Effect of 100 KeV Ar+ ion beam irradiation on ZnO thin films – Influence of morphology vis-a-vis electrode/electrolyte interface and its impact on photoelectrochemical water splitting

The present study attempts quantitative determination of changes in the morphological surface features viz. fractal dimension, lower and upper cut off length scale through Power Spectral Density analysis prior to and after irradiation of 100 KeV Ar⁺ ion beam at incidence angles of 0°, 40° and 60° on ZnO thin films. All the unirradiated and irradiated samples are subjected to photoelectrochemical characterization and a correlation between photoelectrochemical performance and morphological parameters is established. Sample irradiated at 40° angle at the fluence of 5 × 10¹⁶ ions/cm² is found to possess maximum fractal dimension of 2.72, lower and upper cut off length scale of 3.16 nm and 63.00 nm respectively. This sample exhibits maximum photocurrent density of 3.19 mA/cm² and applied bias photon-to-current efficiency of 1.12% at 1.23 V/RHE. Hydrogen gas collected for duration of 1 h for the same sample was ~4.83 mLcm^?2.     

Masking the Peroxidase-Like Activity of the Molybdenum Disulfide Nanozyme Enables Label-Free Lipase Detection

Two-dimensional MoS₂ nanoparticles (2D-nps) exhibit artificial enzyme properties that can be regulated at bio-nanointerfaces. We discovered that protein lipase is able to tune the peroxidase-like activity of MoS₂ 2D-nps, offering low-nanomolar, label-free detection and identification in samples with unknown identity. The inhibition of the peroxidase-like activity of the MoS₂ 2D-nps was demonstrated to be concentration dependent, and as low as 5 nm lipase was detected with this approach. The results were compared with those obtained with several other proteins that did not display any significant interference with the nanozyme behavior of the MoS₂ 2D-nps. This unique response of lipase was characterized and exploited for the successful identification of lipase in six unknown samples by using qualitative visual inspection and a quantitative statistical analysis method. The developed methodology in this approach is noteworthy for many aspects; MoS₂ 2D-nps are neither labeled with a signaling moiety nor modified with any ligands for signal readout. Only the intrinsic nanozyme activity of the MoS₂ 2D-nps is exploited for this detection approach. No analytical equipment is necessary for the visual detection of lipase. The synthesis of the water-soluble MoS₂ 2D-nps is low costing and can be performed in bulk scale. Exploring the properties of 2D-nps and their interactions with biological materials reveals highly interesting yet instrumental features that offer the development of novel bioanalytical approaches.     

A prospective study of closure techniques of abdominal incisions in infants and children

In a prospective study of layered versus mass closure of abdominal incisions in infants and children, 34 cases underwent wound closure by layered and mass closure technique on an alternate basis. All the patients were assessed for their nutritional status and haemoglobin level pre-operatively, and wound complications were compared with respect to closure technique, nutritional status and normal haemoglobin level. Presence of protein energy malnutrition and anaemia did not increase the risk of wound complications with either of the technique.     

Corrosion characteristics of aluminium alloy graphite particulate composite in various environments

The present study was aimed at understanding the response of 2014 Al alloy dispersed with graphite particles in various corrosive environments. Marine (sodium chloride) as well as acidic media were selected for the purpose with a view to widen the range of utility of the composite for applications where such environments may be encountered. Studies were also extended to characterize the corrosion resistance of the composite in fresh as well as used lubricating oils to explore the possibilities of using it in bearing, bushing and such other applications. The corrosion behaviour of the base alloy processed under identical conditions was also examined in the above media to see the influence of graphite addition in the alloy. In order to assess the role of the matrix microstructure, the composite as well as the base alloy was subjected to corrosion in heat-treated as well as-cast conditions. It was observed that the specimens suffered from the maximum rate of corrosion in acid, while sodium chloride produced the minimum corrosion rate. Oil in both used and fresh conditions revealed a negligibly small extent of corrosion. The composite was found to show a higher rate of corrosion than the base alloy under identical test conditions. This was attributed to the dispersoid/matrix interfacial corrosion in the case of the graphitic aluminium alloy. Heat treatment of the composite and the base alloy was found to lower the rate of corrosion in the environments tested. Microstructural modifications of the matrix and possible relief of residual stresses were thought to be responsible for the lower rate of corrosion in the heat-treated condition.     

Analysis of a soliton-based logic module for a ring network

We analyze and numerically study the code-matching logic module that is the central element in a proposed soliton-based ring network system running at peak rates of 100 Gb/s. The proposed network is packet-switched, and fast logic is required to route each packet. That is the function of the code-matching logic module, and four soliton logic gates that can perform fast logic are the key devices in its design. The behavior of the code-matching logic module is governed by a large set of parameters, and we simulate it by varying many of these parameters. The physical effects that occur in these devices and their significance are analyzed. The results indicate that the logic module will work but within a restricted parameter range     

Structural and electrical measurements of CdZnSe composite

TheI—Vcharacterization and the electrical resistivity of selenium rich Se₈₅Cd_15-xZn_x (x = 0, 3, 7, 11 and 15) system at room temperature have been studied. Samples were obtained using melt cooling technique. So prepared samples were then characterized in terms of their crystal structure and lattice parameter using X-ray diffraction method. The materials were found to be poly crystalline in nature, having zinc blend structure over the whole range of zinc concentration. The measurements ofI—V bdcharacteristics have been carried out at different temperatures from room to 140°C. The electrical resistivity of the samples with composition at room temperature has been found to vary between maximum 2.7 x 10⁸ Ωm and minimum 7.3 x 10⁵ Ωm and shows a maximum at 3 at. wt.% of Zn. The carrier activation energy of the samples with composition has also been determined and found to vary from 0.026 eV to 0.111 eV.