Investigation on the cutting quality characteristics of abrasive water jet machining of AA6061-B4C-hBN hybrid metal matrix composites

Aluminum metal matrix composites (AMMCs) explicitly show better physical and mechanical properties as compared to aluminum alloys and results in a more preferred material for a wide range of applications. The addition of reinforcements embargo AMMCs employment to industry requirements by increasing order of machining complexity. However, it can be machined with a high order of surface integrity by nonconventional approaches like abrasive water jet machining. Hybrid aluminum alloy composites were reinforced by B₄C (5–15?vol%) and solid lubricant hBN (15?vol%) particles and fabricated using a liquid metallurgy route. This research article deals with the experimental investigation on the effect of process parameters such as mesh size, abrasive flow rate, water pressure and work traverse speed of abrasive water jet machining on hybrid AA6061-B₄C-hBN composites. Water jet pressure and traverse speed have been proved to be the most significant parameters which influenced the responses like kerf taper angle and surface roughness. Increase in reinforcement particles affects both the kerf taper angle and surface roughness. SEM images of the machined surface show that cutting wear mechanism was largely operating in material removal.     

Investigation on the tribocorrosion and electrochemical corrosion behaviour of AA2014/Al2O3 nanocomposites fabricated through ultrasonication coupled stir-squeeze casting method

Journal of Applied Electrochemistry - In this work, the tribocorrosion and electrochemical corrosion behaviour of AA2014/Al2O3 (1–4 wt%) nanocomposites were investigated. An...     

Electrolytic concentration effect on the abrasive assisted-electrochemical machining of an aluminum–boron carbide composite

All engineering materials can be machined by one or combination of processes in such a way that the material’s potential is fully exploited. Electrochemical machining is found to be a most promising process that produces various components from the hard-to-machine materials for the various applications. Electrolyte concentration is playing a positive role by improving the electrolyte conductivity, but negatively forming the passivation layer on the cut surfaces. In order to improve the surface finish and removal of generated residual materials from the cut surfaces, abrasive particles were fed along with electrolyte into the machining zone. This present paper investigates the sodium chloride (NaCl) electrolyte with varied concentration (10–30%) in association with SiC abrasive particles on the material removal rate, surface roughness, and radial overcut while machining of aluminum 6061–boron carbide (5–15?wt%) composites. This study conclusively derived that electrolyte concentration up to 20% exhibited a positive role in the material removal rate for the machining of composites because the rate of dissolution was of higher magnitude. Externally supplied abrasive particles along with electrolyte reduced the surface roughness and radial over cut to an extent. Conversely, at higher electrolyte concentration, the externally supplied abrasive particles have a little effect on the removal of the formed passivation layer as confirmed by SEM analysis.     

Comparison of plastic strains on AA5052 by single point incremental forming process using digital image processing

In this study, a surface based strain measurement was used to determine the formability of the sheet metal. A strain measurement may employ manual calculation of plastic strains based on the reference circle and the deformed circle. The manual calculation method has a greater margin of error in the practical applications. In this paper, an attempt has been made to compare the formability by implementing three different theoretical approaches: Namely conventional method, least square method and digital based strain measurements. As the sheet metal was formed by a single point incremental process the etched circles get deformed into elliptical shapes approximately, image acquisition has been done before and after forming. The plastic strains of the deformed circle grids are calculated based on the nondeformed reference. The coordinates of the deformed circles are measured by various image processing steps. Finally the strains obtained from the deformed circle are used to plot the forming limit diagram. To evaluate the accuracy of the system, the conventional, least square and digital based method of prediction of the forming limit diagram was compared. Conventional method and least square method have marginal error when compared with digital based processing method. Measurement of strain based on image processing agrees well and can be used to improve the accuracy and to reduce the measurement error in prediction of forming limit diagram.