Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

Reduction of loading effect by tungsten etchback in a magneticallyenhanced reactive ion etcher

The plug loading effect occurring during the etchback of tungsten was investigated in a magnetically enhanced reactive ion etcher using SF ₆/Ar mixtures. It was found that while the plug loading effect is independent of varying SF₆/Ar flow rate ratio and magnetic field intensity, it is reduced under the condition of high selectivity of tungsten relative to TiN which was achieved at high chamber pressure and low RF power. It is proposed that when TiN is used as a glue layer, the W etch rate enhancement in the plug is mainly controlled by a local loading effect. Under the optimized etchback conditions the plug loss was successfully controlled without the tungsten residue left on severe topology     

Antioxidant activity of anacardic acids

Anacardic acids, 6-pentadec(en)ylsalicylic acids isolated from the cashew Anacardium occidentale L. (Anacardiaceae) nut and apple, were found to possess preventive antioxidant activity while salicylic acid did not show this activity. These anacardic acids prevent generation of superoxide radicals by inhibiting xanthine oxidase (EC 1.1.3.22, Grade IV) without radical-scavenging activity. Notably, the inhibition kinetics of anacardic acids do not follow hyperbolic dependence of enzyme inhibition on inhibitor contents (Michaelis–Menten equation) but follow the Hill equation instead. Anacardic acid (C_15:1) inhibited the soybean lipoxygenase-1 (EC 1.13.11.12, Type 1) catalyzed oxidation of linoleic acid with an IC₅₀ of 6.8 μM. The inhibition is a slow and reversible reaction without residual enzyme activity. The inhibition kinetics indicate that anacardic acid (C_15:1) is a competitive inhibitor and the inhibition constant, K_I, was 2.8 μM. Anacardic acids act as antioxidants in a variety ways, including inhibition of various prooxidant enzymes involved in the production of the reactive oxygen species and chelate divalent metal ions such as Fe²⁺ or Cu²⁺, but do not quench reactive oxygen species. The C₁₅-alkenyl side chain is largely associated with the activity.     

Extrinsic calibration of a camera and laser range finder using a new calibration structure of a plane with a triangular hole

Sensor fusion of a camera and laser range finder is important for the autonomous navigation of mobile robots. Finding the transformation between the camera and laser range finder is the first necessary step for the fusion of information. Many algorithms have been proposed, but these tend to require many different steps in order to achieve reliable and accurate results. A calibration structure that has triangular hole on its plane is proposed for the extrinsic calibration of a camera and laser range finder. Locations of laser scan data that are invisible on the calibration plane can be determined using property on the proposed calibration structure. First, we classify the laser scan data into two groups where one is on the plane and the other is off the plane. Then, we determine the absolute location of the laser scan data on the plane through a search of the parameters of the line. Finally, we can establish 3D-3D correspondences between the camera and laser range finder. Extrinsic calibration between a camera and laser range finder is found using a conventional 3D-3D transformation computing algorithm. Keywords: Calibration k]camera k]extrinsic calibration k]laser range finder     

Operation, system architectures, and physical Layer design considerations of distributed MAC protocols for UWB

Impulse-based ultra wideband (I-UWB) is an attractive radio technology for large ad hoc and sensor networks due to its robustness to harmful multipath effects, sub-centimeter ranging ability, simple hardware, and low radiated power. To scale to large sizes, networks often implement distributed medium access control (MAC) protocols. However, most MAC protocols for I-UWB are centralized, and they target small wireless personal area networks and cellular networks. We propose three distributed MAC protocols suitable for I-UWB. Two multichannel protocols, called multichannel pulse sense multiple access (M-PSMA) and multichannel ALOHA achieve high aggregate throughput. A busy-signal protocol, called busy-signal multiple access (BSMA), reduces the energy wasted from re-transmitted packets. This paper describes the three protocols in terms of the protocol's operation, the supporting system architecture, and the I-UWB physical layer. Physical layer simulations confirm the feasibility of implementing the proposed systems and also provide parameters for network simulations. Network simulations show that the throughput of M-PSMA exceeds that of a centralized time-division multiple-access protocol and that the energy efficiency of BSMA far surpasses that of other distributed protocols.     

Preparation of AZ91D Slurries for Semi-Solid Forming Using Al8 ( Mn, Fe) 5 Precipitates

During the solidification of the AZ91D-alloys, the Al8(Mn, Fe)5 phase is generally precipitated in the melt in advance of the precipitation of the primary α-Mg. The basic principle for manufacturing AZ91D-alloy slurries for semi solid forming is to use the Al8(Mn, Fe)5 precipitates as the heterogeneous nucleation sites for primary α-Mg phases. Microscopic analysis for the location of the Al8(Mn, Fe)5 precipitate explains that the Al8(Mn, Fe)5 precipitate is the effective heterogeneous nucleation site for the primary α-Mg phase. It was also observed that increase of the Mn content in the melt and the cooling rate below to the solid/liquid two-phase region resulted in smaller and more globular primary α-Mg due to the increase of heterogeneous nucleation sites. It was found that the average α-Mg diameter grew as a function of t0.278, where t is the holding time at the solid/liquid two-phase region. This would be attributed to the Ostwald type ripening and coalescence between primary α-Mg phases. The cooling rate below to the solid/liquid two-phase region, Mn content in AZ91D alloy, and the holding time and temperature affected on the quality of slurry.     

Design of the dummy coil for magnet power supply

It is necessary to test it on a dummy coil, before using a magnet power supply (MPS) to energize a Poloidal Field (PF) coil in the Korea Superconducting Tokamak Advanced Research (KSTAR) device. The dummy coil should accept the same large current from the MPS as the PF coil and be within the capability of the utilities located at the KSTAR site. Therefore a coil design based on the characteristics of the MPS and other restrictive conditions needed to be made. There are three requirements to be met in the design: an electrical requirement, a structural requirement, and a water cooling requirement. The electrical requirement was that the coil should have an inductance of 40 mH. For the structural requirement, the material should be non magnetic. The coil support structure and water cooling manifold were made of SUS 304. The water cooling requirement was that there should be sufficient flow rate so that the temperature rise ΔT should not exceed 12 °C for operation at 12.5 kA for 5 min. Square cross-section hollow conductor with dimensions of 38.1 mm × 38.1 mm was used with a 25.4 mm center hole for cooling water. However, as a result of tests, it was found that the electrical and structural requirements were satisfied but that the water cooling was over designed. It is imperative that the verification will be redone for a test with 12.5 kA for 5 min.     

Chemical Processing of Nanostructured Cemented Carbide

Chemical processing is becoming a vital component in the economic development of advanced engineering materials. Our research group on chemical processing has been focussed on the development of process to produce nanophase cemented carbide. It is a much more direct route for making WC/Co than traditional processing methods, and offers the potential for lower cost production of novel materials with homogeneous nanophase microstructures and improved properties. This paper addresses the scientific and technical issues relating to the chemical processing of nanophase WC/Co composite powder and their sintering.     

A Fully-Human Antibody Specifically Targeting a Membrane-Bound Fragment of CADM1 Potentiates the T Cell-Mediated Death of Human Small-Cell Lung Cancer Cells

Small-cell lung cancer (SCLC) is the most aggressive form of lung cancer and the leading cause of global cancer-related mortality. Despite the earlier identification of membrane-proximal cleavage of cell adhesion molecule 1 (CADM1) in cancers, the role of the membrane-bound fragment of CAMD1 (MF-CADM1) is yet to be clearly identified. In this study, we first isolated MF-CADM1-specific fully human single-chain variable fragments (scFvs) from the human synthetic scFv antibody library using the phage display technology. Following the selected scFv conversion to human immunoglobulin G1 (IgG1) scFv-Fc antibodies (K103.1–4), multiple characterization studies, including antibody cross-species reactivity, purity, production yield, and binding affinity, were verified. Finally, via intensive in vitro efficacy and toxicity evaluation studies, we identified K103.3 as a lead antibody that potently promotes the death of human SCLC cell lines, including NCI-H69, NCI-H146, and NCI-H187, by activated Jurkat T cells without severe endothelial toxicity. Taken together, these findings suggest that antibody-based targeting of MF-CADM1 may be an effective strategy to potentiate T cell-mediated SCLC death, and MF-CADM1 may be a novel potential therapeutic target in SCLC for antibody therapy.