Transmittance and cathodoluminescence of AlN ceramics sintered with Ca3Al2O6 as sintering additive

Aluminum nitride ceramics were prepared by sintering with 0–4.8 mass% of Ca₃Al₂O₆ (C₃A) as a sintering additive. The transmittance in the range of 260–550 nm increased with increasing amount of C₃A. The cathodoluminescence intensity attributed to oxygen-induced defects decreased with increasing amount of C₃A. From the results, the increase of the transmittance in the range of 260–550 nm was considered to be related to the decrease of the oxygen-induced defect density.     

Time-dependent deformation in an enhanced SiC/SiC composite

Time-dependent deformation in an enhanced SiC/SiC composite has been studied under constant load at high temperatures of 1200 °C, 1300 °C, and 1400 °C. Creep damage evolution was evaluated by a Young’s-modulus change of partial unloading and microscopic observation. The addition of the glassy phase in the matrix is very effective for protecting the composite from oxidation. The transient creep is dominant in creep life at all the temperatures. An empirical equation is proposed to describe creep behavior of the composite. It is found that creep activation energy increases with creep time at stresses lower than matrix cracking stress, but the activation energy remains constant at stresses higher than the matrix cracking stress. The creep strain rate of the composite is considered to be controlled by creep of fibers based on examining the time, strain, stress, and temperature dependencies of creep strain rates.     

Radiation tolerance for the SMASH-series front-end chips for a silicon micro-strip detector

The radiation tolerance for prototype front-end chips designed for a silicon micro-strip detector was examined with a ⁶⁰Co irradiation source to establish an allowable range of the radiation dose. The irradiated front-end chips were SMA²SH-64A, a 64-channel preamplifier array; SMA²SH-1, a single-channel preamplifier circuit with a comparator; and Control-C, a digital-control chip for the preamplifiers.     

Effective thermal conductivity of compressed woods

Compression is one solution to improve the strength of softwoods. The effective thermal conductivities of compressed Japanese cedars (cryptomeria japonica), which were compressed in the radial direction of the wood, were measured. Both the effective thermal conductivities in the tangential and fiber directions increase proportionally to the density increment due to the compression. However, the thermal conductivity in the radial direction (compression direction) increases slightly with the density increment. Numerical computations were conducted to explain the characteristics of thermal conductivity in the radial direction by using a microscopic heat conduction model for the compressed wood. The numerical results were compared with the measured values. And the physical mechanism of the heat conduction in the compressed woods is discussed.     

Development of a single loop EPR test method and its relation to grain boundary microchemistry for alloy 600

A single loop electrochemical potentiokinetic reactivation test method has been developed for alloy 600 that produces good passivation on all the surfaces, good etching during the reactivation scan and no appreciable pitting. It is able to quantify and discriminate between samples with a wide range of degree of sensitization. The Pa value correlates well with the minimum level of chromium in the depletion regions at the grain boundaries. It has been shown that the width of the attacked regions is much larger than the width of chromium depletion regions and it does not show any direct correlation with either depth or width or with a volume parameter of chromium depletion regions. It has been shown that the chromium carbides are not attacked during the test and that the intragranular regions attacked during the test are the sites of chromium carbides in the grain matrix. A modified Pa parameter is shown to be sensitive down to 7.5 wt% chromium in the depletion regions and indicates that the intragranular carbides have shallower depletion profiles than those at grain boundaries. Comparison of the results of the single loop and the double loop tests showed a good correlation.     

Recovery retardation in equal channel angular pressed Al–Zr alloy during friction stir welding

The effect of Zr on reduction of hardness and microstructure in an FS weld of equal channel angular-pressed Al alloy was investigated. Zr addition to Al suppressed dynamic recovery in the thermomechanically affected zone and enabled retention of the high hardness of the ECA-pressed material throughout the weld.     

Pulsed KrF excimer laser annealing of silicon solar cell

The pulsed KrF excimer laser annealing of silicon films for solar cell with EBEP-CVD and LP-CVD was studied theoretically and experimentally. Three-dimensional thermal diffusion equation for microcrystalline and amorphous silicon was solved by using the finite difference methods. The results of our heat-flow simulation of laser re-crystallization in a laser irradiation with 50 ns pulse duration almost agree with the experimental results in re-crystallization depth of 0.7 μm for microcrystalline silicon (EBEP-CVD) and 0.4 μm for amorphous silicon (LP-CVD) in a single pulse excimer laser annealing.     

The heat transfer and pressure drop characteristics of finned tube banks in forced convection (effects of fin height on pressure drop characteristics)

In recent years the requirement for the reduction of energy consumption has been increasing to solve the problems of global warming and the shortage of petroleum resources. For example, in the power generation field, as thermal power generation occupied 60% of the power generation demand, considerable improvement of the thermal efficiency is required. This paper describes the pressure drop characteristics of finned tube banks used for heat exchangers in thermal power generation that were clarified by testing serrated finned tube banks with different fin heights for improved heat transfer and conventional spiral finned tube banks with different fin heights, and an equation to predict pressure drop which is necessary for the heat exchanger design is proposed. © 2006 Wiley Periodicals, Inc. Heat Trans Asian Res, 35(3): 179–193, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20112     

Augmentation by phthalimides of phorbol ester-induced expression of tumor necrosis factor alpha message

N(alpha)-Phthalimidoglutarimide (thalidomide), 2-(2,6-diisopropylphenyl)-1H-isoindole-1,3-dione (PP-33) and its 4,5,6,7-tetrafluoro derivative (FPP-33) augmented 12-O-tetradecanoylphorbol 13-acetate-induced production by human leukemia HL-60 cells of both tumor necrosis factor alpha (TNF-alpha) mRNA and secreted TNF-alpha protein. Intracellular TNF-alpha protein production was increased to a lesser extent.