Variations in fundamental frequency peak position in Japanese macaque (Macaca fuscata) coo calls.

Japanese macaques (Macaca fuscata) produce coo calls whose use in various contexts is correlated with differences in the relative temporal position of the peak value of a call's fundamental frequency (S. Green, 1975). Studies have produced conflicting results about both the location of the category boundary between smooth early high and smooth late high coo subtypes and macaques' perceptual sensitivity to variations in peak position. In this study, fundamental frequency peak positions were measured in 578 coos produced by 8 captive adult female Japanese macaques in order to test whether calls with peak positions close to either of 2 hypothesized boundaries occurred at low rates. Overall, such calls were found to occur at rates equal to or higher than predicted by chance. Peak position varied more consistently between animals than by behavioral context. The results may indicate that peak position in coos does not form 2 distinct categories. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Evaluation of Serum Volume Losses During Long-Term Storage

Aliquots of serum collected in a large case-control study of cervical cancer were stored at −70°C for up to 4 years during implementation of the study. When 500 μL serum aliquots were thawed in preparation for carotenoid and vitamin A assays, volumes were noticeably variable and fell below 500 μL in the majority of the samples. We were concerned about evaporation/sublimation during storage of the samples because loss of water would concentrate the analytes of interest. We evaluated the use of density and sodium ion concentration measurements to confirm its occurrence. We found that serum density was an unreliable indicator of extent of volume loss since the anticipated increases in density due to evaporation were of the same magnitude as inter-individual variation in serum density. In contrast, Na⁺ concentration is tightly regulated and would rise if water had been lost from the samples. In a representative sample of serum aliquots from the case-control study, 24 of 25 vials contained less than 500 μL of serum. The mean sodium ion concentration (138.1 ± 3.6 mmol/L) was within the normal range for human serum of 136–145 mmol/L, and no correlation was observed between serum volume and Na⁺ concentration. These results strongly suggest that the observed low volumes were not due to evaporative losses. Instead, the variably low volumes of serum aliquots were probably due to pipetting errors in the initial aliquotting resulting from the use of air-displacement pipettes.     

Trends in low flows of German rivers since 1950: Comparability of different low‐flow indicators and their spatial patterns

Climate change, land‐use shifts, reservoir storage, and water withdrawals impact low flows in rivers, creating challenges for ecological integrity and human uses. A systematic investigation of river discharges was carried out for 79 stream gauges in Germany. Available time series between 1950 and 2013 were analysed for trends in annual minimum low flows, discharge deficits, and low‐flow durations. The application of different low‐flow indicators led to similar spatial patterns, although each metric is used for different purposes in water management applications. Statistical tests identified significant discharge trends at more than half of the stations investigated. Low‐flow trends since 1950 tended to be catchment specific, suggesting that climate change has not been the dominant driver. Most of the gauges investigated showed statistically significant increases in low flows. This can be mainly attributed to reservoir management. For rivers showing snow‐ and icemelt‐dominated flow regimes, such trends are probably overlain by climate‐driven changes (increasing amounts of rainfall, earlier snowmelt in spring). In contrast, stations showing statistically significant decreases in low flows were correlated with areas of decreasing mining activity. Hydrologic impacts of climate change are widespread and significant, but the results here suggest that human river management remains the dominant hydrologic driver on many rivers.     

The effect of cooling rate on the impact performance and dynamic mechanical properties of rotationally molded metallocene catalyzed linear low density polyethylene

This article examines changes to the morphology of rotationally molded metallocene catalyzed linear low density polyethylene brought about by varying the cooling rate during processing. These changes in morphology lead to variations in the impact performance, which is reflected in the dynamic mechanical characteristics of the materials. Various analytical techniques are used in an attempt to explain the differences in impact behavior. Slow cooling is shown to result in high crystallinity, and in the formation of large spherulites, which in turn is detrimental to the impact performance of the material, particularly at low temperatures. The high crystallinity corresponds with a shift in the β transition of the material to a higher temperature, and is shown to result in a higher brittle–ductile transition. A case study was also carried out on samples from a finished part provided by an industrial molder, one section of which failed in a brittle manner when impact tested while the other failed in a ductile manner. Microscopy results showed that the brittle material had large spherulites at the inside surface, while the ductile material showed incipient degradation at this surface, which has previously been shown to be of benefit to impact strength in rotationally molded parts. Dynamic mechanical studies again showed a β transition at a higher temperature in the brittle samples. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1963–1971, 2006     

The Quasi-static Deformation, Failure, and Fracture Behavior of Titanium Alloy Gusset Plates Containing Bolt Holes

In this article, the influence of bolt holes, specifically their number and layout on strength, deformation, and final fracture behavior of titanium alloy gusset plates under the influence of an external load is presented and discussed. Several plates having differences in both the number and layout of the bolt holes were precision machined and then deformed under quasi-static loading. The specific influence of number of bolt holes and their layout on maximum load-carrying capability and even fracture load was determined. The conjoint influence of bolt number, bolt layout pattern, nature of loading, contribution from local stress concentration, and intrinsic microstructural effects in governing the macroscopic fracture mode and intrinsic microscopic mechanisms is presented and discussed.