The frequent evocative comparisons between music and architecture in the text of the Modulor may explain why Le Corbusier, in this constant search for ordering principles, considered his proportional sequence to be equivalent to a musical scale. Yet, since the dimensional ratios of Le Corbusier’s ‘scale’ are much larger than the pitch ratios of the latter, the Modulor comes much closer to another structural element of music, that of harmony. By adjusting the Modulor ratios to the corresponding ratios of musical chords, three variants of a “musical” Modulor can be generated – Chromatic, Major and Minor. If, in addition, the two sets of the malebased Modulor dimensions are replaced with a universal female-male set, the inherently complex Modulor numbers become simpler and clear. The Master’s intention of producing a rational and practical system of proportions, which is related to both the scale of the human being, and to the order inherent in the physical nature of sound, can thus be realized. 相似文献
We adapt the technology acceptance model (TAM) to examine the factors influencing mobile gaming adoption among “global youth.” Our model replaces usefulness with convenience, incorporating visual appeal and escapism as antecedents of fun, and perceived novelty and economic value as antecedents of convenience. Questionnaire surveys were conducted in the U.S., Spain, and the Czech Republic, producing 432 usable responses. In the structural model assessment with the pooled sample, convenience exercises greater effects on attitude toward mobile games than fun, suggesting that the most important driver is probably the capability of being used flexibly at any time and in any place, rather than mere enjoyment. Tests of latent means suggest that most dimensions are perceived more strongly in the Czech Republic.相似文献
Thermal stability, mechanism, and kinetics of thermally induced microstructural transformations and their effects on magnetic permeability of Fe72Si15B8V4Cu1 alloy with combined amorphous/nanocrystalline structure were studied. DTA curves revealed two separated thermally activated exothermic events in the temperature ranges from 740 K to 820 K (467 °C to 547 °C) and 870 K to 930 K (597 °C to 657 °C). Crystalline phases present in the as-prepared and thermally treated alloy samples were identified, and their microstructural parameters were determined using XRD, while, to gain further insight into the mechanism of microstructural transformations, AFM and SEM–EDS analyses were performed. Deconvolution of the complex DTA peak into individual steps was conducted, and, in correlation with the results of microstructural analysis, kinetic triplets corresponding to individual transformation steps were determined, allowing for the estimation of the lifetimes of the alloy at different temperatures. Magnetic permeability measurements showed that, in spite of the influence of microstructural transformations on magnetic properties of the alloy, the favorable magnetic properties are retained over relatively a wide temperature range.
Due to uncomfortable injection regimens of peptidic agonists of glucagon-like peptide-1 receptor (GLP-1R), orally available nonpeptide positive allosteric modulators (PAMs) of GLP-1Rs are foreseen as the possible future mainstream therapy for type 2 diabetes. Herein, current GLP-1R PAMs are reviewed. Based on the effectiveness and in silico predicted physicochemical properties, pharmacokinetics, and toxicity, possible candidates for further development as oral drugs were selected. The suggestion is that GLP-1R PAMs might be used orally alone or in combination with dipeptidyl peptidase-4 (DPP-4) inhibitors, which could offer an optimal treatment option next to metformin monotherapy in type 2 diabetes mellitus, or in a wider spectrum of indications. Quercetin acts as a GLP-1R PAM and DPP-4 inhibitor, and therefore, might be considered as a pioneering agent with a dual mechanism of action, in terms of GLP-1R positive allosteric modulation and DPP-4 inhibition for potentiating GLP-1 dependent effects. 相似文献
WC–Co cemented carbide has been investigated using instrumented indentation with maximum applied loads from 0.1 to 10 mN. The hardness and indentation modulus of individual phases and the influence of crystallographic orientation of WC on the hardness and indentation modulus have been studied. The hardness of the Co binder was approximately 10 GPa and that of WC grains up to 50 GPa with relatively large scatter under the indentation load of 1 mN. Investigation of the role of crystallographic orientation of WC grains on hardness at 10 mN load revealed average values of HITbasal = 40.4 GPa (EITbasal = 674 GPa) and HITprismatic = 32.8 GPa (EItprismatic = 542 GPa), respectively. The scatter in the measured values at low indentation loads is caused by the effects of surface and sub-surface characteristics (residual stress, damaged region) and at higher loads by “mix-phase” volume below the indenter. 相似文献
This paper is concerned with the use of microprocessors for control of knee joint locking and unlocking in a prosthesis or orthosis. Inputs to the controller are provided by the wearer and by artificial proprioceptive and exteroceptive sensors. The functioning of an experimental orthotic system is explained and preliminary test results obtained with normal subjects are presented. 相似文献
Pulsating potential electrolysis has been applied to one typical electrocatalytic reaction ie, the oxidation of formic acid on platinum and platinum partially covered by lead adatoms electrodes. It has been found that much higher average cds can be obtained with such regimes than in constant potential electrolysis. The effect can be of considerable interest for the application in electrochemical power sources. An analysis of the mechanism of effects of pulsating potentials has been given. A calculated frequency dependence of the average current density is in agreement with experimental one for both electrodes. 相似文献
This note discusses the effects of the electrode position scaling on the realistic Laplacian (RL) computation. It is shown that when the RL is estimated with the help of Tikhonov regularization and the generalized cross-validation (GCV) criterion, improper electrode position scaling may influence the GCV criterion, which results in the decrease of RL precision. We identify what the proper scaling should be, and we provide a closer examination of how the GCV criterion is affected by the electrode position scaling. 相似文献
This paper explores regularization options for the ill-posed spline coefficient equations in the realistic Laplacian computation. We investigate the use of the Tikhonov regularization, truncated singular value decomposition, and the so-called lambda-correction with the regularization parameter chosen by the L-curve, generalized cross-validation, quasi-optimality, and the discrepancy principle criteria. The provided range of regularization techniques is much wider than in the previous works. The improvement of the realistic Laplacian is investigated by simulations on the three-shell spherical head model. The conclusion is that the best performance is provided by the combination of the Tikhonov regularization and the generalized cross-validation criterion-a combination that has never been suggested for this task before. 相似文献