On global Hessenberg based methods for solving Sylvester matrix equations

In the first part of this paper, we investigate the use of Hessenberg-based methods for solving the Sylvester matrix equation $AX+XB=C$. To achieve this goal, the Sylvester form of the global generalized Hessenberg process is presented. Using this process, different methods based on a Petrov–Galerkin or on a minimal norm condition are derived. In the second part, we focus on the SGl-CMRH method which is based on the Sylvester form of the Hessenberg process with pivoting strategy combined with a minimal norm condition. In order to accelerate the SGl-CMRH method, a preconditioned framework of this method is also considered. It includes both fixed and flexible variants of the SGl-CMRH method. Moreover, the connection between the flexible preconditioned SGl-CMRH method and the fixed one is studied and some upper bounds for the residual norm are obtained. In particular, application of the obtained theoretical results is investigated for the special case of solving linear systems of equations with several right-hand sides. Finally, some numerical experiments are given in order to evaluate the effectiveness of the proposed methods.     

Role of Nd-Ni on structural,spectral and dielectric properties of strontium-barium based nano-sized X-type ferrites

The influence of neodymium and nickel substitution on structural and dielectric parameters was investigated in strontium-barium X-type hexagonal ferrites having composition SrBaCu_2?xNi_xNd_yFe_28?yO₄₆ (x = 0, 0.2, 0.4, 0.6, 0.8, 1 and y = 0, 0.02, 0.04, 0.06, 0.08, 0.1). Sol-gel method was employed for synthesizing these hexagonal ferrites. The XRD plots of all studied materials which were annealed at 1250 °C show single phase characteristics. Lattice parameter ‘c’ increased as a consequence of larger radius of rare earth ion (Nd³⁺) as compared to (Fe³⁺), while lattice parameter ‘a’ showed very small variation. The cell volume was obtained in the range 2508.32–2523.75 (ų). The inclusion of Nd-Ni also affected X-ray density, bulk density and porosity. The FTIR spectroscopy indicated the particular absorption peaks of hexagonal ferrites and it was performed in the range of 500–700 cm^?1. On account of Nd-Ni doping, the dielectric constant, dielectric loss and AC-conductivity showed decreasing trend. The occupancy of Nd³⁺ ions at octahedral site impedes the valence alternation of Fe³⁺; therefore there was decrease in dielectric permittivity. Ac conductivity has been decreased from 9.14 to 6.49 (Ω cm)^?1 at frequency of 2.7 GHz. The Cole-Cole plots of synthesized materials noticeably revealed grain boundary contribution. The appearance of single semi-circle in impedance Cole-Cole graphs confirms the exceptional role of grain boundaries in the conduction process. The considerably lower dielectric parameters of investigated nano X-type ferrites propose their feasibility for high-frequency applications (phase shifters, dielectric resonators, stealth technology etc).     

Bond graph modeling,design and experimental validation of a photovoltaic/fuel cell/ electrolyzer/battery hybrid power system

This work presents a complete bond graph modeling of a hybrid photovoltaic-fuel cell-electrolyzer-battery system. These are multi-physics models that will take into account the influence of temperature on the electrochemical parameters. A bond graph modeling of the electrical dynamics of each source will be introduced. The bond graph models were developed to highlight the multi-physics aspect describing the interaction between hydraulic, thermal, electrochemical, thermodynamic, and electrical fields. This will involve using the most generic modeling approach possible for managing the energy flows of the system while taking into account the viability of the system. Another point treated in this work is to propose. In this work, a new strategy for the power flow management of the studied system has been proposed. This strategy aims to improve the overall efficiency of the studied system by optimizing the decisions made when starting and stopping the fuel cell and the electrolyzer. It was verified that the simulation results of the proposed system, when compared to simulation results presented in the literature, that the hydrogen demand is increased by an average of 8%. The developed management algorithm allows reducing the fuel cell degradation by 87% and the electrolyzer degradation by 65%. As for the operating time of the electrolyzer, an increment of 65% was achieved, thus improving the quality of the produced hydrogen. The Fuel Cell's running time has been decreased by 59%. With the ambition to validate the models proposed and the associated commands, the development of this study gave rise to the creation of an experimental platform. Using this high-performance experimental platform, experimental tests were carried out and the results obtained are compared with those obtained by simulation under the same metrological conditions.     

Ballistic behavior of plain and reinforced concrete slabs under high velocity impact

This work presents a numerical simulation of ballistic penetration and high velocity impact behavior of plain and reinforced concrete slabs. In this paper, we focus on the comparison of the performance of the plain and reinforced concrete slabs of unconfined compressive strength 41 MPa under ballistic impact. The concrete slab has dimensions of 675 mm × 675 mm × 200 mm, and is meshed with 8-node hexahedron solid elements in the impact and outer zones. The ogive-nosed projectile is considered as rigid element that has a mass of 0.386 kg and a length of 152 mm. The applied velocities vary between 540 and 731 m/s. 6 mm of steel reinforcement bars were used in the reinforced concrete slabs. The constitutive material modeling of the concrete and steel reinforcement bars was performed using the Johnson-Holmquist-2 damage and the Johnson-Cook plasticity material models, respectively. The analysis was conducted using the commercial finite element package Abaqus/Explicit. Damage diameters and residual velocities obtained by the numerical model were compared with the experimental results and effect of steel reinforcement and projectile diameter were studies. The validation showed good agreement between the numerical and experimental results. The added steel reinforcements to the concrete samples were found efficient in terms of ballistic resistance comparing to the plain concrete sample.     

Extending orthogonal block codes with partial feedback

During the last few years a number of space-time block codes have been proposed for use in multiple transmit antennas systems. We propose a method to extend any space-time code constructed for m transmit antennas to m p transmit antennas through group-coherent codes (GCCs). GCCs make use of very limited feedback from the receiver (as low as 1 bit). In particular the scheme can be used to extend any orthogonal code (e.g., Alamouti code) to more than two antennas while preserving low decoding complexity, full diversity benefits, and full data rate.     

Design and Implementation of a Flexible Manufacturing Control System Using Neural Network

Design and implementation of a sequential controller based on the concept of artificial neural networks for a flexible manufacturing system are presented. The recurrent neural network (RNN) type is used for such a purpose. Contrary to the programmable controller, an RNN-based sequential controller is based on a definite mathematical model rather than depending on experience and trial and error techniques. The proposed controller is also more flexible because it is not limited by the restrictions of the finite state automata theory. Adequate guidelines of how to construct an RNN-based sequential controller are presented. These guidelines are applied to different case studies. The proposed controller is tested by simulations and real-time experiments. These tests prove the successfulness of the proposed controller performances. Theoretical as well as experimental results are presented and discussed indicating that the proposed design procedure using Elman's RNN can be effective in designing a sequential controller for event-based type manufacturing systems. In addition, the simulation results assure the effectiveness of the proposed controller to outperform the effect of noisy inputs.     

Crystallization of amorphous Ni60 Nb40−x Cr x alloys

Crystallization behaviour of amorphous Ni₆₀ Nb_40-x Cr _x (x = 0, 5, 10 and 13 at%) alloys was studied by differential Scanning calorimetry and X-ray diffraction measurements. It is shown that the addition of chromium reduces the crystallization temperature, stages of crystallization and activation energies associated with the crystallization sages of the Ni₆₀Nb₄₀ glass. Crystallization of the Ni₆₀Nb₄₀ glass occurred in three stages; in the initial stage a metastable M-phase formed in the amorphous matrix as reported earlier [1] . However, contrary to earlier observation [1], M -phase was not very stable and transformed together with some amorphous phase to the equilibrium Ni₃Nb phase in the second stage of crystallization. In the third stage, the remaining amorphous matrix transformed to the equilibrium NiNb phase. On addition of chromium the formation/stability of the M-phase was found to be suppressed and equilibrium NbCr₂ phase precipitated preferentially in the first stage. The second stage, corresponding to the formation of Ni₃Nb phase, remained almost unaltered. The third stage corresponding to the crystallization of NiNb phase disappeared completely at 13 at% Cr. In the fully crystallized samples the proportion of the NiNb phase decreased and that of NbCr₂ phase increased continuously with chromium concentration.     

The coating of cadmium compounds with copper compounds

Fine particles of cadmium carbonate (CdCO₃) were prepared by heating aqueous solutions containing dissolved urea and cadmium sulfate at 85°C for 1 h. Effect of the composition of the reactant mixture on the morphology of the precipitated particles was investigated. It was found that the cadmium sulfate content of the reactant mixture significantly affected the shape and size of the precipitated particles. At certain range of reactant mixture composition, cauliflower-shaped uniform particles were obtained. The later particles were coated with basic copper carbonate (Cu₂(OH)₂CO₃) by heating aqueous dispersions, containing CdCO₃ particles, copper (II) nitrate, and urea at 85°C for various periods of time with constant stirring. The coating process was found sensitive to the experimental conditions and in most of the trials; mixtures of the coated and coating precursor particles were obtained. As such, extensive optimizations were carried out and conditions were established for the production of uniformly coated particles.On calcination at 700°C for 1 h, the CdCO₃ particles converted into CdO, whereas the coated particles (CdCO_{3 (core)}/Cu₂(OH)₂CO_{3 (coating)} transformed into CdO_(core)/CuO_(coating)) without sintering. In the coated particles, the core and coating materials stayed mutually inert during the calcination reaction and independently converted into their respective oxides.All the calcined and uncalcined products were characterized by various physical and chemical methods.     

Quasi-static and dynamic crushing behaviors of aluminum and steel tubes with a cutout

Tubular members are commonly used as an energy absorber in engineering structures and many such members have a cutout. In this study, the crushing behaviors of tubes with a cutout are characterized and the effects of cutout on the energy absorption capabilities of these tubes are quantified. Systematic parametric studies were carried out to study the effect of material properties, including yield and ultimate strength of material, strain rate effect, location of cutout, tube length and impact speed on the crushing behaviors and energy absorption capacity of aluminum and steel tubes. First, a numerical model was constructed with a commercial explicit finite element code. It will be first proven that the numerical simulation can produce sufficiently accurate results in an economic manner. Subsequently, the crushing behavior of aluminum and steel tubes with a cutout was experimentally characterized and their energy absorption capacity was evaluated in terms of mean crushing force, peak crushing force and specific energy absorption (SEA). Tubes of various lengths with a cutout located at different locations, subject to both quasi-static and dynamic impact loadings were considered. For steel tubes, the numerical simulation investigated the influence of the strain rate effect and variation in strain hardening ratio of the material. Empirical equations describing the mean and peak crushing forces of aluminum and steel tubes with a cutout were developed using linear and nonlinear regression methods applied to the results obtained from the numerical and experimental studies.     

The effect of biphasic waveform tilt in transvenous atrial defibrillation

Atrial defibrillation can be accomplished using low energy shocks and transvenous catheters. The biphasic waveform tilt required to achieve optimal atrial defibrillation thresholds (ADFTs) is, however, not known. The effect of single capacitor biphasic waveform tilt modification on ADFT was assessed in 20 patients. Following AF induction the defibrillation pulses were delivered between the catheters positioned in the coronary sinus and the right atrium. The single capacitor biphasic waveform shocks, delivered over the same pathways, consisted of 65% tilt (65/65 biphasic waveform) to produce an overall tilt of 88%, or 50% tilt (50/50 biphasic waveform) to produce an overall tilt of 75%. Although 65/65 biphasic waveform delivers more energy, the shorter duration 50/50 biphasic waveform reduced stored energy ADFT 21%, from 1.34 +/- 0.82 J with 65/65 biphasic to 1.06 +/- 0.81 J. These differences were not statistically significant. Nine patients had lower ADFT with 50/50 biphasic waveform while five patients had lower ADFT with 65/65 biphasic waveform. Equivalent reduction in ADFT was seen in the remaining six patients. The ADFT was 0.83 +/- 0.65 J when both tilts were considered. In conclusion, biphasic waveform tilt modification may affect the ADFT in an individual patient. The optimal biphasic waveform for ADFT is not known.