Fabrication of barium titanate ceramics via digital light processing 3D printing by using high refractive index monomer

A digital light processing (DLP) technology has been developed for 3D printing lead-free barium titanate (BTO) piezoelectric ceramics. By comparing the curing and rheological properties of slurries with different photosensitive monomer, a high refractive index monomer acryloyl morpholine (ACMO) was chosen, and a design and preparation method of BTO slurry with high solid content, low viscosity and high curing ability was proposed. By further selecting the printing parameters, the single-layer exposure time was reduced and the forming efficiency has been greatly improved. Sintered specimens were obtained after a nitrogen-air double-step debinding and furnace sintering process, and the BTO ceramics fabricated with 80 wt% slurry shows the highest relative density (95.32 %) and piezoelectric constant (168.1 pC/N). Furthermore, complex-structured BTO ceramics were prepared, impregnated by epoxy resin and finally assembly made into hydrophones, which has significance for the future design and manufacture of piezoelectric ceramic-based composites that used in functional devices.     

Aluminum based reflective nanolens arrays to improve the effectiveness of ultraviolet inactivation of Escherichia coli O157:H7 and Listeria monocytogenes in water and a sucrose solution

Food Science and Biotechnology - Aluminum based reflective nanolens arrays were developed via a series of aluminum electropolishing and anodization steps with subsequent selective dissolution of...     

Preparation and characterization of mullite whisker reinforced ceramics made from coal fly ash

Ceramics with mullite whiskers were prepared from coal fly ash and Al₂O₃ raw materials, with AlF₃ used as an additive. The phase structures and microstructures of the ceramics were identified via X-ray diffraction and scanning electron microscopy, respectively. The results show that pickling of coal fly ash is an effective method for enhancing the flexural strength of ceramics. Sintering temperature and AlF₃ addition were also key factors influencing the creation of ideal ceramics. The ceramic made from pickled coal fly ash, 6?wt% AlF₃, and sintered at 1200?°C, exhibited the highest flexural strength of 59.1?MPa, and had a bulk density of 1.32?g/cm³ and porosity of 26.8%. The results show that ceramic materials made under these conditions are ideal candidates for manufacturing ceramic proppants for the exploitation of unconventional oil and gas resources.     

SUBSCRIPTION 2018

正Four issues per volume a year,CHINA’S REFRACTORIES is distributed worldwide by airspeed delivery at no extra cost to subscribers.     

合成己二腈反应技术研究——(Ⅴ)己二腈工业反应过程模拟与反应器改造

对己二腈工业反应器提出了两釜串联带回流的模型,通过模拟计算得出模型的级间返混系数 f=6的结论。该模型能较好地预测工业反应器中物料组分浓度变化和气、液两相的流动特性;指出了现工业反应器的鼓泡中和段体积偏小是造成己二酸浓度偏高的关键;提出了可以通过增加串连一个鼓泡预反应段的改造方案,能有效地降低己二酸的浓度,从7%降至4%左右,从而能较好地减缓腐蚀和结焦。     

一种基于三次样条函数求离子浓度的自动算法

本文提出了一种用三次样条函数模拟双次标准加入法测量方程，直接求解离子浓度的自动算法。比较了三咱不同边界条件下用要池数计算离子浓度的结果。造出节点区间两极端点的二阶导数为零时的三次样条函数为最佳模拟函数。并讨论了该方法在实际分析中误差的来源及消除办法。经对一系列文献数据的验算对比，表明本法完全可代替传统的迭代法和查图法，且能方便地设置在智能化的电位分析系统中。     

下T6-361井多井防碰绕障技术

下T6—361井是一口双靶定向井，由于受地面和地质条件的限制，必须穿越9口井，其中最近的4口井防碰距仅为13—32m，钻井施工难度大，是一口较典型的多井防碰绕障定向井。在优化井身剖面设计、优选钻具组合、采用导向钻井技术的基础上，采取了一系列安全钻进措施，顺利钻至设计井深。对该井的地质工程设计、井眼轨迹控制及防碰绕障技术等进行了介绍，对同类型井的施工有一定的借鉴。     

掺钛蓝宝石激光晶体中夹杂物的分析

本文用大视场光学显微镜、电子探针观察和分析了掺钛蓝宝石激光晶体中夹杂物的形状、尺寸大小及元素组成，并提出消除和减少这些夹杂物的方法．     

军用滑木箱的设计分析

介绍了按日本标准设计的横板式和国内竖板式军用滑木箱的结构设计参数，从木箱抗弯、抗静压及顶盖抗弯三方面对比了两种木箱的力学性能，分析了两种木箱的特点及适用范围。     

MRF: A Framework for Source and Destination Based Bandwidth Differentiation Service

In this paper, we shall generalize the concepts of fairness, TCP-friendliness and TCP-compatibility such that more source adaptation schemes can be designed to support diverse applications over the Internet. A simple but efficient framework, in the form of a monotonic response function (MRF), is proposed for the analysis and the design of memoryless window-based source adaptation protocols by using these concepts. We first derive a necessary and sufficient condition for step-wise convergence to the weighted fairness. It is then used to construct increase-decrease policies. The requirements of our increase-decrease policy are less conservative than those of the CYRF (Choose Your Response Function) that was proposed in . Our MRF is suitable for transmission control protocol (TCP) and user datagram protocol (UDP), and can be used to design TCP-friendly and multimedia-friendly source adaptation schemes. Meanwhile, our MRF can be applied to provide bandwidth differentiation service without any change to the router of the existing Internet.