Statistical evaluation of the damage potential of earthquake ground motions

This study focuses on the damage potential of earthquake ground motions based on the inelastic dynamic response of equivalent single degree of freedom structures. Their yield resistances are selected in accordance with seismic design codes. An index accounting for the accumulation of damage due to inelastic excursions is used to represent structural damage. A set of 94 ground motions are employed for this analysis, which are all scaled to the same peak ground acceleration of 0.4 g. Earthquake ground motions are classified with respect to both the ratio of peak velocity to peak acceleration (V/A ratio) and their effective excitation duration. The effect of these parameters on damage potential is investigated by using sensitivity analysis and probabilistic techniques. It is concluded that both V/A ratio and effective duration significantly influence the damage potential of earthquake ground motions, although they are not represented appropriately by the spectral definitions of earthquake excitations in seismic design codes.     

Investigation of carbon contamination in lost foam castings of low carbon steel

Lost foam casting(LFC) process is a special casting method in which polymeric foam patterns with refractory coatings are utilized as a mould component. In this work, four types of foam: expandable polyethylene(EPE), expandable polypropylene(EPP) and expandable polystyrene(EPS) foams with two different densities were employed as pattern materials. LFC and conventional green sand mould casting methods were used to cast a low carbon steel, A216 Grade WCB. Both casting processes were carried out at 1,580 °C. Chemical analysis results showed that the carbon contamination level was high and was influenced by pattern type. Metallographic investigations revealed a significant increase in the percentage of pearlite phase in all LFC samples. Densities of manufactured samples were calculated in order to evaluate porosity of the products. It was determined that the densities of the LFC samples were lower than the green sand mould cast reference sample(RS). Vickers hardness tests were also carried out and increments in hardness values with increased carbon content was observed.     

Rapid and Digital Detection of Inflammatory Biomarkers Enabled by a Novel Portable Nanoplasmonic Imager

New point‐of‐care diagnostic devices are urgently needed for rapid and accurate diagnosis, particularly in the management of life‐threatening infections and sepsis, where immediate treatment is key. Sepsis is a critical condition caused by systemic response to infection, with chances of survival drastically decreasing every hour. A novel portable biosensor based on nanoparticle‐enhanced digital plasmonic imaging is reported for rapid and sensitive detection of two sepsis‐related inflammatory biomarkers, procalcitonin (PCT) and C‐reactive protein (CRP) directly from blood serum. The device achieves outstanding limit of detection of 21.3 pg mL^?1 for PCT and 36 pg mL^?1 for CRP, and dynamic range of at least three orders of magnitude. The portable device is deployed at Vall d'Hebron University Hospital in Spain and tested with a wide range of patient samples with sepsis, noninfectious systemic inflammatory response syndrome (SIRS), and healthy subjects. The results are validated against ultimate clinical diagnosis and currently used immunoassays, and show that the device provides accurate and robust performance equivalent to gold‐standard laboratory tests. Importantly, the plasmonic imager can enable identification of PCT levels typical of sepsis and SIRS patients in less than 15 min. The compact and low‐cost device is a promising solution for assisting rapid and accurate on‐site sepsis diagnosis.     

Decentralized routing controller design using overlapping decompositions

The use of overlapping decompositions in designing routing controllers for large-scale networks is considered and a decentralized dynamic routing controller design strategy is proposed. The strategy is based on the overlapping decompositions method and can be used for large-scale networks which have more than two overlapping subnetworks and/or have more than one node in the overlapping part. The controller obtained by the proposed strategy is decentralized in the sense that all on-line computations can be done locally at the individual nodes without any information transfer from the other nodes. The controller satisfies all the routing control constraints and it avoids any looping. The controller also clears the queues in finite time in the absence of external arrivals and it keeps the queue lengths bounded in the presence of external arrival rates which do not exceed a certain maximum rate. In order to illustrate the proposed controller's performance, the controller is applied to an example network and some simulation results are presented in a number of cases. Furthermore, a centrally designed controller is also applied to the same network for the same cases, in order to obtain a basis for comparison.     

Software Support for Computerized Electromyography in Clinical Dentistry

This paper describes the software system for a minicomputer-based real-time data-acquisition system that is currently being used by clinical dental personnel of the University of Michigan Dental Research Institute. Because this system is utilized by operators who are unfamiliar with computers it is highly interactive. Also described are the software design considerations engendered by such a research environment.     

Directional double Fano resonances in plasmonic hetero-oligomers

We experimentally demonstrate for the first time a very compact plasmonic hetero-oligomer structure where the multiple radiant and subradiant modes can be tailored independently. Unlike previous approaches based on collective excitations in complex plasmonic systems, we show precise engineering of resonances leading to simultaneous spectral overlap of multiple plasmonic modes with opposite radiative character. This asymmetric behavior combined with inherent spatial features of the structure leads to directional double Fano resonances as shown with numerical analysis. A model based on temporal coupled mode theory is also provided to describe the double Fano behavior.     

Influence of infrared final cooking on polycyclic aromatic hydrocarbon formation in ohmically pre-cooked beef meatballs

Effects of infrared cooking on polycyclic aromatic hydrocarbon (PAH) formation in ohmically pre-cooked beef meatballs were investigated. Samples were pre-cooked in a specially designed-continuous type ohmic cooking at a voltage gradient of 15.26 V/cm for 92 s. Infrared cooking was applied as a final cooking method at different combinations of heat fluxes (3.706, 5.678, 8.475 kW/m²), application distances (10.5, 13.5, 16.5 cm) and application durations (4, 8, 12 min). PAHs were analyzed by using high performance liquid chromatography (HPLC) equipped with a fluorescence detector. The total PAH levels were detected to be between 4.47 and 64 μg/kg. Benzo[a] pyrene (B[a]P) and PAH4 (sum of B[a]P, chrysene (Chr), benzo[a]anthracene (B[a]A) and benzo[b]fluoranthene (B[b]F)) levels detected in meatballs were below the EC limits. Ohmic pre-cooking followed by infrared cooking may be regarded as a safe cooking procedure of meatballs from a PAH contamination point of view.