Transmittance and cathodoluminescence of AlN ceramics sintered with Ca3Al2O6 as sintering additive

Aluminum nitride ceramics were prepared by sintering with 0–4.8 mass% of Ca₃Al₂O₆ (C₃A) as a sintering additive. The transmittance in the range of 260–550 nm increased with increasing amount of C₃A. The cathodoluminescence intensity attributed to oxygen-induced defects decreased with increasing amount of C₃A. From the results, the increase of the transmittance in the range of 260–550 nm was considered to be related to the decrease of the oxygen-induced defect density.     

Real-time measurement of pointing action by using DSP

This paper presents an approach of measuring in real-time the vector of finger that is pointing to an object. DSP is used in the operation processing unit in order to do the real-time processing. The steps include the extraction of flesh-colored regions from an image, the labeling of the flesh-colored regions, and the detection of two characteristic positions on the finger so that the direction that the finger is pointing at will be calculated. The entire process takes about 29 msec, which makes it possible to have the frame rate of 34 fps. With this frame rate, this measurement approach is considered real-time and promising to be merged into other application systems. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008     

Three-dimensional display of the bronchi using helical CT

The purpose of this study was to evaluate the clinical usefulness of three-dimensional (3D) images of the bronchi obtained using helical CT. Thirteen patients with lung cancer, one with tracheal diverticulum, and one with bronchial amyloidosis were examined. The CT scanner employed was the Toshiba Xforce. The helical CT scan cycle consisted of 20 continuous rotations, each requiring 1.5 sec, for a total scanning time of 30 sec. Scans were obtained using a 5-mm X-ray beam width, a 5-mm/1.5 sec couchtop sliding speed, and a 2-mm reconstruction interval. 3D images were reconstructed using a CEMAX VIPstation. The optimal lower and upper threshold CT values for 3D images of the bronchi were -650 and -100 HU, respectively, and 3D images clearly depicted endobronchial lesions. Cartilage crescents were also demonstrated, but longitudinal and circular mucosal folds could not be visualized. In conclusion, 3D images of the bronchi acquired using helical CT were useful in evaluating endobronchial lesions.     

The master curve and the constitutive equation for creep deformation and fracture for Cr-Mo-V steel throughout smooth,notched and precracked specimens

It has been shown experimentally that the master curve for creep deformation versus the ratio of time to fracture time, can be obtained for smooth, notched and precracked specimens of Cr-Mo-V steel, a high-temperature ductile material. A simple unified constitutive equation, i.e. a master curve equation, has been proposed. It is suggested that there is some correlation between the creep deformation fracture curve and the creep damage size master curve. Although the range of the applicability of methodology might be rather limited, the development of this concept is needed for improved long-term creep lives and for other creep ductile materials.     

Excessive closure of the right eye: a new sign of infarction in the territory of the ipsilateral right middle cerebral artery

In right middle cerebral territory infarction a new sign, excessive closure of the right eye ipsilateral to the lesion and mild closure of the left eye on command, was noted. The excessive ipsilateral eye closure was not observed on spontaneous eye closure.     

Effect of changing groundwater levels caused by land-use changes on greenhouse gas fluxes from tropical peat lands

Monthly measurements of carbon dioxide (CO₂), methane (CH₄) and nitrous oxide (N₂O) fluxes in peat soils were carried out and compared with groundwater level over a year at four sites (drained forest, upland cassava,upland and lowland paddy fields) located in Jambi province, Indonesia. Fluxes from swamp forest soils were also measured once per year as the native state of this investigated area. Land-use change from drained forest to lowland paddy field significantly decreased the CO₂ (from 266 to 30 mg C m^–2 h^–1) and N₂O fluxes (from 25.4 to 3.8 g N m^–2 h^–1), but increased the CH₄ flux (from 0.1 to 4.2 mg C m^–2 h^–1) in the soils. Change from drained forest to cassava field significantly increased N₂O flux (from 25.4 to 62.2 g N m^–2 h^–1), but had no significant influence on CO₂ (from 266 to 200 mg C m^–2 h^–1) and CH₄ fluxes (from 0.1 to 0.3 mg C m^–2 h^–1) in the soils. Averaged CO₂ fluxes in the swamp forests (94 mg C m^–2 h^–1) were estimated to be one-third of that in the drained forest. Groundwater levels of drained forest and upland crop fields had been lowered by drainage ditches while swamp forest and lowland paddy field were flooded, although groundwater levels were also affected by precipitation. Groundwater levels were negatively related to CO₂ flux but positively related to CH₄ flux at all investigation sites. The peak of the N₂O flux was observed at –20 cm of groundwater level. Lowering the groundwater level by 10 cm from the soil surface resulted in a 50 increase in CO₂ emission (from 109.1 to 162.4 mg C m^–2 h^–1) and a 25% decrease in CH₄ emission (from 0.440 to 0.325 mg C m^–2 h^–1) in this study. These results suggest that lowering of groundwater level by the drainage ditches in the peat lands contributes to global warming and devastation of fields. Swamp forest was probably the best land-use management in peat lands to suppress the carbon loss and greenhouse gas emission. Lowland paddy field was a better agricultural system in the peat lands in terms of C sequestration and greenhouse gas emission. Carbon loss from lowland paddy field was one-eighth of that of the other upland crop systems, although the Global Warming Potential was almost the same level as that of the other upland crop systems because of CH₄ emission through rice plants.     

IMPROVEMENT OF TYPE IV CRACKING RESISTANCE OF 9Cr HEAT RESISTING STEEL WELDMENT BY BORON ADDITION

Creep lives of high Cr ferritic heat resisting steel weldments decrease due to Type Ⅳ fracture, which occurs as a result of formation and growth of creep voids and cracks on grain boundaries in fine-grained heat affected zone (HAZ). Because boron is considered to suppress the coarsening of grain boundary precipitates and growth of creep voids, we have investigated the effect of boron addition on the creep properties of 9Cr steel weldments. Four kinds of 9Cr3WSCoVNb steels with boron content varying from 4.7×10-5 to 1.8×10-4 and with nitrogen as low as 2.0×10-5 were prepared. The steel plates were welded by gas tungsten arc welding and crept at 923K. It was found that the microstructures of HAZ were quite different from those of conventional high Cr steels such as P91 and P92, namely the fine-grained HAZ did not exist in the present steel weldments. Boron addition also has the effect to suppress coarsening of grain boundary carbides in HAZ during creep. As a result of these phenomena, the welded join     

Construction of a robot control system which understands a voice and pointing actions

This research was aimed at making a robot that can go and get an object designated by the user. We produced a robot control system that uses pointing and voice control. This control system is composed of two systems. One system is the object instruction system that uses pointing, and the other is the object instruction system that uses voice. The approximate position of a designated object is recognized by the object instruction system that uses pointing, and information about the object and instructions about the operation are conveyed by the object instruction system that uses voice. This time, the object instruction system that uses pointing has been designed and verified as the first step. A calculation resource to calculate the approximate position of the designated object is obtained when the user points directly at the object. A robot can be moved around a designated object by using this system. The object instruction system that uses voice will be constructed in future work.     

Cooperative manipulation of a floating object by some space robots with joint velocity controllers: application of a tracking control method using the transpose of the generalized Jacobian matrix

We have studied the cooperative manipulation of floating object by several space robots. For these cooperative motions, we have reported that a tracking control method using the transpose of the generalized Jacobian matrix (GJM) can be utilized for robots with joint torque controllers. For cooperative motions by some robots with joint velocity controllers, we proposed a tracking control method using the transpose of the GJM. Simulation results show the effectiveness of the proposed control method.     

Evaluation of vector magnetic property in a three-phase induction motor model core with visualization of streamline

In this paper, a streamline display method for magnetic flux density and magnetic field strength vectors in a three-phase induction motor model core is presented, and the relationship between streamlines and magnetic properties is investigated. It is possible to visualize the vector magnetic properties distribution by representing the magnetic flux density and the magnetic field strength vector with the streamlines. In addition, the time variation of the streamlines of the magnetic flux density and magnetic field strength vectors, and magnetic energy was compared. It was clear that the magnetic energy did not necessarily increase in the areas where the magnetic flux density and magnetic field strength increased because these vectors have the spatial phase difference.