Effect of waste serpentine on the properties of basic insulating refractories

Basic insulating refractories were fabricated by the pressing route using dead-burned magnesia, pure calcined alumina, expanded perlite, and calcined waste serpentine as starting raw materials in four compositions from F1 to F4. Periclase and forsterite were major phases in F1 and F2 compositions, while spinel was also detected in the XRD patterns of F3 and F4 samples. Quantitative phase analysis showed that F4 sample sintered at 1450?°C has the highest forsterite content among all other samples. On the other hand, it has lower thermal conductivity compared to F1 to F3, and even lower than aluminosilicate IFBs with the same bulk density. It is concluded that forsterite is a highly insulating material, compared to periclase, corundum, periclase-spinel, aluminosilicates, such as mullite, etc.     

Biosorption of cesium by native and chemically modified biomass of marine algae: introduce the new biosorbents for biotechnology applications

Biosorption batch experiments were conducted to determine the cesium binding ability of native biomass and chemically modified biosorbents derived from marine algae, namely ferrocyanide algal sorbents type 1 and type 2 (FASs1 and FASs2). The applicability of the Langmuir and Freundlich isotherms for representation of the experimental data was investigated. The cesium sorption performances of the various types of sorbents were compared using the maximum capacities (qmax values) obtained from fitting the Langmuir isotherm to the values calculated from the sorption experiments, which FASs type 1 and type 2 showed better sorption performances for cesium. FASs1 and FASs2 derived from formaldehyde and glutaraldehyde crosslinked Padina australis exhibited lower sorption capacities than those prepared from the non-crosslinked one. Most of the cesium ions were bound to FASs1, derived from Sargassum glaucescens and P. australis, in < 2 min and equilibrium reached within the first 30 min of contact. Biosorption of cesium by FASs1 derived from P. australis and Cystoseria indica was constantly occurred at a wide range of pH, between 1 and 10, and the highest removal took place at pH 4. The presence of sodium and potassium at 0.5 and 1mM did not inhibit cesium biosorption by algae biomass. The maximum cesium uptake was acquired using the large particles of FAS2 originated from S. glaucescens (2-4 mm). Desorption of cesium from the metal-laden FASs1 (from P. australis, S. glaucescens and Dictyota indica) was completely achieved applying 0.5 and 1 M NaOH and KOH, although the cesium sorption capacity of the biosorbents (from C. indica and S. glaucescens) decreased by 46-51% after 9 sorption-desorption cycles.     

Effect of side slope of main channels on formation and penetration of scour hole in confluences

In an open‐channel confluence, deep scour holes and depositional point bars are usually formed due to high bed‐shear stresses and secondary circulations. In the present study, presuming the effectiveness of channel geometry on the flow dynamics at the confluence, some variables including different side slope angles of the main channel (θ = 45°, 60°, 75°, 90°), lateral to downstream discharge ratio (Q_r), and downstream densimetric Froude number (Fr_g3) were experimentally studied under clear‐water condition for the confluence angle α = 90°. According to the results, the increase of θ led to a greater penetration of scour hole across the main and tributary channels, whereas a little scour development was observed along those channels. Meanwhile, an increase in Q_r and Fr_g3 caused further scouring, but their effects on the dimensions of scour hole diminished with increase of θ. Thus, with increase of Q_r from 0.194 to 0.552, the mean penetration rate of scour hole to all directions for θ = 45°, 60°, 75°, and 90° was obtained 42.8%, 32.4%, 25%, and 20.5%, respectively. In addition, considering the effect of θ, Q_r, and Fr_g3, some empirical relationships were obtained for estimating the penetration length of scour hole. The derived relationships show that Fr_g3 plays more important role on the dimensions of scour hole than θ.     

Regional water quality management for the Karun–Dez River basin, Iran

To achieve water quality goals in a river basin, a water quality management model (WQMM) has been developed through the geographic information system (GIS) approach and a mathematical water quality model. The developed model has been applied to the Karun and Dez Rivers, where water quality has decreased due to heavy pollutant loads from Khuzestan province cities and surrounding areas. Pollution sources, land use, geographic features and measured water quality data of the river basin were incorporated into the Arc‐View GIS database. With the database, the management model calculated management type and management cost for each management project in the river basin. Until now, river management policy for polluted rivers in Iran first penalizes pollution sources and then constructs treatment plants for the pollution sources whose wastewater is released untreated and for which the wastewater quality goal of the Iranian Department of Environment is not met. Different management projects with a time programme were proposed and they were compared with the results of the river quality without any management approach. It became clear that the results based on the management approach were much better than those for the unmanaged condition from the viewpoint of the achievement of water quality goals and cost optimization.     

The excellent photocatalytic activity of novel Cs3PW12O40/WO3 composite toward the degradation of rhodamine B

In this paper, a simple one-pot thermal decomposition method was successfully used to synthesize a novel Cs₃PW₁₂O₄₀/WO₃ composite for the first time. The synthesized composite was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), FTIR, diffuse reflectance spectroscopy (DRS) and N₂ adsorption-desorption techniques. The photocatalytic activity to degrade RhB molecules over Cs₃PW₁₂O₄₀/WO₃ composite was evaluated under xenon light irradiation. The results indicated the complete degradation of RhB molecules over Cs₃PW₁₂O₄₀/WO₃ composite after 30?min irradiation. However, the photocatalytic degradation of RhB over WO₃ and Cs₃PW₁₂O₄₀ after 80?min light irradiation are nearly 52%, and 68%, respectively. The enhanced photocatalytic activity of Cs₃PW₁₂O₄₀/WO₃ composite compared with WO₃, and Cs₃PW₁₂O₄₀ was ascribed to the strong interaction between WO₃ and Cs₃PW₁₂O₄₀, which effectively reduces the recombination of photogenerated electron-hole pairs. Based on experimental results, the possible mechanism of photocatalytic reactions on the Cs₃PW₁₂O₄₀/WO₃ composite photocatalyst was investigated, and the hydroxyl radical (OH) and superoxide radical (O₂^?) were determined as the main active species in the photocatalytic degradation of RhB over Cs₃PW₁₂O₄₀/WO₃ composite.     

Evaluation of lubricant condition and engine health based on soft computing methods

Neural Computing and Applications - Evaluating the condition of the lubricant plays an influential role in the maintenance engineering of mechanical systems. This study has several objectives and...     

Direct-write fabrication of freestanding nanocomposite strain sensors

This paper deals with the design and microfabrication of two three-dimensional (3D) freestanding patterned strain sensors made of single-walled carbon nanotube (SWCNT) nanocomposites with the ultraviolet-assisted direct-write (UV-DW) technique. The first sensor consisted of three nanocomposite microfibers suspended between two rectangular epoxy pads. The flexibility of the UV-DW technique enables the sensor and its housing to be manufactured in one monolithic structure. The second sensor was composed of a nanocomposite network consisting of four parallel microsprings, which demonstrates the high capability of the technique when compared to conventional photolithographic technologies. The performances of the sensors were assessed under tension and compression, respectively. The sensors' sensitivities were evaluated by correlating their measured resistivities to the applied displacements/strains. Electrical conductivity measurements revealed that the manufactured sensors are highly sensitive to small mechanical disturbances, especially for lower nanotube loadings when compared to traditional metallic or nanocomposite films. The present manufacturing method offers a new perspective for manufacturing highly sensitive 3D freestanding microstructured sensors.     

A digital frequency independent phase meter

A digital, frequency-independent phase meter is described. It makes use of pulses derived from the multiplication of the frequency of the reference input signal as its clock pulses instead of conventional crystal controlled clock generators. Advantages of the meter include simplicity and the elimination of gating error. The main source of error for this circuit is harmonic distortion of the input signals     

A high resolution digital frequency meter for low frequencies

A digital frequency meter using frequency multiplication is described. It can be used in utility power system control centers and other low-frequency applications where resolutions of the order of 1/100 Hz and almost instantaneous readouts are essential. Possible improvements of the circuit are suggested     

Effect of Notch Location on Fatigue Life Prediction of Strength Mismatched HSLA Steel Weldments

Welding of high strength low alloy steels (HSLA) involves usage of low, even and high strength filler materials (electrodes) than the parent material depending on the application of the welded structures and the availability of the filler material. In the present investigation, the fatigue crack growth behaviour of weld metal (WM) and heat affected zone (HAZ) regions of under matched (UM), equal matched (EM) and over matched (OM) joints has been studied. The base material used in this investigation is HSLA-80 steel of weldable grade. Shielded metal arc welding (SMAW) process has been used to fabricate the butt joints. Centre cracked tension (CCT) specimen has been used to evaluate the fatigue crack growth behaviour of the welded joints. Fatigue crack growth experiments have been conducted using servo hydraulic controlled fatigue testing machine at constant amplitude loading (R=0). A method has been proposed to predict the fatigue life of HSLA steel welds using fracture mechanics approach by incorporatin