The Influence Analysis that a Phase Characteristic of the High‐Level Earthquake Gives to Vibration Response Characteristic of the 550‐kV Disconnectors

We developed the 550‐kV disconnectors that strengthened earthquake proofing by the addition of the damper unit and weight reduction of conductive part based on the damage of the 550‐kV disconnectors by the Great East Japan earthquake (March 11, 2011) and inspected the earthquake proofing performance by shake table test. In shake table test, we performed the test by the artificial seismic wave that varied in phase characteristic in addition to the test by resonance method. And, in a high‐level earthquake area, we analyzed it about the influence that a phase characteristic of the artificial seismic wave gave to stress to occur in disconnectors. As a result, it is thought that the stress to occur in disconnectors is decided by a primary natural frequency basically because a bending strain to occur to the disconnectors in the time when the resonance frequency ingredient becomes the big acceleration response value grows big. But, on a particular phase condition, it was confirmed that the bending strain to occur in disconnectors might grow big conspicuously. As for this, the possibility is thought about by influence of higher natural frequency doing superposition.     

The isothermal conductivity improvement in zirconia-based ceramics under 24 GHz microwave heating

Abstract Under 24-GHz millimetre-wave irradiation heating ionic conductivity of zirconia base ceramics was up to 20 times higher than that of a conventionally-heated sample at the same temperature of 400 °C. The degree of enhancement could be altered by changing the stabilising atom from Y to Yb. Enhancement of ionic conduction was prominent in the setup condition of larger self-heating ratio and larger MMW absorbing materials. The isothermal improvement of ionic conductivity under MMW irradiation would be ascribed to the non-thermal effect.     

Circulating Organ-Specific MicroRNAs Serve as Biomarkers in Organ-Specific Diseases: Implications for Organ Allo- and Xeno-Transplantation

Different cell types possess different miRNA expression profiles, and cell/tissue/organ-specific miRNAs (or profiles) indicate different diseases. Circulating miRNA is either actively secreted by living cells or passively released during cell death. Circulating cell/tissue/organ-specific miRNA may serve as a non-invasive biomarker for allo- or xeno-transplantation to monitor organ survival and immune rejection. In this review, we summarize the proof of concept that circulating organ-specific miRNAs serve as non-invasive biomarkers for a wide spectrum of clinical organ-specific manifestations such as liver-related disease, heart-related disease, kidney-related disease, and lung-related disease. Furthermore, we summarize how circulating organ-specific miRNAs may have advantages over conventional methods for monitoring immune rejection in organ transplantation. Finally, we discuss the implications and challenges of applying miRNA to monitor organ survival and immune rejection in allo- or xeno-transplantation.     

Si-C-O glass-like compound/exfoliated graphite composites for negative electrode of lithium ion battery

Two low molecular weight silicone compounds, a cyclic type having vinyl groups and a chain-type having Si-H bonds, a catalyst for curing, and a catalyst regulator were mixed. The mixture was impregnated into exfoliated graphite (EG) by sorption, and cured in air at 200 °C. By this process cross-linked silicone coatings were formed on graphite flakes. The composites of Si-C-O glass-like compounds and EG were synthesized by heat treatment of this precursor at 1000-1400 °C for 1 h in argon. The composites formed at 1000-1300 °C were amorphous by XRD and had practically the same chemical composition: Si 44-45, C 27-29, O 25-26, H < 0.5, all in mass%. The ²⁹Si MAS-NMR spectra indicated that the compound formed at 1000 °C was mainly composed of siloxane bonds and amorphous silica, whereas in the compound formed at 1300°C, Si-C bonds and amorphous silica were predominant. The insertion/extraction characteristics of lithium ions for the electrode prepared with composite:poly(vinylidene fluoride) = 90:10 mass% were examined in 1 mol L⁻¹ LiClO₄ solution of ethylene carbonate:diethyl carbonate = 50:50 vol%. High, 650-700 mA h g⁻¹, capacities and steady cycle performance at 50 mA g⁻¹ were achieved with the composites formed at 1250-1300 °C. Capacities of the composites formed at 1200 °C and lower were initially higher but decreased with increasing number of cycles. The composites formed at 1350 °C showed good cycle performance but the capacity was about 500 mA h g⁻¹ due to the formation of β-SiC. Except for the first cycle, the capacity-potential characteristics were similar to those of hard carbons and the coulomb efficiency was 95-100%. For all the composites the capacity was larger than that of graphite (372 mA h g⁻¹) in the range of 50-200 mA g⁻¹. Due to the large insertion capacity of the first cycle, the efficiency was low (60-70%) at first. By short-circuiting the working electrode to the lithium foil counter electrode for a certain period, the irreversible capacity of the first cycle was almost eliminated. It indicates that direct doping of lithium ions into composites is a promising way to increase the efficiency of the first cycle.     

Mechano-electrochemistry of a passive surface using an in situ micro-indentation test

Depassivation–repassivation of iron surfaces in boric–borate solutions were investigated by using the micro-indentation test. A pair of current peaks due to repair of the passive film following rupture of the film were observed during a series of indenter drives, i.e., loading and unloading of the indenter. The shape of the current peak depended on environmental conditions (conductivity and pH of the solution) and substrate conditions (mechanical processing history, alloyed element) as well as indentation conditions (repetition, maximum depth, and maximum load). Plastic deformation of the surface was accompanied by surface depassivation, while no depassivation occurred during the elastic deformation, indicating that the passive film on iron has a ductile property. The solution conditions did not affect the scale of depassivation but affected the rate of repassivation. Dislocations in the substrate made surface depassivation difficult but enhanced reactivity during the repassivation. The test also revealed that type-312L stainless steel has high corrosion resistance in a concentrated NaCl solution.     

Simple evaluation of aortic arch calcification by chest radiography in hemodialysis patients

Vascular calcification is associated with a poor prognosis in dialysis patients. It can be assessed with computed tomography but simple inoffice techniques may provide useful information. We compared the results obtained with a simple noninvasive technique with those obtained using multidetector computed tomography for aortic arch calcification volume (AoACV) in chronic hemodialysis (HD) patients. The enrolled study subjects were 63 (32 men and 31 women) maintenance HD patients. Calcification of the aortic arch was semiquantitatively estimated with a AoAC score (AoACS) on plain chest radiology. The AoACV was increased, with a mean value of 6.6 ranging from 0% to 36.5%. The coefficient of intraobserver variation was less than 2.5%. Aortic arch calcification score was highly correlated with AoACV (r=0.635, P<0.001). Multiple regression analysis showed age (F value=12.62, P<0.001) and pulse pressure (F value=4.54, P=0.037) to be significant independent determinants of AoACS. In conclusion, a simple measurement of AoACS may be useful for inoffice imaging to choose a therapeutic regimen in HD patients.     

Germanium recovery using polyphenol microspheres prepared by horseradish peroxidase reaction

BACKGROUND: The formation of polyphenol microspheres by the polymerization of 3‐methylcatechol was performed in a methanol/phosphate buffer solution using horseradish peroxidase (HRP), without the use of a surfactant or a water/oil interface, to be used for germanium recovery. RESULTS: The polyphenol microspheres were of diameter 1 mm. The functional group density of phenol group in the polymer was approximately 15 mol kg^?1 determined by the Folin‐Denis method. In batchwise experiments, the amount of germanium adsorbed was 0.23 mol kg^?1. CONCLUSION: Because germanium is a rare metal, a system for its recovery is required. Using the proposed system, continuous recovery of germanium can be achieved using multilayered microspheres. Copyright © 2011 Society of Chemical Industry