Geopolymer assembly by emulsion templating: Emulsion stability and hardening mechanisms

This work investigates emulsion templating to synthesize hexadecane oil/geopolymer composites. In a system with hexadecane as the internal (dispersed) phase and an alkali activated continuous phase without added surfactant, adding aluminosilicate clay particles does not increase resistance against creaming or coalescence, while adding a surfactant (L35 or CTAB) stabilizes the solid-liquid interface. Infrared studies and rheological studies of the associated geopolymerization determined that the presence of the organic phase or surfactant has no significant effect on the geopolymerization kinetics, as determined by the change in time of the Si-O-T IR stretching frequency and the rheological moduli involved during the process. The stabilization of the organic template is reminiscent of Pickering emulsion even though we employ a much greater amount of inorganic material for geopolymer formation. Although the addition of surfactant has a significant effect on the behavior of the paste, the percolation of the network remains unmodified, highlighting the fact that the phenomenon is not dependent on viscosity. Finally, rheological measurements were used to obtain the mass fractal dimension of the as-made gel network, which is able to differentiate the interfacial effect between surfactant molecules with a slightly denser interphase when a cationic surfactant is used.     

Making polyurethane foams from microemulsions

A remarkable correlation exists between the degree of expansion of polyurethane foams and the structure of the reacting premixes. Polyurethane foams obtained from reacting premixes containing microemulsions are highly expanded. The expansion rate is proportional to the volume fraction of microemulsion in the premix. The stability of premixes with and without microemulsion is completely different suggesting distinct creaming mechanisms. We apply this idea to synthesize polyurethane foams from microemulsions successfully. This approach can be used to rationalize the design of polyurethane formulations leading to highly expanded foams.     

Jitter in ATM networks and its impact on peak rate enforcement

Cells arriving to an ATM network experience random delays due to queueing in upstream multiplexing stages, notably in customer premises. This is the phenomenon of jitter and the aim of the present paper is to study its influence on peak rate enforcement. We first introduce some general characterizations of jitter and then, describe two models of jittered flows based on simple queueing systems. We discuss the objectives of peak rate enforcement and study the impact of jitter on the dimensioning of jumping window and leaky bucket mechanisms. A useful synthetic characterization of jitter appears to be a remote quantile of the cell delay distribution expressed in units of the initial inter-cell interval.     

Shear mode coupling and tilted grain growth of A1N thin films in BAW resonators.

Polycrystalline A1N thin films were deposited by RF reactive magnetron sputtering on Pt(111)/Ti electrode films. The substrates were tilted by an angle ranging from 40 degrees to 70 degrees with respect to the target normal. A low deposition temperature and a high sputter gas pressure were found ideal for tilted growth. The resulting grain tilt angle amounts to about half the substrate tilt angle. For coupling evaluation, 5 GHz solidly mounted resonator structures have been realized. The tilted grain A1N films exhibited a permittivity in the 9.5-10.5 range and loss tangent of 0.3%. Two shear modes as well as the longitudinal mode could be clearly identified. The coupling coefficient k2(eff) of the fundamental thickness shear mode (TS0) was found to be about 0.5%, which is compatible with a c-axis tilt of about 6 degrees.     

Fabrication of a biocompatible flexible electroosmosis micropump

In in-vivo microsystems, one of the components is a biocompatible micropump in order to produce the necessary force to deliver the fluid from the inlet to the outlet. In this contribution, a flexible micropump is fabricated which is aimed to be suitable in drug delivery applications. It provides high degree of biocompatibility, since the only employed materials are implantation grade polydimethylsiloxane elastomer and gold for the electrical interconnects. The working principle of the micropump is based on transverse DC electroosmosis which is a new variant of conventionally applied high voltage DC electroosmosis. This new technique is based on topography irregularities introduced in the channel resulting in a non-uniform charge distribution. The advantage is to drive the micropump using a relatively low DC voltage of 10 V while getting an effective flow speed of 60 μm/s. In order to characterize the flow speed, dyed 3 μm beads are dispersed in the working fluid and their speed is measured by the line scanning technique using a confocal microscope. It is also observed that the flow has a helical profile which is an attractive feature for an efficient micro-mixer in active microfluidics and μ-TAS applications.     

Simple and low-cost fabrication of PDMS microfluidic round channels by surface-wetting parameters optimization

Convenient for both biologists and MEMS designers, Polydimethylsiloxane (PDMS) polymer is intensively investigated for its biocompatibility, transparency, high resistance under plasma treatment, flexibility and resistance to high temperature. However, for microfluidic applications, the fabrication of PDMS circular channels is difficult to achieve except by wire moulding. In this article, we present a simple, fast and low-cost fabrication method which can be applied out of clean-room environment. It is based on the deposition of alginic acid sodium salt aqueous solution, enabling the formation of a liquid cylinder on the most hydrophilic part of a hydrophilic/hydrophobic patterned surface. We experimentally studied the interaction between liquid rivulets and surfaces presenting a contrast of wettability and/or a stepwise texture. Subsequent moulding of the half-cylinder of liquid produces round PDMS microfluidic channels. The optimal parameters for hydrophilic/hydrophobic patterns have then been applied to produce the roundest possible channels. The realisation of both straight channels 300–500 μm wide, 1 cm long and 75° tangent chord angle at best, and Y-shaped channels with the same dimensions and 55° TCA is demonstrated.     

P2Y11 Agonism Prevents Hypoxia/Reoxygenation- and Angiotensin II-Induced Vascular Dysfunction and Intimal Hyperplasia Development

Vascular dysfunction in cardiovascular diseases includes vasomotor response impairments, endothelial cells (ECs) activation, and smooth muscle cells (SMCs) proliferation and migration to the intima. This results in intimal hyperplasia and vessel failure. We previously reported that activation of the P2Y11 receptor (P2Y11R) in human dendritic cells, cardiofibroblasts and cardiomyocytes was protective against hypoxia/reoxygenation (HR) lesions. In this study, we investigated the role of P2Y11R signaling in vascular dysfunction. P2Y11R activity was modulated using its pharmacological agonist NF546 and antagonist NF340. Rat aortic rings were exposed to angiotensin II (AngII) and evaluated for their vasomotor response. The P2Y11R agonist NF546 reduced AngII-induced vascular dysfunction by promoting EC-dependent vasorelaxation, through an increased nitric oxide (NO) bioavailability and reduced AngII-induced H₂O₂ release; these effects were prevented by the use of the P2Y11R antagonist NF340. Human vascular SMCs and ECs were subjected to AngII or H/R simulation in vitro. P2Y11R agonist modulated vasoactive factors in human ECs, that is, endothelial nitric oxide synthase (eNOS) and endothelin-1, reduced SMC proliferation and prevented the switch towards a synthetic phenotype. H/R and AngII increased ECs secretome-induced SMC proliferation, an effect prevented by P2Y11R activation. Thus, our data suggest that P2Y11R activation may protect blood vessels from HR-/AngII-induced injury and reduce vascular dysfunctions. These results open the way for new vasculoprotective interventions.     

UTILIZATION OF POPULATION BALANCES IN SIMULATION OF LIQUID-LIQUID SYSTEMS IN MIXED TANKS

A simulation model has been developed to model drop populations in a mixed tank. A multiblock mixed tank model has been used with the drop population balance equations developed in the literature. The drop breakage and coalescence functions used in the population balance model take into account the local turbulent energy dissipation values. The drop breakage and coalescence function parameters are fitted against drop size measurements from dense liquid-liquid dispersions, which were assumed fully turbulent. Since the local turbulence and flow values of a mixed tank are used in the present model, the fundamental breakage and coalescence phenomena can be taken into closer examination. Furthermore, the present model is capable of predicting inhomogeneities occurring in a mixed tank. It is also considered as an improved tool for process scale-up, compared to the simple vessel-averaged population balance approach, or use of correlations of dimensionless numbers only. The present model can use two sources of data for fitting parameters in the drop rate functions. One is the transient data of the measured drop size distribution as the impeller speed is changed. The other is the time-averaged data measured at different locations of the mixed tank. Different flow regions can be chosen from direct measurements or from the CFD simulations in a straightforward manner. CFD flow simulation results can be used when no experimentally obtained flow conditions are available. This is especially useful for nonstandard vessels, such as reactors containing cooling coils.     

Surfascan 3D — An industrial 3D surface texture characterisation instrument

2D profile analysis has often in the past been considered sufficient to control the geometrical features of a surface and to ensure that they are compatible with the required functionalities. Yet, experience shows that 3D surface texture analysis is now essential wherever a complete assessment of the surface is required to enable the selection of the most appropriate surface texture to achieve a required functionality.This paper introduces measurement strategies and features considered as essential by SOMICRONIC when designing or developing 3D surface texture measuring instruments, knowing that the pursued aim is to assess the measured surface in a way to reveal the real surface. This is achieved without losing sight of existing ISO standardized concepts concerning surface texture profile analysis.Indeed, essentially for economical reasons, we consider that 31) surface texture stylus instruments must be designed to achieve classical surface texture profiles measurements and characterisations and to fulfil conditions and characteristics listed and described in existing surface texture ISO standards.We propose to develop in the next paragraphs, the following points:

• - Design of the data acquisition unit of a 3D surface texture instrument

• - Strategy for the measurement of the surface

• - Application of these concepts - Examples.