Transmittance and cathodoluminescence of AlN ceramics sintered with Ca3Al2O6 as sintering additive

Aluminum nitride ceramics were prepared by sintering with 0–4.8 mass% of Ca₃Al₂O₆ (C₃A) as a sintering additive. The transmittance in the range of 260–550 nm increased with increasing amount of C₃A. The cathodoluminescence intensity attributed to oxygen-induced defects decreased with increasing amount of C₃A. From the results, the increase of the transmittance in the range of 260–550 nm was considered to be related to the decrease of the oxygen-induced defect density.     

Establishment time of liquid flow in a bath agitated by bottom gas injection

The establishment time of gas-liquid two-phase flows in a cylindrical bath agitated by bottom gas injection through a central single-hole bottom nozzle was investigated. Because the turbulence intensity in the bath was comparable to or larger than the unity, the conventional definition of the flow establishment time based on the history of mean velocity was not suitable for the present case. In fact, it was difficult to determine the flow establishment time based on the well-known 90 or 99 pct criterion for the mean velocity. Accordingly, two methods of determining the flow establishment time by focusing on the turbulence components instead of the mean velocity components were proposed. Velocity measurements were made with a two-channel laser Doppler velocimeter. The flow establishment time was correlated as a function of gas flow rate. Close agreement was obtained by the two methods.     

A demonstrative study for the wind and solar hybrid power system

In March 1995, a small scale wind and solar hybrid power system was installed at Ashikaga Institute of Technology. Until now, the authors have acquired the data of the output of the hybrid power plant along with wind speed, wind direction, and the solar radiation, in order to demonstrate a complementary relationship between solar energy and wind energy.After nine months operation of the system, the authors confirmed that there exists a complementary relationship between solar energy and wind energy. We also found, however, that the power output by wind does not have much prospect compared to that by solar cell especially in summer season in Ashikaga area.     

Dyeing properties of oxygen low-temperature plasma-treated wool and nylon 6 fibres with acid and basic dyes

Wool and nylon 6 fibres treated with oxygen low-temperature plasma were dyed with acid and basic dyes. Despite the increase of electronegativity of the fibre surface caused by the plasma treatment, the rate of dyeing of wool was increased with both dyes, while that of nylon 6 was decreased with the acid dye and increased with the basic dye.     

Changes in Aging Behavior and Defect Structure of Yttria-Fully-Stabilized ZrO2 with Sc2O3 Doping

Methods of suppressing decreased conductivity in 8 mol% Y₂O₃-stabilized–92 mol% ZrO₂ (8YSZ) with aging were investigated. Different amounts of Sc₂O₃ were doped into 8YSZ. The electrochemical properties of Sc₂O₃-doped 8YSZ were measured, and the microstructural and local structural changes were characterized. The present results indicate that an appropriate amount of Sc₂O₃ doping, 3 or 4 mol%, effectively suppresses decreased conductivity with aging in 8YSZ.     

CUDA programs for the GPU computing of the Swendsen–Wang multi-cluster spin flip algorithm: 2D and 3D Ising,Potts, and XY models

We present sample CUDA programs for the GPU computing of the Swendsen–Wang multi-cluster spin flip algorithm. We deal with the classical spin models; the Ising model, the q$q$-state Potts model, and the classical XY model. As for the lattice, both the 2D (square) lattice and the 3D (simple cubic) lattice are treated. We already reported the idea of the GPU implementation for 2D models (Komura and Okabe, 2012). We here explain the details of sample programs, and discuss the performance of the present GPU implementation for the 3D Ising and XY models. We also show the calculated results of the moment ratio for these models, and discuss phase transitions.     

Topology optimization for fluid–thermal interaction problems under constant input power

This paper deals with density-based topology optimization considering fluid and thermal interactions, in which the Navier–Stokes and heat transport equations are coupled. We particularly focus on designing heat exchangers. In the engineering context, heat exchangers are designed while considering a certain amount of input power. Therefore it is important to maximize the performance of a heat exchanger under a constant input power. In this paper we propose a way to control the input power by introducing an extra integral equation. To be more precise, in the fluid analysis, the inlet pressure is determined by solving the extra integral equation together with the Navier–Stokes equation. By doing this we can keep the inlet power constant even when the flow channels are changed in the optimization process. Consequently, the system of equations of the fluid field takes an integrodifferential form. On the other hand, in the heat transport analysis, a single governing equation is defined for simultaneously modeling both the solid and fluid parts. The design variable is a fluid fraction whose distribution represents the topology of the solid and fluid domains. When designing heat exchangers, two different heat conditions are considered in the formulation of the optimization problems, namely temperature-dependent and temperature-independent heat sources. Through the numerical examples for designing flow channels in a heat exchanger, it is shown that distinct topologies can be obtained according to the input power and the heat source conditions.     

A novel radial orientation treatment of nematic liquid crystals using magnetic field lines with permanent magnet and applying the assisted electric field

Recently, there has been considerable research on optical devices, such as liquid crystal (LC) lenses and special optical plates, using LCs. In such devices, relatively small LC cells are frequently used, or unique LC orientations are required. As an LC orientation process, we focused on the LC director's orientation induced by the magnetic force line distribution of a small neodymium magnet. We propose a simple method for obtaining radial orientation, which is rather difficult to obtain using the ordinary rubbing method. The initial orientation in the LC cell is a vertical orientation cell with almost zero azimuth anchoring. With the proposed method, the reorientation process is performed with an assisting electric field and a small permanent magnet, unlike the conventional magnetic field orientation process that requires a large electromagnet. Furthermore, a polymer stabilization treatment is used to fix the obtained radial orientation pattern in the LC cell. After the treatment, the applying voltage can control the tilt angle of the director in weak polymer treatment, and a completely fixed orientation pattern can be obtained that in strong.     

Triglyceride analysis by combined argentation/nonaqueous reversed phase high performance liquid chromatography

Full analysis of triglycerides of natural fats and oils has been investigated by the combination of argentation high performance liquid chromatography (HPLC) with nonaqueous reversed phase (NARP) HPLC. An infrared detector was used in argentation HPLC, because it indicated molar responsibility to all triglycerides. After peak trapping with argentation HPLC, each triglyceride fraction was analyzed with NARP chromatography using the glyceride-selective post-column reactor detector. The results of the analyses of triglycerides of palm oil and cocoa butter by the proposed method agreed well with those reported earlier.     

Fabrication of nanoscale tungsten tip arrays for scanning probemicroscopy-based devices

A new fabrication process for nanoscale tungsten tip arrays was developed for scanning probe microscopy-based devices. It is suitable to make a huge array on a device chip and is potentially compatible with CMOS technology. In this study, tungsten was selected as a tip material because of its hardness and conductivity. The newly developed fabrication process mainly consists of several important techniques: a combination of optical lithography and electron beam (EB) lithography to reduce the total exposure time with high resolution and chromium/tungsten/chromium (Cr/W/Cr) sandwich deposition and etching in which the first chromium layer is used as a mask and a second one is used as an etch stop. A periodic array of dots in an EB resist with a spot diameter of less than 50 nm was obtained by a combination of optical lithography and EB lithography with a positive resist (polymethylmethacrylate) in which all processing conditions were optimized carefully. A thin and uniform chromium film, deposited by ion-beam sputtering, allowed the use of thin polymethylmethacrylate (PMMA) film which led to the high resolution. The conditions of dc magnetron sputtering were also optimized in order to deposit a densely packed and low-resistivity film. The resulting tungsten tip arrays had a cylindrical shape with diameters of less than 60 nm and heights of 300 nm