Review on zirconate-cerate-based electrolytes for proton-conducting solid oxide fuel cell

The performance of low-to-intermediate temperature (400–800?°C) solid oxide fuel cells (SOFCs) depends on the properties of electrolyte used. SOFC performance can be enhanced by replacing electrolyte materials from conventional oxide ion (O^2-) conductors with proton (H⁺) conductors because H⁺ conductors have higher ionic conductivity and theoretical electrical efficiency than O^2- conductors within the target temperature range. Electrolytes based on cerate and/or zirconate have been proposed as potential H⁺ conductors. Cerate-based electrolytes have the highest H⁺ conductivity, but they are chemically and thermally unstable during redox cycles, whereas zirconate-based electrolytes exhibit the opposite properties. Thus, tailoring the properties of cerate and/or zirconate electrolytes by doping with rare-earth metals has become a main concern for many researchers to further improve the ionic conductivity and stability of electrolytes. This article provides an overview on the properties of four types of cerate and/or zirconate electrolytes including cerate-based, zirconate-based, single-doped cerate–zirconate and hybrid-doped cerate–zirconate. The properties of the proton electrolytes such as ionic conductivity, chemical stability and sinterability are also systematically discussed. This review further provides a summary of the performance of SOFCs operated with cerate and/or zirconate proton conductors and the actual potential of these materials as alternative electrolytes for proton-conducting SOFC application.     

Stabilization of 6H-Hexagonal SrMnO3 Polymorph by Al2O3 insertion

We demonstrate the structural evolution of polymorphic phases in Al₂O₃-inserted SrMnO₃ ceramics synthesized by solid state reaction. While the 4H-hexagonal phase is predominant in pure SrMnO₃ ceramics, a small amount of 6H-hexagonal polymorph is identified in addition to the primary 4H-hexagonal SrMnO₃ and the secondary hexagonal SrAl₂O₄ phases in the as-sintered ceramics, evidenced by x-ray diffraction and subsequent Rietveld refinement analyses. The existence of the 6H-hexagonal SrMnO₃ phase is corroborated using Raman spectroscopy. The chemical compositions and electronic structures of the Al₂O₃-inserted SrMnO₃ compounds are also examined using energy dispersive spectroscopy and x-ray photoelectron spectroscopy, respectively. The first-principles calculations reveal that there is no clear difference between the total energies of 4H- and 6H-hexagonal polymorphs regardless of the presence/absence of Sr and oxygen vacancies. Possible origins are discussed with the estimation of actual strain based on the refined lattice parameter of 6H SrMnO₃.     

Damage mechanism at different transpassive potentials of solution-annealed 316 and 316l stainless steels

Electrochemical impedance spectroscopy (EIS), anodic polarization and scanning electron microscopy techniques were used to investigate the damage mechanism in the transpassive potential region of AISI ...     

A Mobile Cloud-Based eHealth Scheme

Mobile cloud computing is an emerging field that is gaining popularity across borders at a rapid pace. Similarly, the field of health informatics is also considered as an extremely important field. This work observes the collaboration between these two fields to solve the traditional problem of extracting Electrocardiogram signals from trace reports and then performing analysis. The developed system has two front ends, the first dedicated for the user to perform the photographing of the trace report. Once the photographing is complete, mobile computing is used to extract the signal. Once the signal is extracted, it is uploaded into the server and further analysis is performed on the signal in the cloud. Once this is done, the second interface, intended for the use of the physician, can download and view the trace from the cloud. The data is securely held using a password-based authentication method. The system presented here is one of the first attempts at delivering the total solution, and after further upgrades, it will be possible to deploy the system in a commercial setting.     

Prediction of ultrasonic wave velocity in particleboard and fiberboard

Ultrasonic wave velocities were determined at parallel and perpendicular to manufacturing direction and at the interval angles of 15° in clockwise and counterclockwise directions of particleboard and fiberboard. The experimental results were compared with the predicted values using some empirical formulae such as Hankinson and Jacoby equations. The results showed that the ultrasonic wave velocity were the highest in parallel direction in particleboard and fiberboard and decreases with increase of angle and the lowest values occurred in perpendicular direction. The predicted ultrasonic velocity using Hankinson and Jacoby equations are in close agreement with the measured values. Relationship between ultrasonic wave velocities and particles and fibers angle could be successfully presented by cubic and quadratic regression equations as well.     

Material state remapping in computational solid mechanics

A computational procedure for remapping material state information from one finite element mesh to another is described. The procedure is useful in connection with evolving meshes for inelastic problems, as for example occur in the context of fracture simulation and adaptive mesh refinement. The proposed method is based on weak enforcement of equality between corresponding fields on the two meshes, where piecewise‐constant fields on both meshes are generalized from the quadrature‐point values. The essential algorithmic problem is that of calculating the volume partition of an arbitrary convex region with respect to a covering set of disjoint convex regions. Instead of geometrically resolving the associated intersections, the problem is herein approximated by a constrained optimization problem, which may be readily and efficiently solved computationally. This formulation is a main contribution of the paper. Computational examples are given that illustrate the effectiveness of the proposed procedure. Copyright © 2002 John Wiley & Sons, Ltd.     

Anthocyanins characterization of 15 Iranian pomegranate (Punica granatum L.) varieties and their variation after cold storage and pasteurization

Anthocyanins (ACs) are phenolic compounds that are distributed widely in fruits and vegetables. Apart from imparting color to plants, ACs also have an array of health-promoting benefits. In this research, the amounts of major ACs of 15 pomegranate (Punica granatum L.) varieties obtained from Yazd province were determined. The major ACs detected in the studied varieties were as follows: delphinidin 3-glucoside (2.19–16.29 mg/L), delphinidin 3,5-diglucoside (2.36–63.07 mg/L), pelargonidin 3-glucoside (0.26–1.36 mg/L), pelargonidin 3,5-diglucoside (0.01–8.11 mg/L), cyanidin 3-glucoside (5.78–30.38 mg/L), and cyanidin 3,5-diglucoside (4.39–166.32 mg/L). The effect of storage time of unprocessed and pasteurized juices on ACs content of four selected varieties was also studied. Average degradation percentage of each AC was between 23.0 and 83.0% during 10 days at 4 °C. Moreover, in pasteurized juices average degradation of ACs was 42.8 ± 0.5% after 10 weeks storage at 4 °C.     

Intelligent non-linear modelling of an industrial winding process using recurrent local linear neuro-fuzzy networks

This study deals with the neuro-fuzzy (NF) modelling of a real industrial winding process in which the acquired NF model can be exploited to improve control performance and achieve a robust fault-tolerant system. A new simulator model is proposed for a winding process using non-linear identification based on a recurrent local linear neuro-fuzzy (RLLNF) network trained by local linear model tree (LOLIMOT), which is an incremental tree-based learning algorithm. The proposed NF models are compared with other known intelligent identifiers, namely multilayer perceptron (MLP) and radial basis function (RBF). Comparison of our proposed non-linear models and associated models obtained through the least square error (LSE) technique (the optimal modelling method for linear systems) confirms that the winding process is a non-linear system. Experimental results show the effectiveness of our proposed NF modelling approach.     

On the application of Harris hawks optimization (HHO) algorithm to the design of microchannel heat sinks

Engineering with Computers - A novel Harris hawks optimization algorithm is applied to microchannel heat sinks for the minimization of entropy generation. In the formulation of the heat transfer...