Bayes estimators for reliability measures in geometric distribution model using masked system life test data

This paper presents Bayes estimators for the reliability measures of the individual components in a multi-component systems in the presence of masked system life test data. The life time distributions of the system components are assumed to be geometric with different parameters. Two-sided Bayesian probability intervals of the parameters are also derived. Numerical simulation study is given in order to: (i) explain how one can apply the theoretical results obtained, (ii) study the influence of the sample size and masking level on the accuracy of point estimates.     

Influence of Aging Parameters on the Tensile Properties and Quality Index of Al-9?Pct Si-1.8?Pct Cu-0.5?Pct Mg 354-Type Casting Alloys

The current study was carried out with a view to investigating the influence of age-hardening parameters, aging temperature and time, on the tensile properties and quality indices of a high-strength Al-9 pct Si casting alloy, namely, 354-Al-9 pct Si-1.8 pct Cu-0.5 pct Mg. Quality charts were used as an evaluation tool for selecting the optimum conditions to be applied, in practice, in order to develop high strength and optimum quality in 354 casting alloy. Aging at a low temperature of 428 K (155 °C) was observed to produce the greatest strength and optimum quality in the 354-type castings compared to aging at higher temperatures. The peak strength observed for 354 alloy may be attained after shorter aging times on the condition that the aging temperature is increased. The aging times required for reaching peak strength in 354 alloys are 72 hours, 40 hours, 8 hours, 1 hour, and 15 minutes at aging temperatures of 428 K, 443 K, 468 K, 493 K, and 518 K (155 °C, 170 °C, 195 °C, 220 °C, and 245 °C), respectively. Aging treatment at higher temperatures is accompanied by a reduction in the tensile properties and quality index values of the castings; however, it also introduces the possibility of a significant economical strategy for minimizing the time and the cost of this same treatment. Aging treatment at a lower temperature of 428 K (155 °C) produces fine and dense precipitates displaying smaller interparticle spacing, while at higher aging temperatures, such as 518 K (245 °C), the precipitates are coarser in size, less dense, and more widely dispersed. The quality charts developed in the course of the current research facilitate the interpretation and evaluation of the tensile properties of the 354 alloy. Such charts provide a logical evaluation tool, from the metallurgical point of view, for an accurate prediction of the influence of aging parameters studied on the properties of the alloys. Depending on the required level of tensile properties and based on the quality charts developed, it is possible to make a rigorous selection as to the most suitable aging parameters to be applied to the 354 alloy so as to obtain the best possible cost-effective compromise between alloy strength and quality.     

Sink-oriented tree based data dissemination protocol for mobile sinks wireless sensor networks

Wireless Networks - Data dissemination toward static sinks causes the nearby nodes to deplete their energy quicker than the other nodes in the field (i.e., this is referred to as the hotspot...     

Channel identifiability under orthogonal space-time coded modulations without training

Space-time block coded (STBC) transmission has been established as an efficient tool to enhance communication performance over wireless fading channels. The success of STBC decoding relies on accurate channel knowledge at receivers. In this work, we present a channel estimation approach that does not require training data to estimate unknown channels. Focusing on STBC from orthogonal designs, we present channel identification conditions that are largely verifiable in terms of the code and the antenna array configuration. We also develop a simple subspace-based algorithm to identify the unknown space-time channel matrix for complex transmission. Finally, we present simulation test results to illustrate the performance of the proposed method.     

Improvement of the cell performance in the ZnS/Cu(In,Ga)Se2 solar cells by the sputter deposition of a bilayer ZnO : Al film

ZnS is a candidate to replace CdS as the buffer layer in Cu(In,Ga)Se₂ (CIGS) solar cells for Cd‐free commercial product. However, the resistance of ZnS is too large, and the photoconductivity is too small. Therefore, the thickness of the ZnS should be as thin as possible. However, a CIGS solar cell with a very thin ZnS buffer layer is vulnerable to the sputtering power of the ZnO : Al window layer deposition because of plasma damage. To improve the efficiency of CIGS solar cells with a chemical‐bath‐deposited ZnS buffer layer, the effect of the plasma damage by the sputter deposition of the ZnO : Al window layer should be understood. We have found that the efficiency of a CIGS solar cell consistently decreases with an increase in the sputtering power for the ZnO : Al window layer deposition onto the ZnS buffer layer because of plasma damage. To protect the ZnS/CIGS interface, a bilayer ZnO : Al film was developed. It consists of a 50‐nm‐thick ZnO : Al plasma protection layer deposited at a sputtering power of 50 W and a 100‐nm‐thick ZnO : Al conducting layer deposited at a sputtering power of 200 W. The introduction of a 50‐nm‐thick ZnO : Al layer deposited at 50 W prevented plasma damage by sputtering, resulting in a high open‐circuit voltage, a large fill factor, and shunt resistance. The ZnS/CIGS solar cell with the bilayer ZnO : Al film yielded a cell efficiency of 14.68%. Therefore, the application of bilayer ZnO : Al film to the window layer is suitable for CIGS solar cells with a ZnS buffer layer. Copyright © 2012 John Wiley & Sons, Ltd.     

A low-dispersion 3-D second-order in time fourth-order in space FDTD scheme (M3d/sub 24/)

A second-order in time fourth-order in space modified finite-difference time-domain (FDTD) scheme for three dimensional electromagnetic problems "M3d/sub 24/" is presented. The algorithm enables the numerical phase error to be minimized, so that it leads to high accuracy with low resolution grids. The advantage of this method is demonstrated by considering the long distance propagation of the wave radiated from a time harmonic elementary dipole using a low resolution grid, and comparing the results with other FDTD schemes.     

Reducible rank codes and their applications to cryptography

We present a new family of so-called reducible rank codes which are a generalization of rank product codes . This family includes maximal rank distance (MRD) codes for lengths n>N in the field F/sub N/. We give methods for encoding and decoding reducible rank codes. A public key cryptosystem based on these codes and on the idea of a column scrambler is proposed. The column scrambler "mixes" columns of a generator (parity-check) matrix of a code. It makes the system more resistant to structural attacks such as Gibson's attacks. Possible attacks on the system are thoroughly studied. The system is found to be secure against known attacks for public keys of about 16 kbits and greater.     

Blind Channel Identifiability for Generic Linear Space-Time Block Codes

Linear space-time block codes (STBCs) have proven their effectiveness in performance improvement of wireless multiple-input multiple-output communication systems. Their successful decoding, however, requires reliable channel knowledge at the receiver. In this paper, we present a semiblind channel estimation method for linear STBC without the usual code orthogonality condition. We provide a set of identification conditions that are mostly verifiable a priori in terms of code parameters and antenna array configuration. We also present a simple channel estimation algorithm. Finally, we provide simulation results that illustrate the performance of the proposed scheme     

Substitution of wheat starch with non-wheat starches and cross-linked waxy barley starch affects sensory properties and staling of Arabic bread

Substitution of starch from barley, corn, oat, potato, rice or sorghum for prime wheat starch in the formulation of Arabic bread resulted in breads with significantly (P < 0.05) different textural attributes from regular wheat bread except for barley starch. Substitution of waxy barley starch (957 g kg⁻¹ amylopectin) for wheat starch (279 g kg⁻¹ amylopectin) resulted in bread that was not significantly different from regular wheat bread when assessed in the fresh state. However, upon aging, the waxy barley starch-containing bread staled at a significantly (P < 0.05) faster rate than regular wheat bread. Breads made with waxy barley starch cross-linked with 50, 200 or 500 ppm phosphorus oxychloride showed higher enthalpy of melting (ΔH) upon aging and staled faster than the bread formulated with waxy barley starch. These findings suggest that amylopectin retrogradation is one of the determinants of Arabic bread staling and that cross-linking promotes recrystallisation of amylopectin, possibly by keeping the polymer chains in close proximity. The rate of staling in breads formulated with cross-linked waxy barley starch decreased with increasing levels of cross-linking, possibly owing to restrictions in the degree of starch swelling. © 1999 Society of Chemical Industry