基于FPGA和ARM的弹上相位自动微调控制器设计与实现

为了提高相位自动微调控制器的控制性能,针对某型导弹,提出并实现了以ARM+ FPGA双微处理器为核心的硬件设计方案,采用了模糊PID控制算法,通过优化步进电机控制模式,提高了相位自动微调控制器的控制精度,将步进电机的调整时间由800 ms缩短到100 ms以内;该方案已成功应用于某型弹上系统,实践证明,该设计方案成本低、可扩展性强,能够满足系统控制需求,具有较高的实用性,大大提高了装备维护效率.     

旋压变形数值模拟中局部加载卸载问题的处理

此文介绍了旋压加工数值模拟中遇到的局部加载卸载问题的处理方法，并对筒形件强力旋压过程进行了数值模拟，求得了变形区应变的分布，理论计算结果与变形实际和实测结果完全吻合。     

三维刚塑性有限元法中摩擦边界条件的处理方法

介绍了三维刚塑性有限元法中摩擦边界条件中处理方法，给出了相应的计算公式。     

筒形件正旋旋压力有限元计算及分析

采用三维刚塑性有限元法计算了筒形件正旋时的旋压力，并对各工艺参数对旋压力的影响进行了系统研究。     

Flow behavior and microstructure evolution during hot compression of TA 15 titanium alloy

The samples of TAI 5 titanium alloy were hot compressed in the temperature range of 550-1 000 β at constant strain rate from 0.01 s^-1 to 1.0 s^-1. The flow behavior and microstructural evolution during hot deformation of TA 15 alloy were investigated, based on which the hot working parameters of TA15 alloy were selected. The results show that with the increase of deformation temperature and decrease of stain rate, the flow stress decreases gradually, but the magnitude of stress drop varies with the increase of temperature in different temperature intervals. According to the flow stress and deformation microstructure, the deformation behavior can be classified into three types as working hardening（550-600 β, α＋β phase）, dynamic recrystallization （650-900 ℃, α＋β phase） and dynamic recovery（950-1 000 ℃, β phase）. The main softening mechanism is dynamic recrystallization（DRX） of a phase in α＋β phase zone and dynamic recovery（DRV） of β phase in β phase zone. As the stain rate decreases dynamic recrystallization of a phase proceeds more adequately in α＋β zone and the β subgrains of dynamic recovery have the tendency to grow infl zone. The reasonable temperature for warm forming of TA15 alloy is in the range of 600-700 , which has been verified by warm spinning experiment of tube workpieces.：     

热变形参数对Ti-15-3合金显微组织的影响及预测

通过等温压缩试验和金相分析研究了热变形参数对Ti-15-3(Ti-15V-3Cr-3Sn-3Al）合金固溶处理后显微组织的影响，等效晶粒尺寸随变形温度升高而增大，随变形程度和变形速率增加而减小，再结晶程度随变形温度升高而减小，随变形程度和变形速率增加而增大，采用人工神经网络的方法建立了等效晶粒尺寸及再结晶晶粒体积百分数与变形程度，变形速率和变形温度间的数学模型，预测值与实测值吻合较好，表明该方法很好地预测热变形参数对Ti-15-3合金固溶处理后显微组织的影响。     

Hydrogen-induced hot workability in Ti-6Al-4V alloy

The effect of hydrogen on hot deformability of Ti-6Al-4V alloy was investigated by isothermal hot compression test with temperature of 800 ℃ and velocity of 0.1 mm/s. By optical microscopy （OM） and transmission electron microscopy （TEM）, the influence of hydrogen on the microstructural features was systematically examined including the morphology of a grain, volume fraction of a phase and dynamic recrystallization （DRX）. The flow stress shows an initial decrease but a later increase with the increase of hydrogen content. The minimum of peak compression flow stress is obtained when 0.2% hydrogen is added into the alloy. The hydrogen-induced softening of Ti-6Al-4V alloy may be that hydrogen induces the increase of proportion of soft β phase, the increase of DRX and the increase of extent of twins.     

逆M序列在机抖激光陀螺消除动态闭锁中的应用

对逆M序列在消除激光陀螺动态闭锁误差中的应用进行了研究和验证.目前多采用M序列对抖动的幅度进行调制来消除激光陀螺动态闭锁误差,而逆M序列与M序列相比不仅满足注入到激光陀螺抖动中的要求,且比M序列有其性质等方面优势.通过理论分析及M序列和逆M序列在消除机抖激光陀螺动态闭锁中实验中的应用对比,实验数据表明逆M序列在消除动态闭锁中的作用要优于M序列.     

中国氦冷固态增殖剂实验包层模块材料研究进展

在未来核聚变反应堆中,为补充氚的消耗,需要在核聚变堆的包层中进行氚的在线增殖,以维持核聚变反应的持续进行。为验证这一关键技术,在国际热核聚变实验堆（ITER）上开展了ITER TBM计划（实验包层项目）。作为ITER计划成员方之一,中方以中国氦冷固态增殖剂实验包层模块（HCCB TBM）概念参与ITER TBM计划。HCCB TBM现今进入初步设计阶段,而材料的制备技术和性能数据是支撑其结构设计、安全分析和服役工况评估的基础。本文综述和分析了HCCB TBM结构材料低活化铁素体/马氏体钢（RAFM钢）与功能材料氚增殖剂和中子倍增剂的研究现状,并对这些材料下一步的研究方向进行了展望。