EXPERIMENTAL ESTIMATION OF A SCALING EXPONENT FOR TIP VORTEX CAVITATION VIA ITS INCEPTION TEST IN FULL- ANDMODEL-SHIP

Tip vortex cavitation noise of marine propeller became primary concerns to reduce hazardous environmental impacts from commercial ship or to keep the underwater surveillance of naval ships. The investigations of the tip vortex and its induced noise are normally conducted through the model test in a water cavitation tunnel. However the Reynolds number of model-test is much smaller than that of the full-scale, which subsequently results in the difference of tip vortex cavitation inception. Hence, the scaling law between model-and full-scales needs to be identified prior to the prediction and assessment of propeller noise in full scale. From previous researches, it is generally known that the incipient caivtation number of tip vortex can be represented as a power of the Reynolds number. However, the power exponent for scaling, which is the main focus of this research, has not been clearly studied yet. This paper deals with the estimation of scaling exponent based on tip vortex cavitation inception test in both full-and model-scale ships. Acoustical measurements as well as several kind of signal processing technique for an inception criterion suggest the scaling exponent as 0.30. The scaling value proposed in this study shows slight difference to the one of most recent research. Besides, extrapolation of model-ship noise measurement using the proposed one predicts the full-scale noise measurement with an acceptable discrepancy.     

Numerical Analysis of Coaxial Double Gate Schottky Barrier Carbon Nanotube Field Effect Transistors

Carbon nanotube field-effect transistors (CNTFETs) have been studied in recent years as a potential alternative to CMOS devices, because of the capability of ballistic transport. The ambipolar behavior of Schottky barrier CNTFETs limits the performance of these devices. A double gate design is proposed to suppress this behavior. In this structure the first gate located near the source contact controls carrier injection and the second gate located near the drain contact suppresses parasitic carrier injection. To avoid the ambipolar behavior it is necessary that the voltage of the second gate is higher or at least equal to the drain voltage. The behavior of these devices has been studied by solving the coupled Schrödinger-Poisson equation system. We investigated the effect of the second gate voltage on the performance of the device and finally the advantages and disadvantages of these options are discussed.     

Shop-floor scheduling at shipbuilding yards using the multiple intelligent agent system

The intelligent agent system has become a typical approach to research distributed artificial intelligence and distributed problem solving. However, despite its various technical advantages, the distribution and expansion of the intelligent agent system approach has been limited because existing methodologies rely on specialized applications and therefore require intensive investment to develop new systems. In an attempt to conquer these difficulties, a standardized methodology to construct intelligent agent systems is proposed. This approach deviates from current agent system approaches of repeatedly constructing new and customized expert systems. Specifically, it provides an economical method for developing intelligent agent systems by investigating the possibility of standardizing message communication protocols in linguistics speech-act theory and by supplementing traditional algorithmic systems with intelligent segments using, among others, expert system tools. To verify effectiveness, the shop-floor scheduling system of a large-scale shipbuilding yard has been redesigned, developed, and tested using this approach. This shop-floor scheduling system requires the scheduling of when and where to process block construction under various constraints. It is a difficult four-dimensional time and space allocation problem involving traditional NP-complete search spaces. The tested intelligent agent system proposes an innovative method for reducing the search space into three levels: the algorithm level, the agent intelligence level, and the level of cooperation among agents. It also provides methods for solving deadlock occurrence and non-uniformity problems resulting from parallel processing. Test results demonstrate applicability and economy, among other technical advantages.     

A Modification of the Coates Gain Formula for the Analysis of Linear Systems

In this paper, the Coates flow-graph gain formula is modified by the introduction of the loop-set and the two-loop-set, baaed on the concepts of the tree and the two-tree in network topology. The analogy is evident by observing that the two-trees T _ij of a given graph G can be obtained by coalescing vertices i and j of G and thon removing the self-loops. In a similar manner, the two-loop-sets can be obtained from the flow graph by first modifying the graph and then obtaining the loop-sets of tho modified graph. Because of such modification, the derivation of tho gain formula is considerably simplified. Consequently, the evaluation of the terms in the formula becomes easier. Finally, a simple method of determining the number of terms in the formula is derived as a check against possible omission of terms due to carelessness.     

Optimal control of economic growth with application to Korean economy

This paper is concerned with the application of optimal control theory to the dual growth of the Korean economy. A closed two sector economic growth model is formulated by dividing the economy into agriculture and non-agriculture in order to represent the transitional phenomena between the two sectors. Taking capital and saving as state and control variables, respectively, the model governing the economic growth becomes a non-linear simultaneous differential equations with coupling terms of state and control variables. Assuming the Cobb-Douglas production function and the exponential form of the social welfare function, the necessary and sufficient conditions of the optimal control have been derived for the case of finite planning horizon by using the Pontryagin's maximum principle. Since deriving the optimal trajectories of state and control variables analytically is impossible, a numerical procedure based on the variation of extremals is used to obtain the optimal paths of the aggregate investment and consumption of the Korean economy.     

Effect of pulse time on surface characteristics and corrosion resistance during pulse electrochemical polishing

Pulse electrochemical polishing (PECP) was used to improve the mechanical properties,such as surface roughness and corrosion resistance,of conductive metallic materials.PECP can provide a smooth,bright,reflective,and deburred surface that exhibits superior corrosion resistance.In this work,stainless steel was used as the anode,and copper was used as the cathode due to their low electrical resistances.The surface roughness of the PECP sample was measured by atomic force microscopy (AFM).A scanning electron microscope (SEM) was used to observe surface characteristics,and an Auger electron spectroscope (AES) was used to analyze the metallurgical composition and thickness of the passive film.The aim of this research was to compare the corrosion resistance rates of the unprocessed and PECP-processed stainless steel.     

Optimal number of minor failures before replacement

This paper extends a replacement model based on failure number to include a repair-cost limit for general failure distributions. The stochastic behaviour of failures and repair costs are modelled by a non-homogeneous Poisson process. An efficient marginal analysis algorithm is presented for finding the optimal failure number for replacement that minimizes the average cost rate.     

Evaluation of microstructure and mechanical properties of Mg-xCe-0.5Zn alloys by nano-indentation

The microstructure and mechanical properties of Mg-xCe-0.5Zn(x=0.5,1.5,2.5,molar fraction,%) alloys were examined using a nano-indentation technique.The alloys were fabricated using a vacuum induction melting method under an argon atmosphere. The microstructures of Mg-xCe-0.5Zn alloys mainly consist ofα-Mg and eutectic Mg12Ce phase.The volume fraction and size of the eutectic Mg12Ce phase increase with increasing Ce contents.Nano-indentation test results show that the indentation hardness and elastic modulus of the eutectic Mg12Ce phase are higher than those of theα-Mg matrix.In addition,the mean indentation hardness and elastic modulus of the Mg-xCe-0.5Zn alloys increase with the Ce addition amount increasing.