Laboratory Studies to Determine Suitable Chemicals to Improve Oil Recovery from Garzan Oil Field

Garzan oil field is located at the south east of Turkey. It is a mature oil field and the reservoir is fractured carbonate reservoir. After producing about 1% original oil in place (OOIP) reservoir pressure started to decline. Waterflooding was started in order to support reservoir pressure and also to enhance oil production in 1960. Waterflooding improved the oil recovery but after years of flooding water breakthrough at the production wells was observed. This increased the water/oil ratio at the production wells. In order to enhance oil recovery again different techniques were investigated. Chemical enhanced oil recovery (EOR) methods are gaining attention all over the world for oil recovery. Surfactant injection is an effective way for interfacial tension (IFT) reduction and wettability reversal. In this study, 31 different types of chemicals were studied to specify the effects on oil production. This paper presents solubility of surfactants in brine, IFT and contact angle measurements, imbibition tests, and lastly core flooding experiments. Most of the chemicals were incompatible with Garzan formation water, which has high divalent ion concentration. In this case, the usage of 2-propanol as co-surfactant yielded successful results for stability of the selected chemical solutions. The results of the wettability test indicated that both tested cationic and anionic surfactants altered the wettability of the carbonate rock from oil-wet to intermediate-wet. The maximum oil recovery by imbibition test was reached when core was exposed 1-ethly ionic liquid after imbibition in formation water. Also, after core flooding test, it is concluded that considerable amount of oil can be recovered from Garzan reservoir by waterflooding alone if adverse effects of natural fractures could be eliminated.     

Microstructure,wear and corrosion characteristics of multiple-reinforced (SiC–B4C–Al2O3) Al matrix composites produced by liquid metal infiltration

In this study, AA7075 aluminum matrix composites reinforced with the combination of SiC, Al₂O₃, and B₄C particles were fabricated by the liquid metal infiltration method. The effects of the relative ratio of B₄C and Al₂O₃ particles on the microstructural, wear, and corrosion features of the composite samples were analyzed using XRD, light metal microscopy, SEM, EDS, Brinell hardness, ball-on-disc type tribometer, and potentiodynamic polarization devices. It was determined that infiltration occurred more successfully, and homogenously distributed particles with reduced porosity were obtained as the amount of Al₂O₃ increased. Worn surface studies revealed that the specimens were predominantly worn by abrasion and adhesion. The increase in B₄C/Al₂O₃ ratio caused a decrease in the hardness and wear strength, whereas it increased the corrosion resistance.     

Flexible poly(styrene-ethylene-butadiene-styrene) hybrid nanofibers for bioengineering and water filtration applications

Among the thermoplastic elastomers that play important roles in the polymer industry due to their superior properties, styrene-based species and polyurethane block copolymers are of great interest. Poly(styrene-ethylene-butadiene-styrene) (SEBS) as a triblock copolymer seems to have the potential to meet many demands in different applications due to various industrial requirements where durability, biocompatibility, breaking elongation, and interfacial adhesion are important. In this study, the SEBS triblock copolymer was functionalized with natural (Satureja hortensis, SH) and synthetic (nanopowder, TiO₂) agents to obtain composite nanofibers by electrospinning and electrospraying methods for use in biomedical and water filtration applications. The results were compared with thermoplastic polyurethane (TPU) composite nanofibers, which are commonly used in these fields. Here, functionalized SEBS nanofibers exhibited antibacterial effect while at the same time improving cell viability. In addition, because of successful water filtration by using the SEBS composite nanofibers, the material may have a good potential to be used comparably to TPU for the application.     

Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

Production of hydrogen over bimetallic Pt–Ni/δ-Al2O3: I. Indirect partial oxidation of propane

Indirect partial oxidation (IPOX) of propane was studied over bimetallic 0.2 wt.% Pt–15 wt.% Ni/δ-Al₂O₃ catalyst in the 623–743 K temperature range. The unreduced and reduced forms of the catalyst were characterized by ESEM–EDAX and X-ray diffraction (XRD). In the IPOX tests, the effects of steam to carbon ratio (S/C), carbon to oxygen ratio (C/O₂) and residence time (W/F (g_cat h/mol HC)) on the hydrogen production activity, selectivity and product distribution were studied in detail. The effect of temperature program applied (increasing from 623 to 743 K, ITP; decreasing from 743 to 623 K, DTP) during reaction was also tested. The results showed that the Pt–Ni bimetallic system has superior performance characteristics compared to the monometallic catalysts reported in literature. The reason is thought to be the utilization of the catalyst particles as micro heat exchangers during IPOX; the heat generated by Pt sites during exothermic total oxidation (TOX) being readily transferred through the catalyst particles acting as micro heat exchangers to the Ni sites, which promote endothermic steam reforming (SR). The optimal conditions were found as S/C = 3, C/O₂ = 2.70 and W/F = 0.51 g_cat h/mol HC for IPOX of propane on the basis of high hydrogen productivity and selectivity between 623 and 748 K for the experimental conditions tested. The thermo-neutral points obtained showed the sustainability of reaction in terms of energy.     

Electrical and optical properties of fluorine-doped CdO films deposited by ultrasonic spray pyrolysis

The CdO:F samples have been deposited onto microscope glass substrates at 250 °C by ultrasonic spray pyrolysis method. With the incorporation of fluorine into CdO, the direct optical transition has shifted towards the shorter wavelengths, and the transparency of the material has increased at a given wavelength above the fundamental absorption edge. The shift in the absorption edge is explained by means of the Moss–Burstein effect, which is also supported with the results of the current–voltage characteristics. Here, a correlation has been established between the band broadening and the increase in conductivity due to the increase in carrier density.     

Theoretical Investigation of Time Suboptimal Control of Industrial Manipulators Along Specified Paths

A method for the time suboptimal control of an industrial manipulator from an initial position and orientation to a final position and orientation as it moves along a specified path is proposed. Nonlinear system equations that describe the manipulator motion are linearized at each time step along the path. A method which gives the control inputs (joint angular velocities) for time suboptimal control of the manipulator is developed. In the formulation, joint angular velocity and acceleration limitations are also taken into consideration. A six degree of freedom elbow type manipulator is used in numerical examples to verify the method developed.