Feedback control of decoupled bending and torsional vibrations of flexible beams

In this article, we consider a flexible beam with a rigid body, of which the bending vibration and the torsional vibration are decoupled. Therefore we need two control motors to suppress the vibrations. Each set of dynamic equations is treated in the form of an appropriate Hilbert space. A stabilizing feedback control law of each rotation motor will be established on the basis of modal analysis. A set of experiments has been carried out, and the results demonstrate the effectiveness of the dynamic model and the proposed control law. © 1994 John Wiley & Sons, Inc.     

High-efficiency finishing process for metal mold by large-area electron beam irradiation

A new finishing process for metal molds by large-area electron beam (EB) irradiation is proposed in this study. In the large-area EB irradiation equipment used here, an EB with high-energy density is irradiated without focusing the beam, and so the EB with a maximum diameter of 60 mm can be used for melting or evaporating metal surface instantly. Experimental results show that the surface roughness decreases from 6 μmRz to less than 1 μmRz in just a few minutes under proper machining conditions. The corrosion resistance of metal mold surface also could be greatly improved by large-area EB irradiation. Furthermore, the surface roughness of tilting surface close to 90° could be well improved. Therefore, large-area EB irradiation method has a possibility to become a high-efficiency finishing process for metal molds.     

Paraneoplastic neurologic syndromes. 2. Lambert-Eaton myasthenic syndrome. 1) The molecular structure of calcium channel and immunology

The effect of divalent cations on the inactivation of Escherichia coli by high hydrostatic pressure was investigated. The presence of 0.5 mmol l-1 of CaCl2, MgCl2, MnCl2 and FeCl2 reduced pressure inactivation of E. coli MG1655, while 0.5 mmol l-1 of ZnCl2, NiCl2, CuCl2 and CoCl2 increased inactivation. Baroprotection by Ca2+ was found to be dose-dependent up to at least 80 mmol l-1 and was studied in more detail in terms of inactivation kinetics. Logarithmic survivor plots against time deviated from first order kinetics, suggesting that MG1655 cultures were heterogeneous with regard to pressure resistance. All cultures were shown to contain a small proportion of cells that were only slowly inactivated. Addition of Ca2+ increased the proportion of these tolerant cells in the cultures up to 1000-fold at 80 mmol l-1, but did not affect their inactivation rate. The addition of EDTA resulted in the opposite effect, lowering the proportion of pressure-tolerant cells in the cultures. Three pressure-resistant mutants of E. coli MG1655 were found to be more resistant to EDTA under pressure compared with MG1655, and were unaffected by Ca2+ under pressure. In addition, these mutants had a 30-40% lower Ca2+ content than MG1655. Based on these results, it is postulated that pressure killing of E. coli MG1655 is mediated primarily by the destabilization of Ca(2+)-binding components, and that the mutations underlying pressure resistance have resulted in pressure-stable targets with reduced Ca(2+)-binding affinity.     

A novel spin-finishing method for antistatic modification of polyester fiber. Surface reaction onto amine-containing copoly(amide-ethers) blended with polyester fiber

Copoly(amide-ethers) containing two types of tertiary amine units were made as antistatic modifiers for poly(ethylene terephthalate) (PET) fibers. The filaments of the copolymers were melt-spun and reacted with three alkylating agents in order to quaternize the tertiary amine into a sulfo-betaine, a carbobetaine, and an ammonium ion. The apparent electric resistivity of the filaments was greatly reduced by this reaction, being in the range of 10⁶ to 10⁸ Ω/cm. However, because these quaternized copolymers incurred decomposition during blend spinning with PET, a blend PET fiber containing one type of copoly(amide-ether) was melt-spun and subjected to quaternization of the amino groups as well as to surface crosslinking with various alkylating and epoxy agents. The quaternized blend fibers obtained showed improved antistatic properties compared with the original blend fiber. Particularly, the fibers crosslinked with epoxy compounds were found to have the best antistatic properties that had ever been attained with this type of modification. The antistatic properties were retained even after dyeing, because both hydrophilic and ionic groups had been effectively immobilized on the surface. Since this quaternization and crosslinking could be conducted on-line with spinning and drawing within a short reaction time, this modification technique is called “spin-finishing method”, which should be superior to the conventional methods in terms of cost performance and productivity.     

Polymerization of 2-dibutylamino-1,3,5-triazine-4,6-dithiol on wire during friction process

2-Dibutylamino-1,3,5-triazine-4,6-dithiol (DB) and a mixture of DB and triallylisocyanurate (TAIC) were used as a lubricant during steel wire drawing due to a dry process. DB gave a polymer film with 180 nm in thickness to wire surfaces during the wire drawing. The polymer film had a disulfide structure on the backbone and contained a small amount of DB monomer and olygomer. Molecular weight and polymer weight increased with the drawing rate. The mixture of DB and TAIC gave mainly a three-dimensional polymer film with 225 nm in thickness to wire surfaces during drawing. The polymer film insoluble in THF had mono and disulfide structures and contained a small amount of linear polymer, DB, and TAIC. Such tribological polymerizations are estimated as follows: DB produces dithiyl radicals on a nascent surface formed during drawing and in the presence of oxygen and heat. The dithiyl radicals were polymerized by coupling with each other to give disulfide bonds or added to allyl groups in TAIC to give monosulfide bonds. It is concluded that this technique should be possible to use for unifying metal processing and surface treatment. © 1995 John Wiley & Sons, Inc.     

Ultra-high pressure sterilization of powdery food stuff—a new application of a roller compactor

A new non-heating technique was developed for the sterilization of food stuff. Applying a roller compactor, ultra-high pressure sterilization has experimentally demonstrated its ability to sterilize dry powders, such as corn flour and Chinese herbs, with little quality deterioration. Also, the degree of food sterilization was found correlated well with the linear press forces between the rollers, roller gaps, and number of compaction passes. In comparison to the conventional high pressure sterilization technique, the new dry continuous processing method has the advantage of lower investment cost and is more versatile for sterilizing various food powders.     

Three-dimensional simulation using fixed coarse-grid thermal-fluid scheme and conduction heat transfer scheme in distinct element method

Three-dimensional simulation using particle-thermal-fluid coupling scheme with a mixed Lagrangian-Eulerian approach is presented and the scheme is described by extending author's previous research [Y. Shimizu, 2004. “Fluid Coupling in PFC2D and PFC3D”, numerical modeling in micromechanics via particle methods—2004, Proceeding of 2nd International PFC Conference, Balkema, 2004, pp. 281-287]. The scheme solves the continuity, Navier-Stokes (N-S) and thermal energy equations numerically in Eulerian Cartesian coordinates, then derives pressure, velocity vectors and temperature for each fixed cell by considering particle existence. On the other hand, driving forces and thermal energy from fluid are applied to the particles as external body forces and a source term in the force-displacement law and the heat transfer calculations, respectively. This paper describes the thermal scheme for both fluid and particles. Results of two- and three-dimensional simulations involving forced convective heat transfer by fluid and conduction heat transfer within particles are presented.     

The effect of sputter etching on the surface characteristics of dyed aramid fabrics

Three kinds of aramid fabrics, Technora (modified p-aramid), Conex (m-aramid) and Kevlar (p-aramid), were subjected to sputter etching and argon low-temperature plasma treatments after dyeing in black with disperse dyes. The depth of shade increased considerably on Technora and Kevlar with the sputter etching treatment, but not on Conex fabrics. Argon low-temperature plasma treatment had virtually no effect on the depth of shade on the aramid fabrics.     

Syntheses and conformational studies of poly(S-menthyloxycarbonylmethyl l- and d-cysteines)

S-menthyloxycarbonylmethyl l- and d-cysteines were prepared by the reaction of l- or d-cysteine and (?)-menthyl chloroacetate in liquid ammonia and were then polymerized to poly(S-menthyloxycarbonylmethyll- and d-cysteines) by the N-carboxyanhydride (NCA) method. From the results obtained by means of infra-red spectra, X-ray diffractions, optical rotatory dispersions (o.r.d.), and circular dichroisms (c.d.), $\text{poly}\text{(S-}\text{menthyloxycarbonylmethyl-}\text{l}\text{-cysteine}\text{)}$ was found to be a right-handed α-helix in the solid state and in ethyl ether/chloroform and chloroform solutions. Similarly, $\text{poly}\text{(S-}\text{menthyloxycarbonylmethyl-}\text{d}\text{-cysteine}\text{)}$ was a left-handed α-helix. The helix-coil transition of these polymers was observed in the vicinity of 3–4% trifluoroacetic acid (TFA) in chloroform/TFA mixtures.