Model Validation for Bridge-Road-Vehicle Dynamic Interaction System

The dynamic response of highway bridges subjected to moving truckloads has been observed to be dependent on (1) dynamic characteristics of the bridge; (2) truck configuration, speed, and lane position on the bridge; and (3) road surface roughness profile of the bridge and its approach. Historically, truckloads were measured to determine the load spectra for girder bridges. However, truckload measurements are either made for a short period of time [for example, weigh-in-motion (WIM) data] or are statistically biased (for example, weigh stations) and cost prohibitive. The objective of this paper is to present results of a 3D computer-based model for the simulation of multiple trucks on girder bridges. The model is based on the grillage approach and is applied to four steel girder bridges tested under normal truck traffic. Actual truckload data collected using a discrete bridge WIM system are used in the model. The data include axle loads, truck gross weight, axle configuration, and statistical data on multiple presence (side by side or following). The results are presented as a function of the static and dynamic stresses in each girder and compared with code provisions for dynamic load factor. The study provides an alternate method for the development of live-load models for bridge design and evaluation.     

Evaluation of Laminated Circular Elastomeric Bearings

This paper evaluates the behavior and performance of laminated circular elastomeric bearings and compares them to those of square and rectangular bearings. The study included an experimental evaluation and a nationwide survey of state Department of Transportations on the use and performance of circular bearings and bearings in general in their states. The experimental investigation studied the bearings' behavior in compression, compression and rotation, and compression and shear. Results from this limited study showed that the three bearings have similar stress-strain behavior in compression and they are in agreement with the AASHTO LRFD guide stress–strain curves. In compression and rotation, the AASHTO LRFD substructure moments are slightly less than the measured values for circular bearings and rectangular bearings rotated about their strong axis for a compressive stress of 10.3?MPa (1.5?ksi) and slightly higher than those of rectangular bearings rotated about their weak axis. In compression and shear, the shear stiffness of circular and square bearings is in agreement with theoretical values within the range of design displacements. Results from the survey showed that many states are using circular bearings and more states would consider using them, however no maintenance or monitoring data were available on their short-term and long-term performance.     

Effects of a single dose of N-Acetyl-5-methoxytryptamine (Melatonin) and resistance exercise on the growth hormone/IGF-1 axis in young males and females

Melatonin and resistance exercise alone have been shown to increase the levels of growth hormone (GH). The purpose of this study was to determine the effects of ingestion of a single dose of melatonin and heavy resistance exercise on serum GH, somatostatin (SST), and other hormones of the GH/insulin-like growth factor 1 (IGF-1) axis. Physically active males (n = 30) and females (n = 30) were randomly assigned to ingest either a melatonin supplement at 0.5 mg or 5.0 mg, or 1.0 mg of dextrose placebo. After a baseline blood sample, participants ingested the supplement and underwent blood sampling every 15 min for 60 min, at which point they underwent a single bout of resistance exercise with the leg press for 7 sets of 7 reps at 85% 1-RM. After exercise, participants provided additional blood samples every 15 min for a total of 120 min. Serum free GH, SST, IGF-1, IGFBP-1, and IGFBP-3 were determined with ELISA. Data were evaluated as the peak pre- and post-exercise values subtracted from baseline and the delta values analyzed with separate three-way ANOVA (p < 0.05). In males, when compared to placebo, 5.0 mg melatonin caused GH to increase (p = 0.017) and SST to decrease prior to exercise (p = 0.031), whereas both 0.5 and 5.0 mg melatonin were greater than placebo after exercise (p = 0.045) and less than placebo for SST. No significant differences occurred for IGF-1; however, males were shown to have higher levels of IGFBP-1 independent of supplementation (p = 0.004). The 5.0 mg melatonin dose resulted in higher IGFBP-3 in males (p = 0.017). In conclusion, for males 5.0 mg melatonin appears to increase serum GH while concomitantly lowering SST levels; however, when combined with resistance exercise both melatonin doses positively impacts GH levels in a manner not entirely dependent on SST.     

Obesity: Prevalence,Theories, Medical Consequences,Management, and Research Directions

Obesity and its associated disorders are a growing epidemic across the world. Many genetic, physiological, and behavioral factors play a role in the etiology of obesity. Diet and exercise are known to play a valuable role in the treatment and prevention of obesity and associated disorders such as hypertension, heart disease, and diabetes. Therefore, the purpose of this review is to examine the prevalence, etiology, consequences, and treatment of obesity.     

Fundamental foaming mechanisms governing the volume expansion of extruded polypropylene foams

This article describes the fundamental foaming mechanisms that governed the volume expansion behavior of extruded polypropylene (PP) foams. A careful analysis of extended experimental results indicated that the final volume expansion ratio of the extruded PP foams blown with butane was governed by either the loss of the blowing agent or the crystallization of the polymer matrix. A charge coupling device (CCD) camera was installed at the die exit to carefully monitor the shape of the extruded PP foams. The CCD images were analyzed to illustrate both mechanisms, gas loss and crystallization, during foaming at various temperatures, and the maximum expansion ratio was achieved when the governing mechanism was changed from one to the other. In general, the gas loss mode was dominant at high temperatures and the crystallization mode was dominant at low temperatures. When the gas loss mode was dominant, the volume expansion ratio increased with decreasing temperature because of the reduced amount of gas lost. By contrast, when the crystallization mode was dominant, the expansion ratio increased with increasing temperature because of the delayed solidification of the polymer. The processing window variation with the butane concentration, the change in the temperature ranges for the two governing modes, and the sensitivity of melt temperature variations to the volume expansion ratio are discussed in detail on the basis of the obtained experimental results for both branched and linear PP materials. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2661–2668, 2004     

Progress and challenges in sustainability,compatibility, and production of eco-composites: A state-of-art review

Owing to economic and environmental benefits, new generations of materials/commodities follow “from waste to wealth” strategy. Recently, there has been a huge upsurge in research on the development of eco-composites using recycled plastic polymers and agro-residues because the eco-composites satisfy the stringent environment regulations and are cost-effective. Herein, we present a detailed review on the potential use of several types of natural fillers as an efficient reinforcement for recycled plastic polymers. In particular, the characterization of different categories of eco-composites according to their morphological, physical, thermal, and mechanical properties is extensively reviewed and their results are analyzed, compared, and highlighted. Furthermore, a framework to produce functional eco-composites, which includes functionalization of ingredients, critical issues on microstructural parameters, processing, and fabrication methods, is outlined and supported with sufficient data from the literature. Finally, the review outlines the emerging challenges and future prospects of eco-composites to be addressed by interested researchers to bridge the gap between research and commercialization of such a class of material. Overall, the acquired knowledge will guide researchers, scientists, and manufacturers to plan, select, and develop various forms of eco-composites with enhanced properties and optimized production processes.     

Structural study of titanium oxide films synthesized by ion beam-assisted deposition

The application of titanium dioxide (TiO(2)) films as surgical implant coatings for antibiotic attachment depends crucially on their available surface area and thus their surface morphology and crystallinity. Here, we report our fabrication of high Wenzel ratio TiO(2) films targeted to increase the film surface area using the ion beam-assisted deposition (IBAD) technique at high-deposition temperatures (approximately 610 degrees C). The modulation of the films' surface morphology was accomplished by varying the chemical identity of the concurrent ion beams bombarded on the films during the e-beam evaporation process. Atomic force microscopy (AFM) and scanning electron microscopy (SEM) were employed to investigate the surface morphology of the as-deposited films. X-ray diffractometry (XRD) revealed that these nanocrystalline films primarily consist of anatase phase TiO(2). Wenzel ratio, the ratio of the actual surface area to the projected area, of IBAD films prepared with argon, oxygen, and nitrogen ion beams was measured to be 1.52, 1.31 and 1.49, respectively. The effect of the differences in chemical reactivity and ion size of these three type ion beams are discussed to explain the present results.     

Investigating the influence of the counter Si-cell on the optoelectronic performance of high-efficiency monolithically perovskites/silicon tandem cells under various optical sources

Nowadays, tandem structures have become a valuable competitor to conventional silicon solar cells, especially for perovskite over silicon, as metal halides surpassed Si with tunable bandgaps, high absorption coefficient, low deposition, and preparation costs. This led to a remarkable enhancement in the overall efficiency of the whole cell and its characteristics. Consequently, this expands the usage of photovoltaic technology in various fields of applications not only under conventional light source spectrum in outdoor areas, i.e., AM1.5G, but also under artificial light sources found indoors with broadband intensity values, such as Internet of things (IoTs) applications to name a few. We introduce a numerical model to analyze perovskite/Si tandem cells (PSSTCs) using both crystalline silicon (c-Si) and hydrogenated amorphous silicon (a-Si:H) experimentally validated as base cells. All proposed layers have been studied with J-V characteristics and energy band diagrams under AM1.5G by using SCAPS-1D software version 3.7.7. Thereupon, the proposed architectures were tested under various artificial lighting spectra. The proposed structures of Li4Ti5O12/CsPbCl3/MAPbBr3/CH3NH3PbI3/Si recorded a maximum power conversion efficiency (PCE) of 25.25% for c-Si and 17.02% for a-Si:H, with nearly 7% enhancement concerning the Si bare cell in both cases.