Hierarchical micro-nanostructured albite-based glass-ceramic for high dielectric strength insulators

A novel glass-ceramic material based on albite type Na-rich feldspar has been synthesized by conventional ceramic process. High crystallinity, >94%?Vol.% is obtained by fast sintering which allows energy saving processing. Albite is the main crystalline phase and tetragonal SiO₂ is a secondary phase. Electrical properties were examined by complex impedance, DC measurements, and dielectric breakdown test. Dielectric characterization shows a non-Debye type dielectric behavior with low dielectric constant, 4.6 at 1?MHz, low dielectric losses, (～10^?3 at 1?MHz, and a large dielectric strength, ～60?kV/mm), that it is the largest value reported in ceramic insulators. Those dielectric properties are attained by the low glassy phase content in the samples and their unique micro-nanostructure. All these properties make this novel material a very promising candidate in the market of ceramic electrical insulator, highlighting for high-voltage applications.     

Hydrogen adsorption studies in micro-size cobalt dots

Hydrogen desorption curves were obtained from a sample composed of a square arrangement of Co dots with average diameter of 4.4 μm, separated by a distance of 11.6 μm. A macroscopic sample of Co dots grown on a 2.5 × 2.5 cm Si substrate was made by standard lithographic techniques and used in these experiments. Thermal programmed desorption (TPD) was performed under ultra-high vacuum conditions. Hydrogen TPD curves were obtained from a 1 × 1 cm Co dots samples displaying a maximum of intensity at 425 K. Hydrogen TPD curve was also obtained from 1 cm× 1 cm samples of Co films and Co foils for comparison. The hydrogen TPD curves have decreasing intensity from the Co foils to the Co dots and finally to the Co films. This indicates that there are more sites for hydrogen adsorption on the Co dots than in the Co films. This is a surprising result because there is approximately 8.7 times less Co atoms exposed in the Co dots that in the Co film sample. A desorption energy of 27 kcal/mol was obtained for the Co dots suggesting that hydrogen is adsorbed on an hcp hollow site of the Co dot crystalline structure.     

Using ion implantation to adjust the transition temperature of superconducting films

We summarize a continuing investigation into using ion implantation to alter the transition temperature of superconducting thin films. The primary motivation for the work presented here was to study the feasibility of using magnetic ion doping to replace the bi-layer T_c control process currently used for certain cryogenic detector applications at National Institute for Standards and Technology. The results from work with various ion species implanted into aluminum, molybdenum, titanium and tungsten host films are presented.     

A scale model for fitting object shapes from fixed location data

In this paper we present a scale model for fitting an ideal shape to an object. The measurements of the object are taken corresponding to a fixed coordinate system at a set of well-defined locations on the surface of the object. We propose an algorithm to estimate the model parameters and hypothesis tests to make statistical inferences about several possible special cases of the general model. The model is tested with an example that analyzes data on the feet of people in Hong Kong.     

RBS/channelling study of ion-implanted and proton-exchanged LiNbO3:Nd:MgO planar waveguides

We present a structural study of two Nd³⁺/MgO codoped LiNbO₃ waveguides fabricated by two different methods: ion-implantation and proton-exchange. Rutherford backscattering spectrometry in combination with channelling was used to study the influence of the waveguide fabrication method on the possible modification of the LiNbO₃ crystal structure within the waveguiding layer. The results show that the ion-implanted waveguide mainly maintains the same properties as the virgin crystal, apart from a deterioration of a thin surface layer, whilst the proton-exchanged waveguide exhibits a quite different behaviour, although its surface is less damaged.     

A zero-voltage and zero-current switching three-level DC/DC converter

This paper presents a novel zero-voltage and zero-current switching (ZVZCS) three-level DC/DC converter. This converter overcomes the drawbacks presented by the conventional zero-voltage switching (ZVS) three-level converter, such as high circulating energy, severe parasitic ringing on the rectifier diodes, and limited ZVS load range for the inner switches. The converter presented in this paper uses a phase-shift control with a flying capacitor in the primary side to achieve ZVS for the outer switches. Additionally, the converter uses an auxiliary circuit to reset the primary current during the freewheeling stage to achieve zero-current switching (ZCS) for the inner switches. The principle of operation and the DC characteristics of the new converter are analyzed and verified on a 6 kW, 100 kHz experimental prototype.     

Sheet molding compound characterization using spiral flow

Sheet molding compound (SMC) is a fiber‐reinforced polymeric composite. It is often used in automotive, marine, and industrial applications over other materials because of its high strength to density ratio, resistance to corrosion, and low cost. There is a demand in the SMC industry to be able to characterize SMC processability. This is particularly true for heavy truck body panels, one of the fastest growing applications of SMC. Because of their large size and high strength requirement, the molding forces have a major influence in the molding cycle. Also because of the long flow paths involved, the ability of the paste to carry glass needs to be properly characterized when developing new SMC materials. In this article, we demonstrate the benefits of using spiral flow as a processability tester. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Rates of reinfection with Echinococcus granulosus, Taenia hydatigena, taenia ovis and other cestodes in a rural dog population in Uruguay

Forced thinking is an incompletely understood and rarely described epileptic aura. We studied three patients with forced thinking from left frontal lesions, two neoplastic and one vascular. All three experienced repetitive, intrusive thoughts at the onset of seizures. Their forced thinking was associated with the desire to vocalize, orobuccal movements, and speech arrest. The episodes occurred with other ictal manifestations and responded to antiseizure therapy. These patients suggest that epileptic forced thinking is a heterogeneous phenomenon; forced thinking from left frontal lesions is a manifestation of expressive language and is distinct from experiential thoughts arising from temporal limbic foci.     

New species of Aeromonas isolated in Cuba

One hundred and fifty-five strains of Aeromonas isolated in the stools of children under 5 years presenting with acute diarrheal disease were studied. Using the Aerokey II system for the identification of species, 47 strains were identified as Aeromonas caviae, 58 as Aeromonas hydrophila, 23 as Aeromonas veronii biovar sobria, 14 as Aeromonas trota, 9 as Aeromonas veronii biovar veronii, 2 as Aeromonas jandaei and 2 as Aeromonas shubertii, Emphasis is placed on the advantages of this method which allowed for the classification of new species not identified previously in our country.