Effects of SO2 on selective catalytic reduction of NO with NH3 over a TiO2 photocatalyst

The effect of SO₂ gas was investigated on the activity of the photo-assisted selective catalytic reduction of nitrogen monoxide (NO) with ammonia (NH₃) over a TiO₂ photocatalyst in the presence of excess oxygen (photo-SCR). The introduction of SO₂ (300 ppm) greatly decreased the activity of the photo-SCR at 373 K. The increment of the reaction temperature enhanced the resistance to SO₂ gas, and at 553 K the conversion of NO was stable for at least 300 min of the reaction. X-ray diffraction, FTIR spectroscopy, thermogravimetry and differential thermal analysis, x-ray photoelectron spectroscopy (XPS), elemental analysis and N₂ adsorption measurement revealed that the ammonium sulfate species were generated after the reaction. There was a strong negative correlation between the deposition amount of the ammonium sulfate species and the specific surface area. Based on the above relationship, we concluded that the deposition of the ammonium sulfate species decreased the specific surface area by plugging the pore structure of the catalyst, and the decrease of the specific surface area resulted in the deactivation of the catalyst.     

Effect of Milling on Slip Casting of Partially Stabilized Zirconia

Specimens of partially stabilized zirconia were slip cast from aqueous suspensions and sintered at 1500°C for 3 h. The relative density of the cast specimens and the firing shrinkage of the sintered specimens depend on the milling time for the suspension. Vickers hardness and K_IC values of 11.46±s0.07 GN/m² and 6.10 ±0.04 MN.m^3/2, respectively, were obtained for all sintered specimens. The dispersion of the suspension is important in increasing the relative density of the cast specimens.     

Characterization and electrochemical properties of CF4 plasma-treated boron-doped diamond surfaces

The effect of CF₄ plasma etching on diamond surfaces, with respect to treatment time, was investigated using scanning electron microscopy (SEM), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and electrochemical measurements. SEM observations and Raman spectra indicated an increase in surface roughening on a scale of 10–20 nm, and an increase in crystal defect density was apparent with treatment time in the range of 10 s to 30 min. In contrast, alteration of the diamond surface terminations from oxygen to fluorine was found to be rather rapid, with saturation of the F/C atomic ratio estimated from XPS analysis after treatment durations of 1 min and more. The redox kinetics of Fe(CN)₆^3−/4− was also found to be significantly modified after 10 s of CF₄ plasma treatment. This behavior shows that C–F terminations predominantly affect the redox kinetics compared to the effect on the surface roughness and crystal defects. The double-layer capacitance (C_dl) of the electrolyte/CF₄ plasma-treated boron-doped diamond interface was found to show a minimum value at 1 min of treatment. These results indicate that a short-duration CF₄ plasma treatment is effective for the fabrication of fluorine-terminated diamond surfaces without undesirable surface damage.     

Growth of Potassium Titanate Fibers in Flowing N2 Gas

The length of potassium titanate fibers produced by several conventional methods averages 50 μm, with a maximum of 100 μm. Extremely long fibers (most >1000 μm long) were obtained by calcination in N₂ gas flowing at 5.2×10^-4 m/s.     

Improved direct bonding method of Nd:YVO4 and YVO4 laser crystals

We succeeded in the fabrication of bonded laser crystals composed of a neodymium-doped YVO₄ laser crystal (Nd:YVO₄) and its host crystals YVO₄ by a newly developed dry etching technique using an argon ion beam. The optical distortion caused by the bonded interface of size 5 mm × 6 mm was estimated to be 0.05λ at 633 nm. From the comparison of laser performance pumped by a laser diode, the bonded crystals could increase the laser output power by nearly twice that of the non-bonded crystals with the same degree of polarization of 99.2%. To analyze the mechanism of the enhanced reduction of the thermal load in the bonded crystals, numerical simulations with a finite-element method were also performed.     

Efficacy of interferons in treating children with chronic hepatitis C

Twenty-two children with chronic hepatitis serologically positive for hepatitis C virus (HCV) were treated with interferon-alpha (IFN-alpha). Liver biopsy showed chronic active hepatitis in 13 and chronic persistent hepatitis in 9 patients. A sustained clearance of HCV was observed in 8/22 children 12 months after the administration of IFN-alpha for 26 weeks, associated with normalization of HCV core antibody. Of these eight patients six had HCV genotype III and two HCV genotype II or IV. Hepatitis relapsed in seven other patients after completion of IFN-alpha with an increase in HCV core antibody titre, five with HCV genotype II, and two with HCV genotype III or IV. A second course of IFN-alpha suppressed the reactivation of HCV in all seven patients. Three of seven responders who relapsed after the first course remained negative for HCV RNA 12 months after their second course of IFN-alpha. However, the remaining four patients with HCV genotype II again relapsed after completing their second course of IFN-alpha. Seven children with the HCV genotype II resistant to IFN, including 8 weeks of IFN-beta administration, and showed no significant reduction in HCV core antibody titre. CONCLUSION: The genotype of HCV (III) and a reduction in the core antibody titre appear to be useful parameters for predicting the response to IFN-alpha therapy.     

High-efficiency finishing process for metal mold by large-area electron beam irradiation

A new finishing process for metal molds by large-area electron beam (EB) irradiation is proposed in this study. In the large-area EB irradiation equipment used here, an EB with high-energy density is irradiated without focusing the beam, and so the EB with a maximum diameter of 60 mm can be used for melting or evaporating metal surface instantly. Experimental results show that the surface roughness decreases from 6 μmRz to less than 1 μmRz in just a few minutes under proper machining conditions. The corrosion resistance of metal mold surface also could be greatly improved by large-area EB irradiation. Furthermore, the surface roughness of tilting surface close to 90° could be well improved. Therefore, large-area EB irradiation method has a possibility to become a high-efficiency finishing process for metal molds.     

Novel anion exchange membranes having fluorocarbon backbone: Preparation and stability

Anion exchange membranes with excellent durability were prepared by chemical modification of Nafion. The modification was achieved by transformation of the sulfonic acid group into quaternary ammonium group. Namely, Nafion membrane was first converted into an amide-type membrane. Reduction of the carbonxyl group to methylene followed by quaternarization with alkyl iodide resulted in the formation of an anion exchange membrane. The electric resistance of the resulting membranes depends on the equivalent weight of the starting membranes (4.4–6.0 Ω cm² in 0.5N NaCl). The characteristics of the membranes are the excellent stability toward chemical substances such as organic solvents, oxidizing agents, acids, etc. For example, the membranes are stable in aqueous saturated chlorine solution at 60°C for 1000 hr.