(IV) oxide, TiO₂) powders with a crystallite size of ca. 9 nm and a surface area of <100 m² g^-1. Primary and secondary alkoxides of titanium(IV), however, were not decomposed under similar conditions, indicating that the thermal stability of C-O bonds in the alkoxides was a decisive factor for their decomposition. The TiO₂ prepared from TTB by this manner was thermally stable upon calcination in air and retained high surface area of ca. 100 m² g^-1 even after calcination at 823 K. The as-prepared TiO₂ powders, without calcination, exhibited much higher rate of carbon dioxide formation than any other active photocatalysts such as Degussa P-25 and Ishihara ST-01 in the photocatalytic mineralization of acetic acid in aerated aqueous solutions. The higher activity of the present TiO₂ photocatalysts is attributed to both high crystallinity and large surface of the present product. The calcination of the as-prepared TiO₂ in air reduced the photocatalytic activity, but it was still higher than the other commercially available TiO₂'s. This revised version was published online in July 2006 with corrections to the Cover Date.