An investigation of the drivers,barriers, and incentives for environmental management systems in the Malaysian food and beverage industry

Clean Technologies and Environmental Policy - Food production and consumption is one of the major causes of global environmental degradation. One way to address environmental impacts in the food...     

Interferometric monitoring of satellite longitudes

This paper proposes a technique for monitoring the longitudinal motion of geosynchronous satellites. A two‐antenna interferometer is used, with the baseline orientation adjusted to a particular horizontal azimuth. The interferometer then becomes insensitive to the north–south motion of the satellite, and this enables direct measurement of the satellite's longitudinal motion. Longitudes are monitored continuously, with no delay when orbital manoeuvres occur. The proposed technique is particularly useful when two or more satellites are operating in close proximity and their longitudes must be precisely monitored for safety control. Copyright © 2005 John Wiley & Sons, Ltd.     

Isothermal interphase diffusion with consecutive reactions

For multi-step heterogeneous consecutive reactions affected entirely by interphase diffusion under isothermal condition, the equations for the effectiveness factors, the surface concentrations and the point yields were derived in terms of the Damkoehler numbers or the measurables from the mass balances set up on the assumption that the mass-transfer rate balances the surface-reaction rate at steady state. From the analyses of the equations derived, the effectiveness factors for the intermediate steps and the surface concentrations of intermediates were understood to be enhanced by the measurables inclusive of the concentrations and the mass-transfer coefficients. Then the effect of the concentrations was concluded to be most significant. The effects of these measurables to the effectiveness factors and the surface concentrations were qualitatively discussed for simple consecutive reactions and also for additive consecutive reactions. Especially, as for two-step additive consecutive reactions, the effects of measurables η Da and the concentrations to the effectiveness factors were examined with graphical presentations. Finally, the brief discussion of the dependency of the Damkoehler number upon reaction time and the effect of the Renolds number and diffusivity to the extent of the mass-transfer resistance were presented.     

Trenched‐Sinker LDMOSFET (TS‐LDMOS) Structure for 2 GHz Power Amplifiers

This paper proposes a new LDMOSFET structure with a trenched sinker for high‐power RF amplifiers. Using a low‐temperature, deep‐trench technology, we succeeded in drastically shrinking the sinker area to one‐third the size of the conventional diffusion‐type structure. The RF performance of the proposed device with a channel width of 5 mm showed a small signal gain of 16.5 dB and a maximum peak power of 32 dBm with a power‐added efficiency of 25% at 2 GHz. Furthermore, the trench sinker, which was applied to the guard ring to suppress coupling between inductors, showed an excellent blocking performance below ?40 dB at a frequency of up to 20 GHz. These results confirm that the proposed trenched sinker should be an effective technology both as a compact sinker for RF power devices and as a guard ring against coupling.     

A WDM-PON Employing Fabry–PÉrot Laser Diodes Without a Seed Light Injection

We propose and demonstrate a wavelength-division-multiplexed passive optical network by employing double-contact Fabry-Perot laser diodes (F-P LDs) without a seed light injection. To avoid the high mode partition noise at low frequency, we use a binary phase-shift keying as a modulation format at a low relative intensity noise window. An error-free transmission is achieved by compensating a lasing envelope shift due to temperature variation with the double-contact F-P LD.     

Preparation of spinel-type ferrite thin films by the dip-coating process and their magnetic properties

Films of spinel-type ferrite, MFe₂O₄ (M=Ni, Co, Mg, Li_0.5Fe_0.5) have been prepared by a dip-coating method from the sol-gel process. Ferric nitrate, nickel nitrate, cobalt nitrate and lithium nitrate were used as raw materials, and glycerol and formamide were used as solvents. A film was prepared by dipping a silica glass plate. The spinel-type ferrite was obtained by heat-treatment at 700–900°C for 2 h in air. The film thickness was about 0.8 m. The saturation magnetization, _r, of the film and powder with composition 50NiO·50Fe₂O₃ was 196 emu cm^–3 and 29.1 emu g^–1, respectively, and the coercive force,H _c, was 140 and 95 Oe, respectively, after heat-treatment at 800°C for 2 h. In particular, the films were shown to have a much largerH _c than the powder. The grain growth of spinel ferrite may be subject to restriction because it is in progress above an amorphous base-plate. The crystals are therefore aligned with the base-plate and have uniaxial anisotropy.     

Applications of Mesenchymal Stem Cells in Skin Regeneration and Rejuvenation

Mesenchymal stem cells (MSCs) are multipotent stem cells derived from adult stem cells. Primary MSCs can be obtained from diverse sources, including bone marrow, adipose tissue, and umbilical cord blood. Recently, MSCs have been recognized as therapeutic agents for skin regeneration and rejuvenation. The skin can be damaged by wounds, caused by cutting or breaking of the tissue, and burns. Moreover, skin aging is a process that occurs naturally but can be worsened by environmental pollution, exposure to ultraviolet radiation, alcohol consumption, tobacco use, and undernourishment. MSCs have healing capacities that can be applied in damaged and aged skin. In skin regeneration, MSCs increase cell proliferation and neovascularization, and decrease inflammation in skin injury lesions. In skin rejuvenation, MSCs lead to production of collagen and elastic fibers, inhibition of metalloproteinase activation, and promote protection from ultraviolet radiation-induced senescence. In this review, we focus on how MSCs and MSC-derived molecules improve diseased and aged skin. Additionally, we emphasize that induced pluripotent stem cell (iPSC)-derived MSCs are potentially advanced MSCs, which are suitable for cell therapy.     

Poly(trimethylene terephthalate) nanocomposite fibers comprising different organoclays: Thermomechanical properties and morphology

Poly(trimethylene terephthalate) (PTT) nano composites were synthesized by in situ polymerization at high temperature with two thermally stable organoclays: 1,2‐dimethylhexadecylimidazolium‐montmorillonite (IMD‐MMT) and dodecyltriphenyl phosphonium‐MMT (C₁₂PPh‐MMT). PTT hybrid fibers with various organoclay contents were melt‐spun at various draw ratios (DRs) to produce monofilaments. The thermomechanical properties and morphologies of the PTT hybrid fibers were characterized using differential scanning calorimetry, thermogravimetric analysis, wide‐angle X‐ray diffraction, electron microscopy, and mechanical tensile properties analysis. The nanostructure of the hybrid fibers was observed by both scanning and transmission electron microscopy, which showed that the clay layers were well dispersed into the matrix polymer, although some clusters or agglomerated particles were also detected. Unlike the hybrids containing IMD‐MMT, the clay layers of the C₁₂PPh‐MMT hybrid fiber were more dispersed into the matrix polymer. The thermal stability and tensile properties of the hybrid fibers increased with increasing clay content for DR = 1. However, as DR increased from 1 to 9 the ultimate strength and initial modulus of the hybrid fibers with IMD‐MMT increased slightly whereas those of C₁₂PPh‐MMT hybrid fibers decreased slightly. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4535–4545, 2006     

Preparation of poly(ethylene terephthalate) nanocomposite fibers incorporating a thermally stable organoclay

Summary A series of poly(ethylene terephthalate) (PET) nanocomposites containing organically-modified mica (HB-Mica) were prepared by in-situ interlayer polymerization of dimethyl terephthalate and ethylene glycol. The PET nanocomposites, which contained organoclay loadings of 0 to 2 wt %, were melt-spun to produce monofilaments with various draw ratios. Some of the clay particles appeared well dispersed within the PET matrix, while others were found to form agglomerates with sizes greater than 20 nm. The addition of a small amount of organoclay was sufficient to improve the thermo-mechanical properties of the PET hybrid fibers. Both the thermal stability and the mechanical tensile properties increased with increasing clay content for draw ratios of 1–16.     

Polyurethane–poly(methyl methacrylate) block copolymer dispersions through polyurethane macroiniferters

Polyurethane macroiniferter/poly(methyl methacrylate) block copolymer dispersions with inverse core‐shell morphologies were obtained from 1,1,2,2,‐tetraphenylethane‐1,2‐diol, dimethylol propionic acid, 4,4′‐diphenylmethane diisocyanate, and poly(propylene glycol) via a living radical mechanism. Molecular weight, particle size and dispersion viscosity, and thermal, mechanical, and dynamic mechanical properties of the dispersion cast films are reported as a function of copolymerization time. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1971–1975, 2003