Electrical Breakdown Properties and Space Charge Formation in High Temperature Region in Ultraviolet Ray Irradiated PVC

Polyvinyl chloride (PVC) is the most popular insulating material for electric wiring instruments. However, an exothermic reaction above 150 °C may cause deterioration of the insulating properties of PVC. Therefore, it is important to clarify the heat degradation in PVC, not only to investigate the ignition of electrical wiring products but also to use electrical products safely. It is known that ultraviolet (UV) irradiation causes chemical deterioration of PVC and an increase in its conductivity. Generally, it has been thought that the electrical breakdown properties, electrical conduction, and insulating performance are affected by space charge accumulation in an insulating material. A high temperature pulsed electroacoustic (PEA) system usable up to 250 °C has been developed, and the PEA system can measure the space charge distribution and conduction current in the high temperature range simultaneously. In this investigation, the space charge distribution and conduction current were measured up to electrical breakdown in a non‐UV irradiated sample (normal PVC) and in 353 nm and 253 nm UV‐irradiated PVC samples in the range from room temperature to 200 °C in a DC electric field. In the short wavelength UV irradiated PVC sample (253 nm, 300 h), a deterioration of breakdown strength at 90 °C to 150 °C and negative packet‐like charges were observed at 60 °C and 100 °C, a positive charge accumulated in front of both the anode and cathode above 90 °C, and a higher electric field near the cathode side because the positive charge of the cathode side was greater.     

Fabrication of lotus-type porous carbon steel by the continuous zone melting method and its mechanical properties

A lotus-type porous carbon steel with cylindrical pores was fabricated by the continuous zone melting method in a pressurized mixture of hydrogen and helium gases. The porosity increases with increasing partial pressure of the hydrogen gas, while the pore diameter remains almost constant, independent of the pressure. The ultimate tensile strength of the specimen with cylindrical pores parallel to the tensile direction is lower than the estimated value, assuming that the strength is decreased in proportion to the decrease of the cross-sectional area of the specimen, while the yield strength is higher than the estimated value. The compressive yield strength is also higher than the estimated value. The increase in yield strength is considered to be due to precipitation strengthening. The tensile strength is increased by quenching and tempering, while the elongation decreases. Such mechanical properties are discussed in terms of the microstructural analysis.     

Design for Consecutive Testability of System-on-a-Chip with Built-In Self Testable Cores

This paper introduces a new concept of testability called consecutive testability and proposes a design-for-testability method for making a given SoC consecutively testable based on integer linear programming problem. For a consecutively testable SoC, testing can be performed as follows. Test patterns of a core are propagated to the core inputs from test pattern sources (implemented either off-chip or on-chip) consecutively at the speed of system clock. Similarly the test responses are propagated to test response sinks (implemented either off-chip or on-chip) from the core outputs consecutively at the speed of system clock. The propagation of test patterns and responses is achieved by using interconnects and consecutive transparency properties of surrounding cores. All interconnects can be tested in a similar fashion. Therefore, it is possible to test not only logic faults but also timing faults that require consecutive application of test patterns at the speed of system clock since the consecutively testable SoC can achieve consecutive application of any test sequence at the speed of system clock.     

Preparation and antibacterial activity of novel fluoroalkyl end-capped oligomers/silica nanocomposites-encapsulated low molecular biocides

Fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide oligomer [R_F-(DOBAA) _n -R_F] reacted with tetraethoxysilane (TEOS) and silica nanoparticles in the presence of low-molecular weight biocides such as hibitane, hinokitiol, and hinokioil under alkaline conditions to afford R_F-(DOBAA) _n -R_F/silica nanocomposites-encapsulated these biocides in excellent to moderate isolated yields. Fluoroalkyl end-capped N,N-dimethylacrylamide oligomer [R_F-(DMAA) _n -R_F] and acrylic acid oligomer [R_F-(ACA) _n -R_F]/silica nanocomposites-encapsulated hibitane were obtained under similar conditions. Dynamic light scattering measurements showed that the size of these fluorinated nanocomposites-encapsulated biocides thus obtained is nanometer size-controlled. Additionally, these fluorinated nanocomposites were shown to have a good dispersibility and stability in methanol and water. Of particular interest, these fluorinated nanocomposites-encapsulated biocides were found to have a good antibacterial activity against Staphylococcus aureus, and these nanocomposites were applied to the surface modification of traditional organic polymers such as poly(methyl methacrylate).     

Crack opening displacement of a through-wall crack in a plate subjected to bending load

This study was performed in order to clarify crack opening displacement (COD) of through-wall cracks in a plate subjected to bending load. The former COD evaluation methods were mainly developed corresponding to tensile load, but there has been nothing that has been developed corresponding to bending load. Therefore, the authors evaluated CODs of the through-wall cracks in plates which were subjected to a bending load using finite element method (FEM) analyses, and proposed a simplified COD evaluation method accounting for both tensile and bending loads. The proposed method is useful for leakage evaluation at a crack opening of an elbow crown or in the vicinity of the coolant surface of a vessel in which the bending stress is relatively large.     

Interleukin-6 cDNA transfected Lewis lung carcinoma cells show unaltered net tumour growth rate but cause weight loss and shortened survival in syngeneic mice

HuIL-6 cDNA, cloned into a neomycin resistant conferring expression vector, BMGNeo, was transfected into Lewis Lung Carcinoma (LLC) cells. LLC cells (5 x 10(6) ml-1) transfected with IL-6 cDNA (LLC-IL6) secreted IL-6 into the culture supernatant at a concentration of 9.9 ng ml-1 within 48 h. When 1,000,000 of untransfected LLC, BMGNeo vector transfected LLC (LLC-Neo) or LLC-IL6 cells were transplanted into C57BL/6 mice subcutaneously, the mean +/- s.d. of survival times of these mice were 33.3 +/- 9.7, 34.3 +/- 7.1 and 17.0 +/- 3.1 days, respectively. The survival time of LLC-IL6 cells transplanted mice was significantly shorter than that of LLC (P < 0.01) or LLC-Neo (P < 0.01) cells transplanted mice without a measurable difference of tumour size. Plasma concentration of IL-6 steadily increased in LLC-IL6 transplanted mice. Body weight and serum albumin were significantly lower in LLC-IL6 transplanted mice than in LLC transplanted mice. Mouse IL-1 alpha and mouse TNF-alpha were not detected in the plasma of LLC-IL6 transplanted mice. These data suggested that secretion of IL-6 from LLC cells was unable to alter net tumour growth rate but rather caused a state similar to cachexia without detectable increase of IL-1 alpha and TNF-alpha in the plasma. This state may be responsible for the shortened survival of LLC-IL6 tumour-bearing mice.     

Hot carrier magnetophonon spectroscopy of semiconductors in high magnetic fields up to 40 T

Hot carrier magnetophonon resonances of n-type Si, short channel InP and p-type InSb were investigated in pulsed high magnetic fields up to 40 T. Using a recently developed high resolution technique in pulsed high fields, many new features of the hot carrier-phonon interactions in high magnetic fields were found.     

Survey of switching techniques in high-speed networks and their performance

One of the most promising approaches for high speed networks for integrated service applications is fast packet switching, or ATM (asynchronous transfer mode). ATM can be characterized by very high speed transmission links and simple, hard-wired protocols within a network. To match the transmission speed of the network links, and to minimize the overhead due to the processing of network protocols, the switching of cells is done in hardware switching fabrics in ATM networks. A number of designs have been proposed for implementing ATM switches. Although many differences exist among the proposals, the vast majority of them are based on self-routeing multistage interconnection networks. This is because of the desirable features of multi-stage interconnection networks such as self-routeing capability and suitability for VLSI implementation. Existing ATM switch architectures can be classified into two major classes: blocking switches, where blockings of cells may occur within a switch when more than one cell contends for the same internal link, and non-blocking switches, where no internal blocking occurs. A large number of techniques have also been proposed to improve the performance of blocking and non-blocking switches. In this paper, we present an extensive survey of the existing proposals for ATM switch architectures, focusing on their performance issues.