Simple chemical syntheses of TAG monohydroperoxides

For the purpose of synthesizing standards to be used in the quantification of TAG hydroperoxides, three TAG (1,2-dioleoyl-3-palmitoylglycerol, 1-oleoyl-2-linoleoyl-3-palmitoylglycerol, and triolein) monohydroperoxides were chemically synthesized as authentic specimens. TAG were prepared by using a simple condensation in pyridine of glycerol and the corresponding acid chlorides. These TAG were then converted into monohydroperoxides by a photosensitized peroxidation. The synthesized monohydroperoxides were analyzed by normal-phase and RP-HPLC. The results of normal-phase HPLC analysis showed that monohydroperoxides from a corresponding TAG were a mixture of regioisomers. In RP-HPLC, however, the regioisomers of monohydroperoxides were not separated and gave a single peak, which may improve the sensitivity for the detection of TAG monohydroperoxides. In this study TAG monohydroperoxide standards were synthesized; these will be useful for the study of yet unknown biological and pathological roles of TAG hydroperoxides.     

Clinical application of single-shot echo-planar diffusion-weighted imaging with compressed SENSE in prostate MRI at 3T: preliminary experience

Magnetic Resonance Materials in Physics, Biology and Medicine - Image quality (IQ) of diffusion-weighted imaging (DWI) with single-shot echo-planar imaging (ssEPI) suffers from low signal-to-noise...     

Wide Color Variation in SiNO Thin Films Dispersed with Precipitated TiN Nano Particles

Amorphous thin films of Ti_1?ySi_y(N,O) with y ≥ 0.38 were prepared by reactive sputter deposition in a nitrogen atmosphere. Thermal annealing of the films in an ammonia flow above 800°C yielded Si(N,O) amorphous thin films dispersed with precipitated TiN nanosized particles. The film color changed with Si content y and the annealing conditions, from carrot orange to cream yellow in the as‐deposited films due to their oxynitride nature, and from dark green to canary yellow and from iron blue to horizon blue at respective annealing temperatures of 800°C and 900°C due to metallic nature of the TiN nanosized particles precipitated in the annealing.     

Fracture behaviour and numerical study of resistance spot welded joints in high-strength steel sheet

Cross tension tests of resistance spot welded joints with varying nugget diameter were carried out using 980 MPa high strength steel sheet of 1.6 mm thickness. In proportion, as nugget diameter increased from 3√t to 5√t (where t is thickness), cross tension strength (CTS) increased while fracture morphology simultaneously transferred from interface fracture to full plug fracture. In cases of interface fracture, circumferential crack initiation due to separation of the corona bond arose at an early stage of loading. The crack opening process without propagation was recognized until just before fracture and then the crack propagated to the nugget immediately in a brittle manner around CTS. In full plug fracture, main ductile crack initiation from the notch-like part at the end of sheet separation occurred with the sub-crack initiated at an early stage. The ductile crack propagated toward the HAZ and base material to form full plug fracture. The mode I stress intensity factor was considered as a suitable fracture parameter because the circumferential crack behaved pre-crack for brittle fracture in the nugget region at the final stage. Based on the FE analysis, the mode I stress intensity factor was calculated as 116 MPa √m at CTS as fracture toughness for the nugget. With respect to full plug fracture, ductile crack initiation behaviour from the notch-like part was expressed by concentration of equivalent plastic strain. On the assumption that the ductile crack arose in critical value of equivalent plastic strain, the value was calculated as 0.34 by FE analysis. Reasonable interpretation for interface fracture and full plug fracture in the resistance spot welded joint was proposed due to first crack initiation by stress concentration, brittle fracture by using mode I stress intensity factor, and ductile crack initiation by using equivalent plastic strain.     

Additive Sintering,Postannealing, and Dielectric Properties of SrTaO2N

The maintaining of the chemical composition and electrical insulativity of SrTaO₂N ceramics was investigated during sintering and annealing, using powders prepared by the nitridation of Sr₂Ta₂O₇. Due to the low thermal stability of SrTaO₂N, the partial loss of SrO and nitrogen induced the formation of a TaO_0.9 impurity after heat‐treating at above 1100°C. The sintering additive SrCO₃ and postannealing in NH₃ were employed to compensate for the loss of SrO and nitrogen to obtain ceramics with the original chemical composition. The as‐sintered SrTaO₂N ceramics with various relative density (RD) were annealed in NH₃ to observe the recovery of color and electrical insulativity. It was found that the inner part of the well‐sintered samples with RD = 95.1% could not be recovered by annealing, and continued to exhibit semiconducting behavior and a black color. On the other hand, for the as‐sintered SrTaO₂N ceramics with RD < 84%, both the nitrogen content and electrically insulating behavior were completely recovered after annealing. The postannealed SrTaO₂N ceramics (RD = 83.3%) possessed a relatively large dielectric constant of 450 with a low dielectric loss of less than 0.1 at 100 Hz, almost independent of frequency and temperature.     

Fabrication of optics by use of plasma chemical vaporization machining with a pipe electrode

We figure optical surfaces by plasma chemical vaporization machining (CVM) with a pipe electrode, in which an rf plasma generated at the electrode tip under approximately atmospheric pressure moves over the surfaces. We propose a shaping method in which the movement of plasma on the surfaces can be determined. Flat and aspheric surfaces are successfully figured with the desired peak-to-valley shape accuracy of 0.1 microm. The root-mean-square roughness of the resultant surfaces is at the subnanometer level. These results confirm that the plasma CVM and the shaping method have the capability to fabricate optics with high accuracy.     

Niobium–aluminum oxynitride prepared by ammonolysis of oxide precursor obtained through the citrate route

Oxynitrides in the (Nb_1−xAl_x)(O,N) quaternary system were prepared by ammonolysis of oxide precursor obtained through the citrate route. The products at 1000 °C were a mixture of Nb(N,O) and NbN_0.95 at the niobium end (x = 0) and amorphous Al(O,N) at the aluminum end (x = 1). A new cubic compound (A) appeared mixed with Nb(N,O) in the compositional range 0.1 ≤ x ≤ 0.4. Its almost pure product was obtained at x = 0.5. The X-ray diffraction pattern was rock salt type (Nb_0.56Al_0.44)(O_0.38N_0.37□₀₂₅) in F_m−3m with a = 0.43481(1) nm. The product showed superconductivity with T_c = 15 K. Its crystallinity was much improved and its superconducting volume fraction increased to 32% after its thermal annealing at 1100 °C in evacuated sealed tube. A second cubic compound (B), rock salt type Nb[(O,N)_0.85□_0.15] with a = 0.434 nm, was observed mixed with amorphous Al(O,N) in the as-prepared products of the range 0.6 ≤ x ≤ 0.9.     

Difference in the detection limits of flaws in the depths of multi-layered and continuous aluminum plates using low-frequency eddy current testing

We examined the difference in the detection limits of flaws in the depths of multi-layered and continuous aluminum plates using low-frequency eddy current testing. The detection limits were measured by using a magneto-resistive sensor. Comparing the frequency of an applied magnetic field, the detection limit at 50 Hz is deeper than that at 1 kHz. Comparing the sample structure, the detection limit in the multi-layered samples is deeper than that in the continuous samples. These results are likely due to the differences in the skin depth and conductivity of the sample.     

Biomaterial-Assisted Regenerative Medicine

This review aims to show case recent regenerative medicine based on biomaterial technologies. Regenerative medicine has arousing substantial interest throughout the world, with “The enhancement of cell activity” one of the essential concepts for the development of regenerative medicine. For example, drug research on drug screening is an important field of regenerative medicine, with the purpose of efficient evaluation of drug effects. It is crucial to enhance cell activity in the body for drug research because the difference in cell condition between in vitro and in vivo leads to a gap in drug evaluation. Biomaterial technology is essential for the further development of regenerative medicine because biomaterials effectively support cell culture or cell transplantation with high cell viability or activity. For example, biomaterial-based cell culture and drug screening could obtain information similar to preclinical or clinical studies. In the case of in vivo studies, biomaterials can assist cell activity, such as natural healing potential, leading to efficient tissue repair of damaged tissue. Therefore, regenerative medicine combined with biomaterials has been noted. For the research of biomaterial-based regenerative medicine, the research objective of regenerative medicine should link to the properties of the biomaterial used in the study. This review introduces regenerative medicine with biomaterial.