Essential phospholipids in the treatment of chronic pyelonephritis]

Through TCD test, observation on the blood flow dynamics change before and after treatment with 31 cases of the child cerebral atrophy was made. It is found that scalp therapy is able to speed up the blood flow of part artery, especially increase the even blood flow speed of MCA, ACA obviously (P < 0.05), which preliminary shows the mechanism of scalp therapy for child cerebral atrophy mean while. It is found that scalp therapy also has the function to restrain epilepsy.     

Method of detecting and measuring low amplitude potentials in bioelectric signals

A method is proposed for detecting and measuring the late potentials of the ventricles of the heat (LPV). The method is based on computations of the amplitude, time, and spectral parameters of the signal. Examples are given of the use of the method in patients with or without LPV. Translated from Izmeritel'naya Tekhnika, No. 2, pp. 57–59, February, 1996.     

Resonant Quantum Phenomena for an rf-SQUID: Moderate Underdamped and Extreme Underdamped Limit

We study the resonant quantum behaviour of a macroscopic superconducting system interacting with an external field. First we consider the resonant tunneling assisted by microwave frequency in the moderate underdamped quantum regime. Then we consider the resonant process in the extreme underdamped limit. In both regimes we have investigated a small frequency range, where resonant phenomena take place. The transition probability W from the left to the right potential well has been numerically calculated for an rf-SQUID as function of the external flux φ _x for both regimes. Results indicate that, in a proper frequency and φ _x range, the transition probability W can present two or three resonant peaks, depending on the damping regime.     

Synthesis of Titanates with a Ramsdellite-Type Tunnel Structure Crystallizing in the Li<Subscript>2</Subscript>O-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript> System in Different Gaseous Media

The ramsdellite-type phases crystallizing in the Li₂O-Fe₂O₃-TiO₂ system in the course of synthesis in gaseous media at different oxygen partial pressures are studied. Solid solutions based on the ramsdellite structure with the composition Li₂Ti_3?xFe _x O_{7 ? δ} (0 ≤ x ≤ 0.7) are prepared in an oxidizing medium (P_O2 = 1 atm) for the first time. Analysis of the results obtained by electron paramagnetic resonance and Mossbauer spectroscopy revealed that, in these solid solutions, all iron ions are in the oxidation state Fe⁺³.     

Upper limit ofTc for the copper oxides

The value of the critical temperature of the cuprates correlates with the doping level and is affected by the interplay of two competing factors: (1) the increase in carrier concentration, and (2) the pair-breaking effect of magnetic impurities. An analysis of the temperature dependence of the critical field leads to the conclusion that magnetic impurities are present even in a sample with the maximum observed value ofT _c.A new parameter, intrinsicT _c (T _cintr), which is its value in the absence of magnetic impurities, is introduced. The maximum value ofT _cintr, which corresponds to the maximum doping level, appears to be similar for different cuprates and to be equal to 160–170 K. This is the upper limit ofT _c in the cuprates.     

Synthesis of thin p-type rutile films

The structure and electrical and optical properties of heterostructures formed on the surface of single-crystal silicon wafers as a result of the heat treatment and pulsed photon treatment of Ti films in oxygen, air, and nitrogen are investigated. It is shown that a TiO₂/Ti₅Si₃/p-Si heterostructure is formed upon heat treatment in air, whereas a TiO₂/TiSi₂/p-Si heterostructure is formed upon photon treatment. It is established that rutile films with pronounced n-type conductivity are formed as a result of the heat treatment of Ni-doped Ti films in oxygen. Rutile films with p-type conductivity are formed upon the thermal annealing of Ti films in air with subsequent photon treatment in nitrogen.     

Tool–workpiece interaction in deformational cutting

A method is developed for the comparison of deformational cutting and traditional cutting in terms of the force and energy consumption. The force required is less in deformational cutting than in traditional cutting.