Thermotropic liquid crystalline polymer (Rodrun LC5000)/polypropylene in situ composite films: rheology, morphology, molecular orientation and tensile properties

In situ composite films were prepared by a two-step method. First, polypropylene and thermotropic liquid crystalline polymer (TLCP), Rodrun LC5000 (80 mol% p-hydroxy benzoic acid (HBA)/20 mol% polyethylene terephthalate (PET)), were melt blended in a twin-screw extruder and then fabricated by extrusion through a mini-extruder as cast film. Rheological behavior of the blends, morphology of the extruded strands and films, and tensile properties of the in situ composite films were investigated. Rheological behavior of the blends at 295 °C studied using a plate-and-plate rheometer revealed a substantial reduction of the complex viscosity with increasing TLCP content, and all specimens exhibited shear thinning behavior. Over the angular frequency range of 0.6-200 rad/s, the viscosity ratio (dispersed phase to matrix phase) was found to be very low, in the range of 0.03-0.07. Morphologies of the fracture surfaces of the blend extrudates and the film surfaces etched in permanganic solution were investigated by scanning electron microscope (SEM). The TLCP droplets in the extruded strands were seen with a progressive deformation into fibrillar structure when TLCP content was increased up to 30 wt%. In the extruded films, TLCP fibrils with increasing aspect ratio (length to width) were observed with increasing TLCP concentration. Orientation functions of each component were determined by X-ray diffraction using a novel separation technique. It was observed that the Young's modulus in machine direction of the extruded film was greatly improved with increasing TLCP loading, due to the increase in fiber aspect ratio and also molecular orientation.     

Preparation and characterization of modified telechelic natural rubber-based pressure-sensitive adhesive

Telechelic natural rubber (TNR) was prepared by the use of potassium persulfate and propanal at 70 °C and various degradation times from 0 to 30 h. These samples were then grafted by maleic anhydride (MA) in toluene solution before modification with 3-amino-1,2,4-triazole (ATA) to produce modified TNRs (AMTNRs). Attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) was used to identify the chemical compositions. Carboxyl and hydroxyl groups of TNRs were clearly observed, due to chain scission, oxidation, and modified chain ends. The viscosities of TNRs were dropped greatly after 5 h and then decreased slowly as a function of degradation time. ATR-FTIR spectra of AMTNRs showed amide bonds between ATA and MA groups, and then the multiple hydrogen bonding arrays were formed. The glass transition temperatures (T_g) of AMTNRs were determined by differential scanning calorimetry. The T_g of AMTNR_0 moved to a higher temperature of –55 °C after modification by ATA, confirming the formation of multiple hydrogen bonding arrays. However, the T_g of AMTNR_5 to AMTNR_30 decreased slightly due to chain scission in the degradation process. The adhesive properties of AMTNR-based pressure-sensitive adhesive were evaluated by a Lloyd adhesion tester. The tack of AMTNRs depended on wettability whereas peel and shear strengths were responded by a combination between wettability and multiple hydrogen bonding arrays.     

Thermally and electrochemically stable amorphous hole-transporting materials based on carbazole dendrimers for electroluminescent devices

Amorphous hole-transporting carbazole dendrimers, 1,4-bis[3,6-di(carbazol-9-yl)carbazol-9-yl]-2,6-di(2-ethylhexyloxy)benzene (G2CB) and 1,4-bis[3,6-di(carbazol-9-yl)carbazol-9-yl]-9-(2-ethylhexyl)carbazole (G2CC), were synthesized by a divergent approach involving bromination and Ullmann coupling reactions. Compounds G2CB and G2CC showed high thermal stability (T_g = 206 to 245 °C) and excellent electrochemical reversibility. Double-layer organic light-emitting diodes were fabricated by using G2CB and G2CC as hole-transporting layers (HTLs) and tris(8-quinolinato)aluminum (Alq₃) as light-emissive layer with the device configuration of indium tin oxide/HTL/Alq₃/LiF:Al. Both devices exhibited bright green emission from Alq₃. The device using G2CC as HTL has the best performance with a maximum brightness of 8900 cd/m² at 14 V and a low turn-on voltage of 3.5 V.     

Thermal decomposition kinetics of in situ reinforcing composite based on polypropylene and liquid crystalline polymer

A thermotropic liquid crystalline polymer (TLCP), a copolyester with a 80/20 molar ratio of p-hydroxy benzoic acid (HBA) and poly(ethylene terephthalate (PET), known as Rodrun LC5000, was melt blended with polypropylene (PP) using a twin-screw extruder. The thermal degradation of the blends containing various TLCP contents was investigated using thermogravimetry (TG). In nitrogen and in air, the TG profiles of PP revealed a single weight-loss step, whereas TLCP showed two and three major weight-loss steps in nitrogen and in air, respectively. In air, more complex TG curves were observed for the blends with TLCP loading. Simultaneous DSC thermograms revealed that the degradation processes for all neat polymers and the blends were endothermic in nitrogen and exothermic in air. The kinetic parameters (E_a, ln A, and n) calculated using isoconversional method indicated that the thermal stability of PP was significantly improved by in situ reinforcing with TLCP. Addition of SEBS-g-MA compatibilizer slightly enhanced the thermal resistance of blend.     

Atomic force microscopy investigation of phase morphology correlated with adhesive properties for modified telechelic natural rubber based-pressure sensitive adhesive

Atomic force microscopy (AFM) is a powerful technique to determine phase morphology and surface mechanical properties of materials. In this research natural rubber was degraded and grafted by malelic anhydride before modification with 3-amino-1,2,4-triazole to obtain modified telechelic natural rubber or modified TNR. It was then blended with cumarone-indene resin at 10, 30, and 50 phr, acting as tackifier. Phase morphology and surface topography were investigated by intermitted AFM. The results showed that tackifier enriched domains were clearly observed in modified TNR matrix after added 30 and 50 phr and the domain sizes were approximately to be the order of micrometer (5–10 µm) which it increased with increasing tackifier content. The intermolecular hydrogen bonding interaction between tackifier and modified TNR was observed by attenuated total reflectance Fourier transform infrared spectroscopy. The adhesive properties (loop tack, peel, and shear strength) were governed by the size of tackifier enriched domains, surface mean roughness and compatibility or interaction between modified TNR rubber and cumarone-indene tackifier resin.     

Synthesis of electrochemically and thermally stable amorphous hole-transporting carbazole dendronized fluorene

A novel amorphous hole-transporting carbazole dendrimer, 2,7-bis[3,6-di(carbazol-9-yl)carbazol-9-yl]-9,9-bis-n-hexylfluorene (G2CF), was synthesized by a divergent approach involving bromination and Ullmann coupling reactions. G2CF showed UV–vis absorption bands at 304 and 332 nm in chloroform solution and the photoluminescence spectra showed a maximum peak at 373 nm in a bluish-purple region. Differential scanning calorimetry (DSC) and cyclic voltammetry (CV) analysis revealed G2CF was an electrochemically and thermally stable amorphous material with a high glass transition temperature (T_g) of 237 °C. The organic light-emitting device having the structure of ITO/G2CF/Alq₃/LiF:Al exhibited a bright green emission with a maximum luminescence of 11,000 cd/m² at 16 V and a turn-on voltage of 5.4 V.     

A novel simulation of AC magnetic contactor based on electromagnetic transients program

This paper proposes a new simulation approach for the AC magnetic contactor using the electromagnetic transients program (EMTP). The duality transformation technique is applied to convert a magnetic model into an electrical model. The great advantages of the proposed model are its capability of being directly simulated with other electrical components using EMTP and, therefore, its minimum level of complexity. To enhance the precision of the proposed model, the saturation of magnetic core and the fringing flux effects are taken into account. The performance and accuracy of the proposed model are verified by comparing them with those from finite element method (FEM) simulations and experiments. The results confirm that the proposed model has very good performance and the technique can be further applied to other magnetic components. © 2014 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.