Surface Modification by a Flexible Tool. 1. Plastic Surface Deformation and Simultaneous Coating Application by Rotating Wire Brushes

The machining of metal surfaces and the application of functional coatings by means of a flexible tool (a rotating wire brush) is considered. Frictional cladding may be applied on metal-cutting machines by means of simple attachments or manual angle grinders.     

Mathematical Model of the Accelerated Cooling of Metal in Thick-Plate Hot Rolling

Metallurgist - The paper describes the issues in predicting the consumer properties of thick-plate pipe products manufactured at the hot rolling mill 5000 of the Magnitogorsk Iron and Steel Works....     

Study of the Performance of Copper Coatings Formed by Electroplating and Deformation Cladding with a Flexible Tool

The results of comparative tests of copper coatings formed by electroplating and deformation cladding with a flexible tool (DGFT) under ultimate loads that cause breakage and burrs have been presented. The number of cycles of lateral bending that cause the copper coating to peel and the sample to break, as well as coefficient of sliding friction and the wear of samples during the friction of a lubricant-free spherical indenter on the flat surface of the copper-plated steel disks with substrate hardnesses of 20, 50, and 70 HRC, have been accepted as the performance standards. During the peeling test under bending, it has been found that cladded coatings were not peeled off from the basic material, even in the case when experimental samples were broken, and the peeling of coating in the samples with galvanic coatings has been observed on half of the first bending cycle. Based on the results of the tribotechnical tests, it has been found that copper coatings formed using the above technologies contribute mainly to a reduction in the coefficient of sliding friction on friction surfaces compared to samples without coatings. However, under loads that cause burrs, galvanic coatings have smaller values of the coefficient of sliding friction compared to cladded coatings.     

机械加工法实现金属材料表面自身纳米化的研究进展

综述了机械加工法实现金属材料表面自身纳米化的研究现状,分别从制备方法、纳米化层的形成机制、纳米化层的特点和性能等方面的研究进展进行了阐述,并对表面自身纳米化技术的发展趋势进行了简单的分析.     

Collaborative Exploration and Sensemaking of Big Environmental Sound Data

Many ecologists are using acoustic monitoring to study animals and the health of ecosystems. Technological advances mean acoustic recording of nature can now be done at a relatively low cost, with minimal disturbance, and over long periods of time. Vast amounts of data are gathered yielding environmental soundscapes which requires new forms of visualization and interpretation of the data. Recently a novel visualization technique has been designed that represents soundscapes using dense visual summaries of acoustic patterns. However, little is known about how this visualization tool can be employed to make sense of soundscapes. Understanding how the technique can be best used and developed requires collaboration between interface, algorithm designers and ecologists. We empirically investigated the practices and needs of ecologists using acoustic monitoring technologies. In particular, we investigated the use of the soundscape visualization tool by teams of ecologists researching endangered species detection, species behaviour, and monitoring of ecological areas using long duration audio recordings. Our findings highlight the opportunities and challenges that ecologists face in making sense of large acoustic datasets through patterns of acoustic events. We reveal the characteristic processes for collaboratively generating situated accounts of natural places from soundscapes using visualization. We also discuss the biases inherent in the approach. Big data from nature has different characteristics from social and informational data sources that comprise much of the World Wide Web. We conclude with design implications for visual interfaces to facilitate collaborative exploration and discovery through soundscapes.     

基于GMAW堆焊成形的间隔焊道搭接量模型

焊道搭接量在较大程度上影响着基于三维熔化极气体保护焊直接成形过程的顺利进行以及成形件的精度.文中根据焊接熔滴过渡的物理特性,建立了GMAW堆焊三维成形的间隔焊道搭接量模型,在此基础上计算了平整堆焊层的相邻两道焊道的理论间隔,采用实际焊接试验对理论模型进行了验证.得到了修正的理论间隔,并计算了平整堆焊层高度;试验得到的结...     

Effect of copper doping on kinetic coefficients and their anisotropy in PbSb<Subscript>2</Subscript>Te<Subscript>4</Subscript>

In anisotropic PbSb₂Te₄ and PbSb₂Te₄:Cu single crystals, nine main independent components of the Hall, electrical-conductivity, thermopower, and Nernst-Ettingshausen effects and their anisotropy in the range 77–450 K have been studied. PbSb₂Te₄ single crystals exhibit a high hole concentration (p ≈ 3 × 10²⁰ cm⁻³). Copper exhibits a donor effect and significantly (approximately by a factor of 2) reduces the hole concentration in PbSb₂Te₄. The temperature dependences of the kinetic coefficients, except for the Hall effect, have a form typical of the one-band model. The significant anisotropy of the Hall coefficient R ₁₂₃/R ₃₂₁ ≈ 2 at low temperatures corresponds to the multi-ellipsoid model of the energy spectrum of holes in PbSb₂Te₄. An important feature of the data on transport phenomena is the high thermopower anisotropy (ΔS ≈ 60–75 μV/K) in the mixed conductivity region caused by the mixed scattering mechanism. Data on the anisotropy of the transverse Nernst-Ettingshausen effect confirm the mixed mechanism of hole scattering; in the cleavage plane, scattering at acoustic phonons dominates, while in the trigonal axis direction, impurity scattering appears significant. Doping with copper enhances the role of impurity scattering in the direction of the trigonal axis c ₃; as a result, two components of the Nernst-Ettingshausen tensor Q ₃₂₁ and Q ₁₃₂ in the PbSb₂Te₄:Cu single crystal are positive at low temperatures, whereas, in the undoped crystal, only the Q ₃₂₁ component is positive.     

Surface nanostructure formation mechanism of 45 steel induced by supersonic fine particles pombarding

By means of supersonic fine particles bombarding (SFPB),a nanostructured surface layer up to 15 μm was fabricated on a 45 steel plate with ferrite and pearlite phases. To reveal the grain refinement mechanism of SFPB-treated 45 steel,microstructure features of various sections in the treated surface were systematically characterized by X-ray diffraction (XRD),scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Grain size increases with an increase of depth from the treated surface...     

Influence of the Hydrodynamics of Electrolyte Flow on the Surface Quality in Electrochemical Machining

Russian Engineering Research - The hydrodynamics of the electrolyte in the electrode gap is considered in the electrochemical machining of an axisymmetric workpiece. The distribution of the mean...