Decreasing the number of test specimens by utilizing both fracture stress and fracture location for the estimation of Weibull parameter

In a bending load test for brittle materials, such as ceramics for spacecraft and aircraft, decreasing the number of test specimens required is a crucial problem. This paper discusses the effectiveness of using the information of both fracture stress and fracture location to decrease the number of specimens required to obtain the same precision as the Weibull estimator. The following results were obtained: It was found that by adding the fracture location information, the precision of the Weibull parameter estimation under the optimal design became 1.5–1.9 times better compared with the case of using only the fracture stresses. This means the number of samples necessary to attain the same precision becomes 1/1.5–1/1.9. Tables and figures which give information on the number of samples necessary to attain the required precision are given.     

Volumetric properties of mixtures of 1,4-dioxane and water at high pressures

Densities of aqueous of 1,4-dioxane have been measured at temperatures from 298 to 348 K and at pressures up to 40 MPa by a vibrating-tube method. Molar volumes obtained with an estimated uncertainty of ±0.2°,% are correlated with pressure by the Tait equation within the experimental uncertainty. Pressure and composition dependences of the excess molar volume, partial molar volume, and isothermal compressibility are determined and they are compared with those of other aqueous solutions.     

Thermal response in thermal energy storage material around heat transfer tubes: effect of additives on heat transfer rates

The effects of carbon-fiber chips and carbon brushes as additives on the thermal conductivity enhancement of phase change materials (PCMs) using in latent heat thermal energy storage are investigated experimentally and numerically by considering the wall effect of the additives. The carbon-fiber chips are effective for improving the heat transfer rate in PCMs. However, the thermal resistance near the heat transfer surface is higher than that for the carbon brushes. As a result, the overall heat transfer rate for the fiber chips is lower than that for the carbon brushes. Consequently, the carbon brushes are superior to the fiber chips for the thermal conductivity enhancement under the present experimental conditions. The carbon brushes are moreover applied to the packed beds of particles to overcome their low thermal conductivity in chemical heat pump/storage. The carbon brushes essentially improve the heat transfer characteristics in the packed beds, though the thermal resistance is observed because the particles obstruct contact between the fibers and the heat transfer surfaces.     

Non-linear current–voltage characteristics related to native defects in SrTiO3 and ZnO bicrystals

SrTiO₃ and ZnO bicrystals with various types of boundaries were fabricated in order to examine their current–voltage characteristics across single grain boundaries. Their grain boundary structures were also investigated by high-resolution transmission electron microscopy. In Nb-doped SrTiO₃, electron transport behaviors depend on the type of boundaries. Random type boundaries exhibit highly non-linear current–voltage characteristics, while low angle boundaries show a slight non-linearity. On the contrary, undoped ZnO does not exhibit non-linear current–voltage characteristics in any type of boundaries including random ones. It is suggested that the differences observed in current–voltage properties between the two systems are mainly due to the difference in the accumulation behavior of acceptor-like native defects at grain boundaries. A clear non-linearity is obtained by means of Co-doping even for the highly coherent Σ1 boundary in a ZnO bicrystal. This is considered to result from the production of acceptor-like native defects by Co-doping.     

Is it possible to differentiate between choledochal cyst and congenital biliary atresia (type I cyst) by antenatal ultrasonography?

Both choledochal cyst and congenital biliary atresia (type I cyst) may share the same ultrasonographic pattern. We report 2 cases which were shown to have cystic structures on the upper abdomen by antenatal ultrasonography. The size of the choledochal cyst found at 24 weeks' gestation increased steadily as gestational age advanced. But the size of the cyst in congenital biliary atresia found at 29 weeks' gestation remained unchanged throughout the remaining pregnancy. Cyst enlargement, therefore, may suggest the possibility of a choledochal cyst.     

Forming mental models in learning operating procedures for terminalequipment

People faced with an unfamiliar product or service tend to fall back on mental models based on analogical relationships with familiar products or services. Two experiments on the analogical relationships or metaphors that people might use when operating a communications terminal are described. In the first experiment, the role previously acquired operating knowledge has in determining the mental models people use when directory dialing with novel equipment is examined. In a second experiment, it is shown that an explicit appeal to an analogy between conventional mail and electronic mail can help users learn to use an electronic mail system, and make it easier for them to remember how to use the system as long as 90 days after initial exposure. It is concluded that the mental model is constructed only from the user's operating knowledge acquired as a result of past experiences, and the metaphor method is effective when the instructions are metaphorically taught     

A 64-Mb DRAM with meshed power line

A 64-Mb dynamic RAM (DRAM) has been developed with a meshed power line (MPL) and a quasi-distributed sense-amplifier driver (qDSAD) scheme. It realizes high speed, t_RAS=50 ns (typical) at V_cc=3.3 V, and 16-b input/output (I/O). This MPL+qDSAD scheme can reduce sensing delay caused by the metal layer resistance. Furthermore, to suppress crosstalk noise, a V_SS shield peripheral layout scheme has been introduced, which also widens power line widths. This 64-Mb DRAM was fabricated with 0.4-μm CMOS technology using KrF excimer laser lithography. A newly developed memory cell structure, the tunnel-shaped stacked-capacitor cell (TSSC), was adapted to this 64-Mb DRAM     

Micro-computerized tomographic observation of the spinning apparatus in Bombyx mori silkworms

Silkworms and spiders have evolved complex spinning apparatus thought to use highly controlled conditions to optimize protein folding and crystallization to provide a tough fiber. Accordingly, the structure and function of the natural spinning apparatus has been studied with great attention as an interesting piece of biological engineering with potential for mimicry in an industrial process. However it is still not well understood. Here we used Micro-Computerized Tomographic equipment (mCT) to visualize the three-dimensional structure of the spinning apparatus in Bombyx mori silkworms. Multidirectional tomograms obtained by X-ray radioscopy provided valuable information on the detailed arrangement of each muscle of the silk press. It is suggested that the duct in the silk press part plays a part as an extrusion die whose cross-sectional area can be controlled by muscles to optimize applied stresses in the partially gelled silk within its lumen.