Multiply Charged Conjugated Polyelectrolytes as a Multifunctional Interlayer for Efficient and Scalable Perovskite Solar Cells

A series of anionic conjugated polyelectrolytes (CPEs) is synthesized based on poly(fluorene-co-phenylene) by varying the side-chain ionic density from two to six per repeat units (MPS2-TMA, MPS4-TMA, and MPS6-TMA). The effect of MPS2, 4, 6-TMA as interlayers on top of a hole-extraction layer of poly(bis(4-phenyl)-2,4,6-trimethylphenylamine (PTAA) is investigated in inverted perovskite solar cells (PeSCs). Owing to the improved wettability of perovskites on hydrophobic PTAA with the CPEs, the PeSCs with CPE interlayers demonstrate a significantly enhanced device performance, with negligible device-to-device dependence relative to the reference PeSC without CPEs. By increasing the ionic density in the MPS-TMA interlayers, the wetting, interfacial defect passivation, and crystal growth of the perovskites are significantly improved without increasing the series resistance of the PeSCs. In particular, the open-circuit voltage increases from 1.06 V for the PeSC with MPS2-TMA to 1.11 V for the PeSC with MPS6-TMA. The trap densities of the PeSCs with MPS2,4,6-TMA are further analyzed using frequency-dependent capacitance measurements. Finally, a large-area (1 cm²) PeSC is successfully fabricated with MPS6-TMA, showing a power conversion efficiency of 18.38% with negligible hysteresis and a stable power output under light soaking for 60 s.     

Flower‐shaped ultra‐wideband fractal antenna

A flower‐shaped ultra‐wideband fractal antenna is presented. It comprises a fourth iterative flower‐shaped radiator, asymmetrical stub‐loaded feeding line, and coplanar quarter elliptical ground planes. A wide operating band of 12.12 GHz (4.58‐16.7 GHz) for S ₁₁ ≤ ? 10 dB is achieved along with an overall antenna footprint of 15.7 × 11.4 mm². In addition, other desirable characteristics, that is, omnidirectional radiation patterns, peak gain upto 5 dB, and fidelity factor more than 75% are achieved. A good agreement exists between the simulation and measured results. The obtained results illustrate that this antenna has wide operating range and compact dimensions than available structures.     

Impact of adhesive ingredients on adhesion between rubber and brass-plated steel wire in tire

Proficiency on underlying mechanism of rubber-metal adhesion has been increased significantly in the last few decades. Researchers have investigated the effect of various ingredients, such as hexamethoxymethyl melamine, resorcinol, cobalt stearate, and silica, on rubber-metal interface. The role of each ingredient on rubber-metal interfacial adhesion is still a subject of scrutiny. In this article, a typical belt skim compound of truck radial tire is selected and the effect of each adhesive ingredient on adhesion strength is explored. Out of these ingredients, the effect of cobalt stearate is found noteworthy. It has improved adhesion strength by 12% (without aging) and by 11% (humid-aged), respectively, over control compound. For detailed understanding of the effect of cobalt stearate on adhesion, scanning electron microscopy and energy dispersive spectroscopy are utilized to ascertain the rubber coverage and distribution of elements. X-ray photoelectron spectroscopy results helped us to understand the impact of Cu_XS layer depth on rubber-metal adhesion. The depth profile of the Cu_XS layer was found to be one of the dominant factors of rubber-metal adhesion retention. Thus, this study has made an attempt to find the impact of different adhesive ingredients on the formation of Cu_XS layer depth at rubber-metal interface and establish a correlation with adhesion strength simultaneously.     

Mathematical model for computer simulation and control of steelmaking

A dynamic model for computer simulation and control of steelmaking has been developed. It is essentially based on multicomponent mixed transport control theory with the incorporation of energy balance calculations. The model is applicable to both steelmaking in electric furnaces as well as in oxygen steelmaking converters. The adjustable parameters of the model for simulation of oxygen steelmaking are gas evolution rate (G_co). oxygen flux factor (F_o) and emulsification factor (EM). These simulation parameters, when combined with on-line measurement of off-gas composition and temperature, enable complete dynamic control of the process. The model developed is applied, as an example, to an industrially produced heat in a top blown oxygen steelmaking converter and the results of simulation are discussed.     

A new approach to study organic solar cell using Lambert W-function

Organic photovoltaic solar cells bear an important potential of development in the search for low-cost modules for the production of domestic electricity. One of the main differences between inorganic and organic solar cells is that photo-excitation in these materials does not automatically lead to the generation of free charge carriers, but to bind electron–hole pairs (exciton) with a binding energy of about 0.4 eV. Till now various numerical methods using approximations have been reported to study different aspects of organic solar cells. For the first time an accurate method using Lambert W-function is presented to study different parameters of organic solar cells.     

Non-pinched, minimum energy distillation designs

Non-pinched, minimum energy solutions are important class of distillation designs that offer the potential advantage of a better trade-off between capital investment and operating costs. In this paper, two important tasks associated with non-pinched distillation designs are studied. Thus the novel contributions of this work to the literature are

(1) A comprehensive methodology for finding non-pinched minimum energy designs.

(2) Understanding of the reasons for the existence of non-pinched distillation designs.

It is shown that the recent shortest stripping line distance approach of Lucia et al. [Lucia, A., Amale, A. and Taylor, R., 2007, Distillation pinch points and more. Comput Chem Eng, available on-line] is capable of systematically and reliably finding non-pinched, minimum energy distillation designs. In addition, we provide an understanding of the reasons behind the existence of non-pinched designs, which include trajectories that follow unstable branches of a pinch point curve in azeotropic systems, the inherent looping structure of trajectories in hydrocarbon separations, and the presence of ancillary constraints in multi-unit processes like extraction/distillation. Several distillation examples are studied and many numerical results and geometric illustrations are presented that show the shortest stripping line distance methodology is indeed a powerful and systematic tool for computing non-pinched, minimum energy designs and that support the underlying reason we provide for the existence of non-pinched designs.     

Seeking the truth about ad hoc join costs

In this paper, we re-examine the results of prior work on methods for computing ad hoc joins. We develop a detailed cost model for predicting join algorithm performance, and we use the model to develop cost formulas for the major ad hoc join methods found in the relational database literature. We show that various pieces of “common wisdom” about join algorithm performance fail to hold up when analyzed carefully, and we use our detailed cost model to derive op timal buffer allocation schemes for each of the join methods examined here. We show that optimizing their buffer allocations can lead to large performance improvements, e.g., as much as a 400% improvement in some cases. We also validate our cost model's predictions by measuring an actual implementation of each join algorithm considered. The results of this work should be directly useful to implementors of relational query optimizers and query processing systems. Edited by M. Adiba. Received May 1993 / Accepted April 1996