Anti‐Sway Crane Control Considering Wind Disturbance and Container Mass

A method for estimating the sway angle using an observer has already been proposed. The state observer estimates the sway angle accurately and must use the detected sway angle value. However, the estimated sway angle has an error owing to rope length error, friction force, and wind. Moreover, the container mass cannot be determined, and therefore the observer parameter is not suitable. We already proposed robust antisway control for overcoming rope length error without adding a new sensor. Further, we designed a friction disturbance observer to cancel out the influence of the friction force. In this paper, we first propose a container mass estimation method when a crane system performs rolling up control. The observer parameter can be selected using the estimated mass value. Second, in crane parallel shift control, we propose a robust antisway control even when there is a wind disturbance. We design a wind disturbance observer and propose a wind disturbance estimator to separate the friction observer output from the wind disturbance observer output. We confirm through experiments that the proposed method can reduce vibration.     

Improved atrial function in bicaval versus standard orthotopic techniques in cardiac transplantation

Atrial geometry is preserved in the bicaval technique of cardiac transplantation. Using Doppler echocardiography, we investigated the impact of this technique on preservation of atrial function and found that echocardiographic indexes of atrial function are improved in bicaval cardiac transplants versus the standard orthotopic transplants.     

Aortic valve papillary fibroelastoma. A diagnosis by transthoracic echocardiography

Cardiac papillary fibroelastomas are unusual, frond-like growths typically found on cardiac valves, diagnosed incidentally on autopsy or cardiac surgery, but rarely during life. We report a rare case of an aortic valve papillary fibroelastoma detected by transthoracic echocardiography and confirmed by histologic study.     

Radiation detector made of a high-quality polycrystalline diamond

Radiation detector was made of a high-quality CVD polycrystalline diamond composed of frost column like structure diamond grains, and induced charge distribution spectra and drift velocities were measured by using alpha particles. As a result, the CVD polycrystalline achieved maximum induced charge of 83% of HP/HT type IIa diamond. Moreover, the CVD crystal had lower charge loss on electrons compared with the HP/HT type IIa diamond. Drift velocities of electrons and holes were v_e = 7.7 × 10⁴ and v_h = 7.3 × 10⁴cm/s at an electric field of 20 kV/cm, respectively. In addition, response function measurement for 14 MeV neutrons was carried out.     

A feasibility study of a direct-mapping parallel processing method to solve linear equations in load-flow calculation

With the growing size and complexity of power systems, system analysis—such as transients calculation—takes much time. Hence, fast calculation methods are required. Although parallel processing is a hopeful method, there have been difficulties in the parallel solution of linear equations which appear in power-flow calculations by the Newton-Raphson method. This paper aims at the fast calculation of the power-flow problem by means of parallel processing. In order to improve the suitability to the parallel solution of the differential equation in transients calculation, we assume the use of a direct-mapping parallel processing machine to map directly the network of a power system onto a network of processors. Under this assumption, we propose a new parallel-processing-oriented method in which the linear equation is solved by linear iterations between nodes with Aitken acceleration. We simulate the method on three model power systems and compare this Parallel Iterative Method (PIN) with a Parallel Direct Method (PDM) which uses the banded matrix according to the number of operations required. As a result, we can expect that PIM may solve linear equations faster than PDM with m processors, although the PIM might be inferior to the PDM with m × m processors, where m denotes the half-band width of the banded matrix.     

Molecular Dynamics Simulation of Structural Relaxation of Asphaltene Aggregates

For asphaltene obtained from vacuum residue of Khafji crude oil, the energy-minimum conformation calculated by molecular mechanics-dynamics simulations showed that aggregated structures of asphaltene molecules through noncovalent interactions are more stable. Changes induced in aggregated structures by pretreatment with solvents were investigated using molecular dynamics calculations. The simulation showed that in quinolin at 573 K, some staking interactions could be disrupted, while, in 1-methylnaphthalene it was not observed. Autoclave experiments showed that the coke yield after pyrolysis at 713 K was decreased when the asphaltene was pretreated with quinoline at 573 K for 1 h, compared to the yield without the pretreatment. While, in the case of pretreatment in 1-methylnaphthalene, the coke yield did not change significantly. The simulation's results above can be related to the difference in coke yield between two solvents; in quinoline some aromatic-aromatic stacking interactions could be disrupted and mobility of molecules was increased. This resulted in prevention of the asphaltenes from polymerizing, as in condensation reactions among aromatic rings. Consequently, the coke yield after the pretreatment with quinoline was decreased.     

Augmenting Edge-Connectivity between Vertex Subsets

Given a directed or undirected graph G=(V,E), a collection ${\mathcal{R}}=\{(S_{i},T_{i}) \mid i=1,2,\ldots,|{\mathcal{R}}|, S_{i},T_{i} \subseteq V, S_{i} \cap T_{i} =\emptyset\}$ of two disjoint subsets of V, and a requirement function $r: {\mathcal{R}} \to\mathbb{R}_{+}$ , we consider the problem (called area-to-area edge-connectivity augmentation problem) of augmenting G by a smallest number of new edges so that the resulting graph $\hat{G}$ satisfies $d_{\hat{G}}(X)\geq r(S,T)$ for all X?V, $(S,T) \in{\mathcal{R}}$ with S?X?V?T, where d _G (X) denotes the degree of a vertex set X in G. This problem can be regarded as a natural generalization of the global, local, and node-to-area edge-connectivity augmentation problems. In this paper, we show that there exists a constant c such that the problem is inapproximable within a ratio of $c\log{|{\mathcal{R}}|}$ , unless P=NP, even restricted to the directed global node-to-area edge-connectivity augmentation or undirected local node-to-area edge-connectivity augmentation. We also provide an ${\mathrm{O}}(\log{|{\mathcal{R}}|})$ -approximation algorithm for the area-to-area edge-connectivity augmentation problem, which is a natural extension of Kortsarz and Nutov’s algorithm (Kortsarz and Nutov, J. Comput. Syst. Sci., 74:662–670, 2008). This together with the negative result implies that the problem is ${\varTheta}(\log{|{\mathcal{R}}|})$ -approximable, unless P=NP, which solves open problems for node-to-area edge-connectivity augmentation in Ishii et al. (Algorithmica, 56:413–436, 2010), Ishii and Hagiwara (Discrete Appl. Math., 154:2307–2329, 2006), Miwa and Ito (J. Oper. Res. Soc. Jpn., 47:224–243, 2004). Furthermore, we characterize the node-to-area and area-to-area edge-connectivity augmentation problems as the augmentation problems with modulotone and k-modulotone functions.     

Microstructure of TiO2 and ZnO Films Fabricated by the Sol-Gel Method

Titanium dioxide and zinc oxide films were fabricated by spin-on and dip-coating methods. Both types of films exhibited columnar grains when the single coating was thin, ∼10 nm. The columnar TiO₂ films were dense, as confirmed by their density values calculated from the refractive index and TEM results. The addition of Al cations into the ZnO suppressed grain growth, because Zn had a lower diffusivity in the doped films. The doped ZnO films had nearly the same electrical resistivity as that of the undoped films.     

Observation of single-walled carbon nanotubes by photoemission microscopy

Single-walled carbon nanotube networks grown on SiO₂ pillars were studied by means of scanning photoemission microscopy. The individual nanotubes or nanotube bundles growing from the pillar tops were observed in C 1s images. Band bending near catalytic Fe/nanotube contacts in an end-bonded configuration was studied by measuring C 1s spectra along the tube axes. Within our experimental resolution, no band bending was observed. This implies that the depletion width is less than the spatial resolution of the scanning photoemission microscope (90 nm) or that the amount of the band bending is less than 0.1 eV.