Optimal Water Allocation of Surface and Ground Water Resources Under Climate Change with WEAP and IWOA Modeling

Water Resources Management - The water evaluation and planning (WEAP) approach and the invasive weed optimization algorithm (IWOA) are herein employed to determine the optimal operating policies in...     

Microwave heating controlled reactive melt infiltration for graphite-Si-SiC ceramics manufacturing

In this work, we investigated a procedure which exploits microwave ovens to produce SiC- based components by reactive melt infiltration of silicon into graphite preforms. The employed oven is designed to grant optical access to the sample surface, which allows to measure its temperature evolution though a noncontact pyrometer. This signal was used as a feedback to control the power provided to the preform and as an experimental output whose analysis provides insight into the reaction mechanism. Specifically, it is found that complete infiltration is achieved much before the end of the reaction. The latter is not fully self-sustained as the global reaction rate continuously decreases with time until it is no more able to keep the temperature above the silicon solidification value. At that point, the reaction stops. The analysis of the processed samples proved that this procedure allows producing fully infiltrated samples without material failure by adjusting the heat provided during the infiltration stage rather than by tuning the preform structure and composition, which is the usual approach. The proposed method is less time and energy consuming than the standard one.     

Long-term transients in a reactor under forced concentration cycling

In the approach to a cycle-invariant state in the forced feed concentration cycling of the CO oxidation over a NiO catalyst, a very long transient has been observed lasting 80 ks or more. This transient appears to be associated only with CO pretreatment of the catalyst and is not a general phenomenon. The slow convergence to the cycle-invariant state reported in certain modelling calculations in the literature appears to have a different cause.     

Trends in Hydrological Parameters of a Southern Brazilian Watershed and its Relation to Human Induced Changes

The Piracicaba river basin is a subtropical watershed located in the southeastern region of Brazil. With an area of 12 400 km², the basin is a typical example of new landscape resulting from development in tropical and sub-tropical regions: establishment of intensive industrial and agricultural processes were followed by significant population growth and water management. This scenario has led to significant increase in water demand and decrease in water quality. The main objective of this study is the detection of changes in the patterns of flow and precipitation in the basin, and its possible relation to man-induced changes. Statistical analyses were performed on records of precipitation, evapotranspiration and streamflow, from 1947 to 1991. Precipitation and evapotranspiration totals showed significant increasing trends for the entire basin. From eight streamflow gauge stations, half showed significant decreasing trend. The most probable cause of such trends is the export of water from the basin to the metropolitan region of São Paulo city.     

Kinetic model for water/oil absorption of mesquite gum (Prosopis juliflora) and gum arabic (Acacia senegal)

The water and oil uptake of mesquite and arabic gums in powdered form was studied at temperatures of 23, 35 and 45°C. A previously proposed equation to predict osmotic equilibrium was tested using the experimental data with both gums and a good statistical fit was obtained. Mesquite gum showed the highest water and oil absorption at all temperatures studied. Temperature dependence of the reciprocal of the S₁ and WL_∞ were determined using an Arrhenius equation. The activation energy for water and oil absorption for gum arabic was 21.98 and 39.57 kJ mol⁻¹, compared to that of mesquite gum having values of 15.79 and 46.16 kJ mol⁻¹, respectively. A second order kinetic model was obtained for water and oil absorption for both gums.     

Detection of failure sites by focused ion beam and nano-probing in the interconnect of three-dimensional stacked circuit structures

Focused ion beam (FIB) and nano-probing were applied for failure analysis of three-dimensional stacked circuits with copper through-silicon-vias between the stacked chips. The failure analysis was done after high temperature storage and thermal cycling tests. Passive voltage contrast in FIB allowed to pinpoint the open sites. FIB cross-sections showed the presence of opens at the bottom of the copper vias. The failure cause was suspected to be an interlayer particle, which was confirmed by optical profilometry. Nano-probing was used on another sample to pinpoint the failure location through the measurement of the local resistance within the daisy chains. The failure was traced out to be related with surface contamination.     

Microstructural and textural characterization of a hot-rolled IF steel

The present paper reports the experimental results on the microstructural and textural characterization of a hot-rolled IF steel. The IF steel was hot-rolled in multiple passes in the austenitic field (1,070 °C) followed by air-cooling. SEM, TEM, and LOM were used to image the microstructure of the material. The global texture was determined by X-ray diffraction (XRD) technique. The mesotexture of selected regions was investigated by electron backscatter diffraction (EBSD). Results show the presence of a diffuse (nearly random) and weak texture in the hot-band that consists of recrystallized polygonal grains and subgrains. The fraction of boundaries with misorientations comprised in the interval 2° ≤ ψ < 15° was found to be lower than 5%. It can be concluded that these low angle boundaries and the presence of subgrains can be associated to the existence of a few areas softened by recovery during or after hot rolling in austenitic field.