Analysis of solvent extracts of bituminous coal macerals by chromatography, 1H n.m.r. and field-desorption mass spectrometry

Analysis of the carbon disulphide extracts of nine samples of UK coal-maceral concentrates by ¹H highresolution n.m.r. spectroscopy, gas-liquid chromatography and field-desorption mass spectrometry indicates the presence of components with a wide molecular weight range extending up to 1200 amu; these are attributed to n-alkanes up to ≈C₅₀ and highly condensed polynuclear aromatic compounds.     

Cyclic alkanes as geochemical markers in coal liquefaction products

Branched-chain/cyclic alkanes have been obtained, by solvent extraction and molecular-sieve adsorption, from a UK low-temperature (Rexco) coal tar, a USA fluidized-bed pyrolysis (FMC COED) coal tar, and a novel supercritical-gas-extract of a Turkish (Elbistan) lignite. Mass spectrometry (with gas chromatography and field-desorption) established the presence of mono-, di (including sesquiterpanes), tri-, tetra- (steranes only), and pentacyclic (triterpanes only) alkanes, including several steranes and triterpanes not previously reported as coal-tar constituents. The potential of cyclic alkanes as geochemical markers, even for commercial coal products subjected to appreciable heat treatment, is demonstrated by the identification of C₁₂, C₁₃, C₁₅ and C₁₆ dicyclics (including isoprenoid alkanes), C₁₇-C₂₆ tricyclics, and C₂₇ and C₂₉ hopane-type pentacyclics (triterpanes) in FMC, and of C₁₆-C₃₈ monocyclics, C₃₄-C₃₆ dicyclics, C₂₂-C₃₆ tricyclics, C₂₇-C₃₀ tetracyclics (steranes), and C₂₇, C₂₉, C₃₀, C₃₁, C₃₂, and C₃₃ hopane-type pentacyclics (triterpanes) in Rexco tar. Tetra- and pentacyclic alkanes were also preserved in the lignite extract.     

Cross-section transmission electron microscopy of the ion implantation damage in annealed diamond

It has formerly been shown that low-damage levels, produced during the implantation doping of diamond as a semiconductor, anneal easily while high levels “graphitize” (above about 5.2 × 10¹⁵ ions/cm²). The difference in the defect types and their profiles, in the two cases, has never been directly observed. We have succeeded in using cross-section transmission electron microscopy to do so. The experiments were difficult because the specimens must be polished to ∼40 μm thickness, then implanted on edge and annealed, before final ion beam thinning to electron transparency. The low-damage micrographs reveal some deeply penetrating dislocations, whose existence had been predicted in earlier work.     

Composite Semiconductor Material of Carbon Nanotubes and Poly[5,5′-bis(3-dodecyl-2-thienyl)-2,2′-bithiophene] for High-Performance Organic Thin-Film Transistors

A nonpercolating network of non-covalently functionalized single-walled carbon nanotubes was embedded within air-stable poly[5,5′-bis(3-dodecyl-2-thienyl)-2,2′-bithiophene] (PQT-12) thin films for the purpose of enhancing the field-effect mobility in thin-film transistors. The host polymer was used to stabilize the nanotubes in suspension through π-orbital overlap caused by simple application of ultrasonication. The stable nanotube suspension was cast into two different device architectures, both of which exhibited excellent on/off ratios ranging from 10⁵ to 10⁶ and dramatically improved mobilities compared with pristine PQT-12 semiconductor. A single-layer film with nanotubes embedded throughout was easy to fabricate and had mobility up to 0.34 cm²/Vs, an enhancement of over 3× compared with PQT-12. Placing the nanotubes closer to the dielectric surface in a dual-layer approach resulted in a mobility improvement of up to six times (0.58 cm²/Vs). The effects of the nanotube content on the polymer interaction within the suspension, film morphology, and electrical properties were investigated as well.     

Epistemology and conceptual resources for the development of learning technologies

Abstract   The issues raised by the design and development of technologies to enhance learning has led to a demand for an appropriate language and form of conceptualization. However, we are insufficiently familiar with the way in which different types of mediated tool use occur, to develop the theoretical models needed for the development of this language and form of conceptualization. In its absence a somewhat eclectic variety of concepts and research, such as the concept of affordance, are recruited in accounts of learning with new technologies. In looking briefly at the relevant area in philosophy this paper will consider whether or not the use of concepts such as affordance give adequate weight to social practice, meaning and knowledge in the design of educational technology. A fruitful source for work in this field which has not been sufficiently exploited is philosophy, particularly recent work in epistemology.     

Formation of cBN nanocrystals by He+ implantation into hBN

The structural modifications of polycrystalline hexagonal boron nitride implanted with He⁺ beams at energies between 200 keV and 1.2 MeV to fluences of 1.0 × 10¹⁷ ions cm^? 2 were investigated using micro-Raman spectroscopy. The measured Raman spectra show evidence of implantation-induced structural transformations from the hexagonal phase to nanocrystalline cubic boron nitride, rhombohedral boron nitride and amorphous boron nitride phases. The first-order Longitudinal-Optical cubic boron nitride phonon was observed to be downshifted and asymmetrically broadened and this was explained using the spatial correlation model coupled with the high ion implantation-induced defect density.     

Diamond surfaces polished both mechanically and manually; an atomic force microscopy (AFM) study

Diamond surfaces that are polished both mechanically and manually have been studied using atomic force microscopy and compared with optical micrographs obtained within the Nomarski interference mode. The extra gentle manual polishing which follows the mechanical polishing was developed to produce much smoother, well characterized and flat diamond surfaces than those prepared through mechanical polishing only. Both the AFM and optical micrographs showed the manually polished diamond surfaces being smoother and also exhibiting lower roughness parameters than those polished mechanically only. Annealing the surfaces to 250 °C did not show any noticeable changes in the surface roughnesses, but a 750 °C vacuum-anneal did show some differences that were attributed to possible surface etching through the desorption of the surface-bonded species.