Aluminium content of foods originating from aluminium-containing food additives

Aluminium (Al) levels of 90 food samples were investigated. Nineteen samples contained Al levels exceeding the tolerable weekly intake (TWI) for young children [body weight (bw): 16 kg] when consuming two servings/week. These samples were purchased multiple times at specific intervals and were evaluated for Al levels. Al was detected in 27 of the 90 samples at levels ranging from 0.01 (limit of quantitation) to 1.06 mg/g. Of these, the Al intake levels in two samples (cookie and scone mix, 1.3 and 2 mg/kg bw/week, respectively) exceeded the TWI as established by European Food Safety Authority, although the level in the scone mix was equivalent to the provisional TWI (PTWI) as established by Joint Food and Agriculture Organization of the United Nations/World Health Organization Expert Committee on Food Additives. The Al levels markedly decreased in 14 of the 19 samples with initially high Al levels. These results indicated reductions in the Al levels to below the PTWI limits in all but two previously identified food samples.     

The calculation of particle deposition efficiency due to inertia,diffusion and interception in a plane stagnation flow

The particle deposition mechanism in a plane stagnation flow is investigated analytically and numerically. Particle deposition efficiency η_TID is obtained theoretically by taking into account particle inertia, diffusion and interception. It is compared with various calculated deposition efficiencies, i.e. η_T (due to inertia) + η_I (due to interception) + η_D (due to diffusion), η_TI, (due to inertia and interception) + η_D, etc. In the region where all of the three deposition mechanisms, i.e. inertia, interception and diffusion, act at the same time, real deposition efficiency η_TID is not accurately expressed by η_T + η_I + η_D. However, η_TID is nearly equal to η_TI + η_D unless the interception parameter is zero.The calculated results of particle concentration indicate that a high concentration region is formed near the deposition plate, and that the concentration becomes higher as particle inertia increases.     

Fourier synthesis image reconstruction by use of one-dimensional position-sensitive detectors

An improvement of Fourier synthesis optics for hard x-ray imaging is described, and the basic performance of the new optics is confirmed through numerical simulations. The original concept of the Fourier synthesis imager utilizes nonposition-sensitive hard x-ray detectors coupled to individual bigrid modulation collimators. The improved concept employs a one-dimensional position-sensitive detector (such as a CdTe strip detector) instead of the second grid layer of each bigrid modulation collimator. This improves the imaging performance in several respects over the original design. One performance improvement is a two-fold increase in the average transmission, from 1/4 to 1/2. The second merit is that both the sine and cosine components can be derived from a single grid-detector module, and hence the number of imaging modules can be halved. Furthermore, it provides information along the depth direction simultaneously. This in turn enables a three-dimensional imaging hard x-ray microscope for medical diagnostics, incorporating radioactive tracers. A conceptual design of such a microscope is presented, designed to provide a field of view of 4 mm and a spatial resolution of 400 microm.     

Ultrasonic techniques for imaging and measurements in molten aluminum

In order to achieve net shape forming, processing of aluminum (Al) in the molten state is often necessary. However, few sensors and techniques have been reported in the literature due to difficulties associated with molten Al, such as high temperature, corrosiveness, and opaqueness. In this paper, development of ultrasonic techniques for imaging and measurements in molten Al using buffer rods operated at 10 MHz is presented. The probing end of the buffer rod, having a flat surface or an ultrasonic lens, was immersed into molten Al while the other end with an ultrasonic transducer was air-cooled to room temperature. An ultrasonic image of a character "N", engraved on a stainless steel plate immersed in molten Al, and its corrosion have been observed at 780 degrees C using the focused probe in ultrasonic pulse-echo mode. Because cleanliness of molten Al is crucial for part manufacturing and recycling in Al processing, inclusion detection experiments also were carried out using the nonfocused probe in pitch-catch and pulse-echo modes. Backscattered ultrasonic signals from manually added silicon carbide particles, with an average diameter of 50 microm, in molten Al have been successfully observed at 780 degrees C. For optimal image quality, the spatial resolution of the focused probe was crucial, and the high signal-to-noise ratio of the nonfocused probe was the prime factor responsible for the inclusion detection sensitivity using backscattered ultrasonic signals. In addition, it was found that ultrasound could provide an alternative method for evaluating the degree of wetting between a solid material and a molten metal. Our experimental results showed that there was no ultrasonic coupling at the interface between an alumina rod and molten Al up to 1000 degrees C; therefore, no wetting existed at this interface. Also because ultrasonic velocity in alumina is temperature dependent, this rod proved to be able to be used as an in-line temperature monitoring sensor under 1000 degrees C in molten Al.     

Collection of submicron particles in electro-flotation

A theoretical analysis is presented to describe the deposition of Brownian particles onto hydrogen bubbles under surface interactions. Single collection efficiency has been numerically calculated for zeta potentials, having assumed that the effective Hamaker constant is equal to 3.0 × 10^?14erg though our choice of Hamaker constant is rather arbitrary. From a mass balance, total collection efficiency or the rate of flotation has been determined. In this way, electro-flotation process is quantitatively described.Experimentally, the electro-flotation of polystyrene latices of mean diameter 0.6 μm has been studied to examine the effect of the charge on both particles and bubbles on the total collection efficiency. The bubbles were of mean diameter 20 μm. The electrolyte was AlCl₃. To measure the charge on the bubbles, we directly sampled solution including very small bubbles with a glass tube from a flotation vessel and poured into a micro-electrophoresis cell. The horizontal velocity measured when the bubbles rose up a “stationary level” in the cell under the known potential gradient gave the electromobility. The charge on the latex particles were found to change its sign from negative to positive as flotation time went on.The theoretical total collection efficiency has been in close agreement with the experimentally determined one.     

Leaching test of gamma-emitting Cs,Ru, Zr,and U from neutron-irradiated UO2/ZrO2 solid solutions in non-filtered surface seawater

The leaching behaviors of gamma-ray radionuclides, Cs-137, Ru-103, and Zr-95, produced by neutron irradiation of UO₂/ZrO₂ solid solutions, in real surface seawater were investigated under atmospheric conditions. The fraction of radionuclide inventory leached in the seawater was in the order of Cs > Ru (～U) ? Zr, indicating that the fraction was significantly affected by the chemical state of the radionuclides. However, the amount of soluble nuclides was proportional to that of uranium regardless of whether the solid solutions were prepared under an oxidative or reductive environment. A tiny fraction of Ru was filtered out by a 3 kDa nominal molecular weight cut-off filter after the 160 d leaching test, suggesting a different behavior from its ionic form, but Cs and U did not form a colloid-like species in seawater.     

In Situ Observation of Phase Separation of a Barium Borate Melt in a Stable Immiscibility Region under Microgravity

The precipitation of droplets was directly observed on a BaO–B₂O₃ melt in a drop shaft experiment. This is the first time that precipitation of droplets has been observed in a 4.5 s drop test. The melt film of 4BaOz96B₂O₃ (mol%) held on a platinum wire loop was heated above the critical tem-perature to produce uniformity and was cooled down to the phase separation temperature range. Phase separation of the melt was observed directly with a video camera. The IR image of the melt was simultaneously detected with a CCD array and was converted into a two-dimensional thermograph.     

Performance of the first Japanese large-scale facility for radon inhalation experiments with small animals

A radon test facility for small animals was developed in order to increase the statistical validity of differences of the biological response in various radon environments. This paper illustrates the performances of that facility, the first large-scale facility of its kind in Japan. The facility has a capability to conduct approximately 150 mouse-scale tests at the same time. The apparatus for exposing small animals to radon has six animal chamber groups with five independent cages each. Different radon concentrations in each animal chamber group are available. Because the first target of this study is to examine the in vivo behaviour of radon and its effects, the major functions to control radon and to eliminate thoron were examined experimentally. Additionally, radon progeny concentrations and their particle size distributions in the cages were also examined experimentally to be considered in future projects.     

Coexisting state of surge and rotating stall in a two-stage axial flow compressor using a double-phase-locked averaging technique

The interaction between surge and rotating stall in an axial flow compressor was investigated from the viewpoint of an unsteady inner flow structure. The aim of this study was to identify the key factor that determines the switching phenomenon of a surge cycle. The main feature of the tested compressor is a shock tube connected in series to the compressor outlet through a diaphragm, slits, and a concentric duplex pipe: this system allows surge and rotating stall to be generated by connecting the shock tube with the compressor, or enables the compression plane wave injection. The unsteady characteristics and the internal flow velocity fluctuations were measured in detail, and the stall cell structure was averaged and visualized along the movement of the operation point under a coexisting state of surge. A coefficient of the cell scale fluctuation was calculated using the result of the averaging, and it confirmed that the processes of inner flow structure change differed from each other according to the next cycle of the surge. The result suggests that the key factor that determines the next cycle is the transformation of the internal flow structure, particularly between the stall cell and the entire circumferential stall, in both the recovering and stalling processes.     

Optimizing process allocation of parallel programs for heterogeneous clusters

The performance of a conventional parallel application is often degraded by load‐imbalance on heterogeneous clusters. Although it is simple to invoke multiple processes on fast processing elements to alleviate load‐imbalance, the optimal process allocation is not obvious. Kishimoto and Ichikawa presented performance models for high‐performance Linpack (HPL), with which the sub‐optimal configurations of heterogeneous clusters were actually estimated. Their results on HPL are encouraging, whereas their approach is not yet verified with other applications. This study presents some enhancements of Kishimoto's scheme, which are evaluated with four typical scientific applications: computational fluid dynamics (CFD), finite‐element method (FEM), HPL (linear algebraic system), and fast Fourier transform (FFT). According to our experiments, our new models (NP‐T models) are superior to Kishimoto's models, particularly when the non‐negative least squares method is used for parameter extraction. The average errors of the derived models were 0.2% for the CFD benchmark, 2% for the FEM benchmark, 1% for HPL, and 28% for the FFT benchmark. This study also emphasizes the importance of predictability in clusters, listing practical examples derived from our study. Copyright © 2008 John Wiley & Sons, Ltd.