可控震源施工中电台数据传输不良的原因分析及排除

可控震源在施工中,常常出现各种电台干扰,导致震源数据传输不正常或震源收不到仪器发出的遥控启动信号,影响正常施工.本文介绍了各种电台干扰引起的故障现象,分析了故障产生的原因,给出了故障的排除方法.     

Rearrangeable nonblocking SOI waveguide thermooptic 4/spl times/4 switch matrix with low insertion loss and fast response

A rearrangeable nonblocking 4/spl times/4 thermooptic silicon-on-insulator waveguide switch matrix at 1.55-/spl mu/m integrated spot size converters is designed and fabricated for the first time. The insertion losses and polarization-dependent losses of the four channels are less than 10 and 0.8 dB, respectively. The extinction ratios are larger than 20 dB. The response times are 4.6 /spl mu/s for rising edge and 1.9 /spl mu/s for falling edge.     

陶粒混凝土复合保温板的生产及应用

本文结合国内外生产实践，介绍了陶粒混凝土复合保温板的构造、基本配方、物理力学性能、生产方法与工艺流程以及应用情况。     

Analysis and Simulation of S-shaped Waveguide in Silicon-on-insulator

The simulation and analysis of S-shaped waveguide bend are presented.Bend radius larger than 30 mm assures less than 0.5 dB radiation loss for a 4-μm-wide silicon-on-insulator waveguide bend with 2-μm etch depth.Intersection angle greater than 20° provides negligible crosstalk (<-30 dB) and very low insertion loss.Any reduction in bend radius and intersection angle is at the cost of the degradation of characteristics of bent waveguide and intersecting waveguide, respectively.     

硅表面上的纳米量子点的自组织生长

纳米半导体量子点以其所具有的新颖光电性质与输运特性正在受到人们普遍重视。作为制备高质量纳米量子点的工艺技术 ,自组织生长方法倍受材料物理学家的青睐。而如何制备尺寸大小与密度分布可控的纳米量子点更为人们所注目。因为这是关系到纳米量子点最终能否器件实用化的关键。文中以此为主线 ,着重介绍了各种 Si表面 ,如常规表面、氧化表面、台阶表面以及吸附表面上 ,不同纳米量子点的自组织生长及其形成机理 ,并展望了其未来发展前景     

剑江化肥厂销盐蒸发系统的改造

本文对硝盐蒸发系统的工艺改造作了系统阐述，并分析了改造后所取得的经济效益。     

KINETICS OF HYDROCARBON GAS GENERATION FROM MARINE KEROGEN AND OIL: IMPLICATIONS FOR THE ORIGIN OF NATURAL GASES IN THE HETIANHE GASFIELD, TARIM BASIN, NW CHINA

In this paper we derive kinetic parameters for the generation of gaseous hydrocarbons (C_1‐5) and methane (C₁) from closed‐system laboratory pyrolysis of selected samples of marine kerogen and oil from the SW Tarim Basin. The activation energy distributions for the generation of both C_1‐5 (Ea = 59‐72kcal, A = 1.0×10¹⁴ s^?1) and C₁ (Ea = 61‐78kcal, A = 6.06×10¹⁴ s^?1) hydrocarbons from the marine oil are narrower than those for the generation of these hydrocarbons from marine kerogen (Ea = 50‐74kcal, A = 1.0×10¹⁴ s^?1 for C_1‐5; and Ea = 48‐72kcal, A=3.9×10¹³ s^?1 for C₁, respectively). Using these kinetic parameters, both the yields and timings of C_1‐5 and C₁ hydrocarbons generated from Cambrian source rocks and from in‐reservoir cracking of oil in Ordovician strata were predicted for selected wells along a north‐south profile in the SW of the basin. Thermodynamic conditions for the cracking of oil and kerogen were modelled within the context of the geological framework. It is suggested that marine kerogen began to crack at temperatures of around 120°C (or 0.8 %Ro) and entered the gas window at 138°C (or 1.05 %Ro); whereas the marine oil began to crack at about 140 °C (or 1.1 %Ro) and entered the gas window at 158 °C (or 1.6%Ro). The main geological controls identified for gas accumulations in the Bachu Arch (Southwest Depression, SW Tarim Basin) include the remaining gas potential following Caledonian uplift; oil trapping and preservation in basal Ordovician strata; the extent of breaching of Ordovician reservoirs; and whether reservoir burial depths are sufficiently deep for oil cracking to have occurred. In the Maigaiti Slope and Southwest Depression, the timing of gas generation was later than that in the Bachu Arch, with much higher yields and generation rates, and hence better prospects for gas exploration. It appears from the gas generation kinetics that the primary source for the gases in the Hetianhe gasfield was the Southwest Depression.     

动基座自校零压电陀螺

研制的一种压电陀螺能在动基座条件下自动消除由于温度和时间变化造成的零位漂移。典型的产品可使零位变化小于０．０５°／ｓ。零位的温度系数小于０．０００５°／ｓ／℃。     

新一代银行大型机网络接入技术研究

银行大型机网络接入技术的转型是当前一个非常重要的研究与应用课题。文章在成功实现银行大型机网络接入技术转型的基础上,分析了相关新技术,解决了转型中的关键问题,提出并实现了一种稳定高效的银行大型机网络接入技术方案,对银行大型机网络接入技术的转型具有指导意义,对银行信息化技术研究具有重要参考价值。     

破片式战斗部优化设计技术研究

侧重研究了破片式战斗部装药外形的优化设计技术。提出了装药外形与破片飞散特性（如破片飞散角，分布带宽等）之间的数学描述；建立了圆弧和对数螺线装药外形母线与战斗部其他设计参数间的数学模型。在假定约束条件下，优化设计了破片了聚焦式战斗部的结构参数；静爆试验结果表明，破片分布与理论计算吻合较好。