Effects of various post-treatments on carbon nanotube films for reliable field emission

In this report, the FE characteristics of carbon nanotubes (CNTs) treated using both thermal annealing and mechanical coatings on the as-grown CNTs systematically studied. It was found that in the high temperature annealed samples, CNTs were attacked at its root during annealing due to a small amount of oxygen, and were pulled out of the substrate in places after FE measurements because of the contact resistance. However, for the mechanically coated samples both with spin on glass (SOG) and polymethyl methacrylate (PMMA), CNTs were found to be nearly intact after FE measurements and showed reliable FE characteristics over repeatable voltage scan. The reliability of CNTs during FE could be owing to the strong adhesion of CNTs to the substrate both by SOG and PMMA coatings.     

Preparation of core–shell type nanoparticles of diblock copolymers of poly(L‐lactide)/poly(ethylene glycol) and their characterization in vitro

Core–shell type nanoparticles of poly(L ‐lactide)/poly(ethylene glycol) (LE) diblock copolymer were prepared by a dialysis technique. Their size was confirmed as 40–70 nm using photon correlation spectroscopy. The ¹H‐NMR analysis confirmed the formation of core–shell type nanoparticles and drug loading. The particle size, drug loading, and drug release rate of the LE nanoparticles were slightly changed by the initial solvents that were used. The drug release behavior of LE core–shell type nanoparticles showed an initial burst during the first 12 h and then a sustained release until 100 h. The degradation behavior of LE block copolymer nanoparticles was divided into three phases: the initial rapid degradation phase, the stationary phase, and the rapid degradation phase until complete degradation. It was suggested that lidocaine release kinetics were predominantly governed by the diffusion mechanism in the initial burst phase and after that by both of the diffusion and degradation mechanisms. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2625–2634, 2002     

Polyaniline-multiwalled carbon nanotube composites: Characterization by WAXS and TGA

Polyaniline/carboxylated multi-walled carbon nanotube (PAni/c-MWNT) nanocomposites have been synthesized by micellar aided emulsion polymerization with various c-MWNTs compositions, viz., 0.5, 1, 5, and 10 wt %. The microcrystalline parameters such as the nanocrystal size (〈N〉), lattice strain (g), interplanar distance (d_hkl), width of the crystallite size distribution, surface weighted crystal size (D_s), and volume of the ordered regions were calculated from the X-ray data by using two mathematical models, namely the Exponential distribution and Reinhold distribution methods. The effects of heat ageing on the microcrystalline parameters of the PAni/c-MWNT nanocomposites were also studied and the results are correlated. The thermal stability and electrical resistivity of the PAni/c-MWNT nanocomposites were examined with thermogravimetric analysis (TGA) and a conventional two-probe method. The TGA data indicate that the thermal stability of the nanocomposites improved after the incorporation of c-MWNTs. The influence of temperature on the resistivity of the nanocomposites was also measured. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

KWTA networks and their applications

Winner-Take-All (WTA) or K-Winner-Take-All (KWTA) networks have been frequently used as the basic building blocks of complex neural networks. This paper introduces a new selection rule for network connections that implements stable KWTA networks. To widen the applications of WTA networks, a new class of WTA networks is proposed, and their efficient design methods are presented. We demonstrate the properties of the generalized class of WTA networks, through three application examples.     

Kinetics of volume expansion during infusion of Ringer’s solution based on two volume model

In this work mathematical models were developed to represent the kinetics of volume changes of fluid spaces associated with infusion of Ringer’s solution. During infusion of Ringer’s solution, the human body is assumed to be characterized by the two-fluid space model which has second volume space in addition to the first volume so that fluid exchanges between these two spaces are possible. Various infusion types were tested to accommodate different medical situations. Volunteers were given Ringer’s solution and the changes in blood hemoglobin were detected. From the comparison with experimental data, the two-fluid space model was found to represent adequately the kinetics of human volume expansion during infusion of Ringer’s solution.     

A water‐developable negative photoresist based on the photocrosslinking of N‐phenylamide groups with reduced environmental impact

A water‐developable negative photoresist based on the photocrosslinking of N‐phenylamide groups was prepared by the copolymerization of 4‐styrenesulfonic acid sodium salts (SSS) with N‐phenylmethacrylamide (copolymer A) or p‐hydroxy‐N‐phenylmethacrylamide (copolymer B), and its properties such as solubility changes, photochemical reaction, and photoresist characteristics were studied. The copolymer containing a relatively higher amount of SSS units was soluble in water. Solubility changes of the copolymers in the various buffer solutions of pH 4 ～ 11 and in water upon irradiation were observed by the measurement of insoluble fraction. The copolymers were soluble in water before irradiation, whereas they became insoluble upon irradiation with the UV light of 254 nm. The photochemical reaction of the copolymer studied by the UV and IR absorption spectroscopies indicated that a photo‐Fries rearrangement was favored for copolymer A, whereas a photocrosslinking reaction was predominate for copolymer B. Resist properties of the copolymers were studied by measurement of the normalized thickness and by development of the micropattern. Negative tone images with a resolution of 1 μm were obtained with these materials that have a sensitivity (D) of ～ 1100 mJ/cm² with an aqueous developing process.© 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1172–1180, 2002     

Characteristics of polyvinylpyrrolidone-layered silicate nanocomposites prepared by attrition ball milling

Polyvinylpyrrolidone (PVP)/sodium montmorillonite (MMT) nanocomposites prepared via the solution intercalation method were investigated by UV/vis, SEM, X-ray diffraction, TEM, FT-IR and PLM (polarized light microscopy). PVP/MMT nanocomposites show exfoliation below 20 wt% MMT and intercalation above this concentration. Nanocomposites retain good optical clarity and increased thermal resistance with MMT content. The compatibility between PVP and MMT and their enhanced properties may be explained by hydrogen bonding interactions. In addition, the nanocomposites prepared under more rigorous mixing conditions show better transparency because the smaller particle sizes are induced. In addition, the study on optically clear PVP/MMT suspensions helps one to understand how optical anisotropy of MMT is affected by the existence of polymer in aqueous solution.     

Fabrication of a gradient refractive index preform using laminar shear mixing

A gradient refractive index rod was successfully prepared by a new fabrication method using laminar shear mixing, and a graded index polymer optical fiber that satisfied IEEE1394b was obtained from the method. To fabricate the gradient refractive index rod, a liquid monomer mixture with a relatively low refractive index was placed in a prepared cylindrical glass reactor and a transparent polymer rod with a higher refractive index was introduced at the center of the reactor. The reactor and the polymer rod were then rotated concurrently with a small rotating speed difference to generate a Couette flow in the liquid phase. The centrifugal force generated by rotation and the polymer diffusion into the liquid monomer mixture developed a graded concentration profile in a radial direction. The Couette flow could reduce the concentration fluctuation in a tangential direction. In addition, the graded index profile could be controlled by the copolymer composition of the rod and its diameter. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1100–1104, 2005     

Modeling and economic analysis of CO<Subscript>2</Subscript> separation process with hollow fiber membrane modules

The main purpose of the study was to develop a model using ASPEN and Excel simulation method to establish optimum CO₂ separation process utilizing hollow fiber membrane modules to treat exhaust gas from LNG combustion. During the simulation, optimum conditions of each CO₂ separation scenario were determined while operating parameters of CO₂ separation process were varied. The characteristics of hollow fibers membrane were assigned as 60 GPU of permeability and 25 of selectivity for the simulation. The simulation results illustrated that 4 stage connection of membrane module is required in order to achieve over 99% of CO₂ purity and 90% of recovery rate. The resulted optimum design and operation parameters throughout the simulation were also correlated with the experimental data from the actual CO₂ separation facility which has a capacity of 1,000 Nm³/day located in the Korea Research Institute of Chemical Technology. Throughout the simulation, the operating parameters of minimum energy consumption were evaluated. Economic analysis of pilot scale of CO₂ separation plant was done with the comparison of energy cost of CO₂ recovery and equipment cost of the plant based on the simulation model. This work was presented at the 6 ^th Korea-China Workshop on Clean Energy Technology held at Busan, Korea, July 4–7, 2006.