Investigation of the changes in physical properties of PES/PVC fabrics after aging

The aim of this work was to investigate the physical and mechanical performance of architectural polyester (PES)–poly(vinyl chloride) (PVC) membranes exposed to different artificial aging conditions. Two commercially available architectural membranes were chosen as research objects. The durability of the PES/PVC fabrics was evaluated by the loss in mechanical performance, scanning electron microscopy, and X-ray diffraction analysis in order to understand the effect of the degradation agents on the surface of the membranes. The mechanical performance of the PES/PVC membranes was unchanged. Scanning electron microscopy images of the tested materials showed initial cracks after aging. The X-ray fluorescence analysis showed that at the time of aging, the amount of Cl and Si decreased slightly, while Ti decreased by half, and Ca by volume increased twice. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47523.     

Nanolayer CrAlN/TiSiN coating designed for tribological applications

With the goal to produce a hard and tough coating intended for tribological applications, CrAlN/TiSiN nanolayer coating was prepared by alternative deposition of CrAlN and TiSiN layers. In the first part of the article, a detailed study of phase composition, microstructure, and layer structure of CrAlN/TiSiN coating is presented. In the second part, its mechanical properties, fracture and tribological behavior are compared to the nanocomposite TiSiN coating. An industrial magnetron sputtering unit was used for coating deposition. X-ray photoelectron spectroscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used for compositional and microstructural analysis. Mechanical properties and fracture behavior were studied by instrumented indentation and focused ion beam techniques. Tribological properties were evaluated by ball-on-disk test in a linear reciprocal mode. A complex layer structure was found in the nanolayer coating. The TiSiN layers were epitaxially stabilized inside the coating which led to formation of dislocations at interfaces, to introduction of disturbances in the coating growth, and as a result, to development of fine-grained columnar microstructure. Indentation load required for the onset of fracture was twice lower for the nanolayer CrAlN/TiSiN, compared to the nanocomposite TiSiN coating. This agrees very well with their mechanical properties, with H³/E² being twice higher for the TiSiN coating. However, the nanolayer coating experienced less severe damage, which had a strong impact on tribological behavior. A magnitude of order lower wear rate and four times lower steady state friction coefficient were found for the nanolayer coating.     

Formulation of sage essential oil (Salvia officinalis,L.) monoterpenes into chitosan hydrogels and permeation study with GC-MS analysis

This study deals with the formulation of natural drugs into hydrogels. For the first time, compounds from the sage essential oil were formulated into chitosan hydrogels. A sample preparation procedure for hydrophobic volatile analytes present in a hydrophilic water matrix along with an analytical method based on the gas chromatography coupled with the mass spectrometry (GC-MS) was developed and applied for the evaluation of the identity and quantity of essential oil components in the hydrogels and saline samples. The experimental results revealed that the chitosan hydrogels are suitable for the formulation of sage essential oil. The monoterpene release can be effectively controlled by both chitosan and caffeine concentration in the hydrogels. Permeation experiment, based on a hydrogel with the optimized composition [3.5% (w/w) sage essential oil, 2.0% (w/w) caffeine, 2.5% (w/w) chitosan and 0.1% (w/w) Tween-80] in donor compartment, saline solution in acceptor compartment, and semi-permeable cellophane membrane, demonstrated the useful permeation selectivity. Here, (according to lipophilicity) an enhanced permeation of the bicyclic monoterpenes with antiflogistic and antiseptic properties (eucalyptol, camphor and borneol) and, at the same time, suppressed permeation of toxic thujone (not exceeding its permitted applicable concentration) was observed. These properties highlight the pharmaceutical importance of the developed chitosan hydrogel formulating sage essential oil in the dermal applications.     

Stress distribution in thick-walled cylinder due to non-uniform radial pressure on the example of reinforcement corrosion in concrete

This paper presents an analytical solution to the non-uniform pressure on thick-walled cylinder. The formulation is based on the linear elasticity theory (plain strain) and stress function method. As an example, the proposed solution is used to model the stress distribution due to non-uniform steel reinforcement corrosion in concrete. The model is formulated considering different scenarios of corrosion pressure distribution. It is validated against the finite element model for different cases of non-uniform pressure distributions. The results show that the corrosion-induced cracks are likely to start just beyond the anodic zone. This is confirmed by the experimental tests on concrete cylinder exposed to non-uniform accelerated corrosion of steel reinforcement. The model can be effectively used to calculate the distribution of corrosion-induced stresses in concrete.     

Evaluation of microbial toxins,trace elements and sensory properties of a high-theabrownins instant Pu-erh tea produced using Aspergillus tubingensis via submerged fermentation

Theabrownins (TB) are polymeric phenolic compounds associated with the multiple bioactivities of Pu-erh tea, a post-fermented Chinese dark tea. High-TB instant Pu-erh tea was produced via a novel submerged fermentation (SF) using Aspergillus tubingensis and compared with samples produced commercially via the conventional solid-state fermentation (SSF). Viable microorganisms and microbial toxins, especially aflatoxins B₁, G₁, B₂, G₂, cyclopiazonic acid, fumonisins B₁, B₂, B₃ and ochratoxin A, were below the detection limit in all samples. Fewer microbial metabolites were found in SF instant tea compared with the SSF teas. Based on an adult consuming 1 g of instant Pu-erh tea daily, the dietary intake of investigated elements was below the safe limits recommended by various authorities. Tasters viewed the instant tea infusions as very mild, smooth, mellow and full. This suggested that submerged fermentation using A. tubingensis offers a speedy and safe alternative to commercial production of instant Pu-erh tea.     

Life expectancies of Pb-free SAC solder interconnects in electronic hardware

The transition from lead (Pb) bearing solder to Pb-free solder has arisen in response to government restrictions on the use of lead (Pb) by the European Union. As a result, electronic manufacturers have sought a material comparable to the conventional 63Sn37Pb solder that has been traditionally used to assemble electronic hardware. Based on extensive review of various solder combination, the majority of electronic manufacturers appear to be adopting a tin–silver–copper (SAC) solder as a popular Pb-free solder replacement. Significant investments have been made by many researchers to characterize the material behavior and durability of this solder system. While the exact composition of the SAC solder is still in question, it now appears that the 96.5Sn3.0Ag0.5Cu (SAC305) solder is gaining wider acceptance as the favored Pb-free replacement, for surface mount assemblies that are going to be subjected predominantly to cyclic thermal environments. This paper presents a review of our current understanding of the life expectancy of Pb-free SAC solder interconnects for electronic hardware. To this end, the paper focuses on material characterization of SAC solder, as well as its temperature cycling and vibration fatigue reliability. From this review, SAC solder interconnects are shown to be suitable for providing adequate life expectancies for temperature cycling in electronic hardware. However, it is clear that there are differences between SAC and the conventional Sn37Pb solder, that need to be understood in order to design reliable electronic hardware.     

US-guided pseudoaneurysm repair with a compression device

A simple commercially available compression device allowed intermittent ultrasound scanning of the compression site during compression repair of a femoral artery pseudoaneurysm in six patients. All six of the pseudoaneurysms (five superficial femoral and one common femoral) were compressed without compression of the underlying vessels. The procedure was successful in four of the six patients, without complications. Use of this device may decrease operator fatigue during compression repair of pseudoaneurysm.     

Asymptotic stress intensity factor density profiles for smeared-tip method for cohesive fracture

The paper presents a computational approach and numerical data which facilitate the use of the smeared-tip method for cohesive fracture in large enough structures. In the recently developed K-version of the smeared tip method, the large-size asymptotic profile of the stress intensity factor density along a cohesive crack is considered as a material characteristic, which is uniquely related to the softening stress-displacement law of the cohesive crack. After reviewing the K-version, an accurate and efficient numerical algorithm for the computation of this asymptotic profile is presented. The algorithm is based on solving a singular Abel's integral equation. The profiles corresponding to various typical softening stress-displacement laws of the cohesive crack model are computed, tabulated and plotted. The profiles for a certain range of other typical softening laws can be approximately obtained by interpolation from the tables. Knowing the profile, one can obtain with the smeared-tip method an analytical expression for the large-size solution to fracture problems, including the first two asymptotic terms of the size effect law. Consequently, numerical solutions of the integral equations of the cohesive crack model as well as finite element simulations of the cohesive crack are made superfluous. However, when the fracture process zone is attached to a notch or to the body surface and the cohesive zone ends with a stress jump, the solution is expected to be accurate only for large-enough structures.