Isolation of antimicrobial agent from the marine algae Cystoseira hakodatensis

Cystoseira hakodatensis is an unutilised brown algae belonging to family Sargassaceae. A crude methanol extract from the algae showed inhibitory effects on the growths of Bacillus cereus and Bacillus licheniformis. To isolate the major antimicrobial agent, a sequential active‐guided isolation procedure was applied: liquid–liquid extraction, column chromatography and bio‐autography. A marked antimicrobial agent (active α) was isolated in hydrophobic fraction and was determined to phenolics without carbohydrates and proteins by phytochemical test. Regarding the antimicrobial potential, the isolated active α showed better inhibitory effects against B. cereus and B. licheniformis at 2 and 4 times of lower concentrations (62.5 and 31.3 μg mL^?1) in comparison with epigallocatechin gallate. These results showed that C. hakodatensis is a potential source of antimicrobial agent capable of preventing the growth of the two bacteria.     

Characterization of anisotropic gas permeability and thermomechanical properties of highly textured porous alumina

Porous alumina with a highly textured microstructure was fabricated by pulse electric current sintering (PECS) using alumina platelets. Highly oriented porous alumina with a porosity of 3%–50% was obtained by a pressure-controlled method of PECS. The properties of the highly textured porous alumina were measured in two directions. The nitrogen gas permeance and thermal conductivity at room temperature were higher in the direction along the platelet length due to the higher continuity of pores and the connectivity of alumina platelets, respectively. The anisotropy of the thermal conductivity at room temperature was investigated and explained by the effect of grain size of platelets as well as morphology and orientation of pores. The bending strength was higher with the loading direction along the platelet thickness. The thermal shock strength was clearly different in the two directions. The difference in the thermal shock strength was investigated by the measurement of properties and thermal stress analysis.     

Combustion synthesis of AlN doped with carbon and oxygen

Carbon-and-oxygen-doped AlN specimens were prepared by combustion synthesis using Al, graphite, and AlN. Graphite addition changed the product color from white to blue. By XRD, the lattice constant increased slightly with increasing carbon content. Blue AlN powder was synthesized with a molar ratio of the diluent AlN of 0.2-0.5 with a fixed graphite content of 0.05. At an AlN molar ratio exceeding 0.6, carbon was not successfully incorporated due to the lower reaction temperature. Calcination at 800°C in air removed residual graphite without changing the crystal structure or product color. Oxygen, nitrogen, and carbon analyses revealed that blue AlN powders contained 0.45-0.54 mass% carbon and 1.4-1.6 mass% oxygen, while the undoped AlN contained 0.021 mass% carbon and 0.94 mass% oxygen. The origin of the white-to-blue color change was investigated via reflection measurements. Blue AlN exhibits an absorption peak at 634 nm (1.96 eV). From first-principles electronic structure calculations, the C-doped AlN and carbon-and-oxygen-doped AlN with a 1:1 ratio could be classified as p-type, whereas the O-doped AlN and 1:3 carbon-and-oxygen-doped AlN were n-type. One reason for the absorption peak at 634 nm may be a transition from the conduction band to an upper unoccupied state. These results suggest the possible control of optical and electronic properties of AlN via carbon-and-oxygen doping.     

Aqueous One-pot Synthesis of Glycopolymers by Glycosidase-catalyzed Glycomonomer Synthesis Using 4,6-Dimetoxy Triazinyl Glycoside Followed by Radical Polymerization

Glycopolymers have attracted increased attention as functional polymeric materials, and simple methods for synthesizing glycopolymers remain needed. This paper reports the aqueous one-pot and chemoenzymatic synthesis of four types of glycopolymers via two reactions: the β-galactosidase-catalyzed glycomonomer synthesis using 4,6-dimetoxy triazinyl β-D-galactopyranoside and hydroxy group-containing (meth)acrylamide and (meth)acrylate derivatives as the activated glycosyl donor substrate and as the glycomonomer precursors, respectively, followed by radical copolymerization of the resulting glycomonomer and excess glycomonomer precursor without isolating the glycomonomers. The resulting glycopolymers bearing galactose moieties exhibited specific and strong interactions with the lectin peanut agglutinin as glycoclusters.     

Magnet Safety Assessment for ITER

The ITER magnet system consists of structurally linked sets of toroidal (TF) and poloidal (PF) field coils, central solenoid (CS), and various support structures. The coils are superconducting, force flow Helium cooled with a Kapton-Glass-Epoxy multilayer insulation system. The stored magnetic energy is about 100GJ in the TF system and 20GJ in the PF-CS. Coils and structure are maintained at 4 K by enclosing them in a vacuum cryostat. The cryostat, comprising an outer envelope to the magnets, forms most of the second radioactivity confinement barrier. The inner primary barrier is formed by the vacuum vessel, its ports and their extensions. To keep the machine size within acceptable bounds, it is essential that the magnets are in close proximity to both of the nuclear confinement barriers. The objective of the magnet design is that, although local damage to one of the barriers may occur in very exceptional circumstances, large scale magnet structural or thermal failure leading to simultaneous breaching of both barriers is not credible. Magnet accidents fall into three categories: thermal (which includes arcing arising from insulation failure and local overheating due to discharge failure in the event of a superconductor quench), structural (which includes component mechanical failure arising from material inadequacies, design errors and exceptional force patterns arising from coil shorts or control failures), and fluid (Helium release due to cooling line failure). After a preliminary survey to select initial faults conceivable within the present design, these faults are systematically analyzed to provide an assessment of the damage potential. The results of this damage assessment together with an assessment of the reliability of the monitoring and protective systems, shows that the magnets can operate with the required safety condition.     

A 300-MHz 25-/spl mu/A/Mb-leakage on-chip SRAM module featuring process-variation immunity and low-leakage-active mode for mobile-phone application processor

An on-chip 1-Mb SRAM suitable for embedding in the application processor used in mobile cellular phones was developed. This SRAM supports three operating modes - high-speed active mode, low-leakage low-speed active mode, and standby mode - and uses a subdivisional power-line control (SPC) scheme. The combination of three operating modes and the SPC scheme realizes low-power operation under actual usage conditions. It operates at 300 MHz, with leakage of 25 /spl mu/A/Mb in standby mode, and 50 /spl mu/A/Mb at the low-leakage active mode. This SRAM also uses a self-bias write scheme that decreases of minimum operating voltage by about 100 mV.     

Operation of superconducting fault current limiter using vacuum interrupter driven by electromagnetic repulsion force for commutating switch

Using conventional high‐temperature superconducting wire, a model superconducting fault current limiter (SFCL) is made and tested. Solenoid coil using Bi2223 silver sheath wire is so made that inductance is as small as possible and a vacuum interrupter is connected in series to it. A conventional reactor coil is connected in parallel. When the fault current flows in this equipment, superconducting wire is quenched and current is transferred into the parallel coil because of voltage drop of superconducting wire. This large current in parallel coil actuates magnetic repulsion mechanism of vacuum interrupter. Due to opening of vacuum interrupter, the current in superconducting wire is broken. By using this equipment, current flow time in superconducting wire can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of parallel coil. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 52–61, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20315     

Hydrothermal corrosion of magnesiapartially-stabilized zirconia

Changes in the phase compositions and microstructures of magnesia-partially-stabilized zirconia (Mg-PSZ) were studied in water at 80–300 °C, 1 m HCl solutions at 80–140 °C and 1 m CH₃COOH-CH₃COONa buffer solutions at pH 3 and 80–140 °C for 10–40 days. The tetragonal to monoclinic phase transformation and the degradation of the fracture strength occurred in water above 200 °C. On the other hand, although no noticeable tetragonal to monoclinic phase transformation proceeded in 1 m HCl solutions and 1 m CH₃COOH-CH₃-COONa buffer solutions at pH 3 below 140 °C, the fracture strength of Mg-PSZ greatly degraded. The dissolution of Mg²⁺ ion was observed in water above 200 °C and in 1 m HCl solutions above 80 °C.     

Amyloid beta-protein deposition in the leptomeninges and cerebral cortex

To further investigate the process of amyloid beta-protein (Abeta) deposition, we determined, using sensitive enzyme immunoassays, the levels of Abeta40 and Abeta42 (Abetas) in the soluble and insoluble fractions of the leptomeninges (containing arachnoid mater and leptomeningeal vessels) and cerebral cortices from elderly control subjects showing various stages of Abeta deposition and from patients affected by Alzheimer's disease (AD). In both locations, insoluble Abeta levels were higher by orders of magnitude than soluble Abeta levels. Soluble Abeta levels in cortices were much lower than those in leptomeninges. In insoluble Abeta in the cortex, Abeta42 was by far the predominant species, and Abeta42 in AD cortices was characterized by the highest degree of modifications in the amino terminus. In contrast, this Abeta42 predominance was not observed in insoluble Abeta in the leptomeninges, which were found to be able to accumulate Abetas to an extent similar to that in the cortex, on a weight basis. The levels of insoluble Abeta in the leptomeninges or cortex generally correlated with the degree of cerebral amyloid angiopathy or the abundance of senile plaque, respectively. However, the presence of plaque-free cortical samples showing significant levels of insoluble Abeta42 suggests that biochemically detectable Abeta accumulation precedes immunocytochemically detectable Abeta deposition in the cortex.