Novel pearl millet couscous process for West African markets using a low-cost single-screw extruder

Traditional West African pearl millet couscous products are popular; however, their preparation is laborious, time-consuming and energy-demanding, involving agglomeration, steaming, drying and sieving steps. In this study, a process was developed to produce millet couscous using a high pressure, high temperature and low-cost single-screw extruder. The innovation was to directly process the cooked low-moisture extrudate to a couscous product by drying and milling to the appropriate particle size (ranging between 1 and 2 mm). Throughput for the traditional process as prepared for commercial sale is 50 kg per day, but with the same amount of labour, the extrusion process yields ~350 kg per day. A consumer sensory study held in Niamey (Niger) showed that the extruded millet couscous was comparable to traditional couscous, though this was dependent on selection of the proper millet variety. This novel extrusion process could stimulate small- to medium-scale manufacturing of couscous and couscous-type products in West Africa.     

Multimedia content recommendation in social networks using mood tags and synonyms

Multimedia Systems - The preferences of Web information purchasers are changing. Cost-effectiveness (i.e., an emphasis on performance with respect to price) is becoming less regarded than...     

A Two-Dimensional Numerical Analysis for Thermal Performance of an Intermittently Operated Radiant Floor Heating System in a Transient External Climatic Condition

Abstract

Building thermal inertia and operation control strategies have impacted on the thermal performance of a radiant floor heating system. This study conducts a two-dimensional numerical analysis of an intermittently operated radiant floor heating system using the Re-Normalization Group model with Discrete Ordinates Radiation model. A detailed numerical simulation setups and various analyses are provided, including grid independency analysis, initial condition, time step sizes and external boundary conditions. Three different weekend day intermittent operation strategies are investigated. The results showed that Case 3 designed with pre-heating of 20?h has better performance compared to Case 1 designed with pre-heating of 8?h and Case 2 designed with pre-heating of 14?h. The average indoor air temperature differences of approximate 2.1, 1.6 and 1.2 K are observed for Case 1, Case 2 and Case 3, respectively, when comparing two-time slot at 8:00am on Friday morning and Monday morning. This significantly highlights the effect of thermal inertia and the potential of energy saving due to the utilization of intermittent operation. Therefore, the current study presents numerical simulation potential in evaluating the radiant floor heating effects on indoor thermal environment, taking into account building thermal inertia and transient external climatic conditions.     

Effect of Initial Grain Size on Friction Stir Weldability for Rolled and Cast CoCrFeMnNi High-Entropy Alloys

Metals and Materials International - This study investigated the influence of the initial grain size on the plastic deformation and tunnel defects that occurred from friction stir welding of...     

Microscale Patterning of Mesoscopic PZN-PT Single Crystal Films by Crystal ion Slicing and Laser-Induced Etching

Advances in the fabrication of solid-solution single crystal relaxor ferroelectrics have made it possible to produce highly efficient piezoelectric crystals, and have attracted renewed interest in the use of these crystals for a new generation of piezoelectric transducers, actuators and sensors. Of particular interest is their incorporation into micro-electromechanical systems (MEMS). In this paper we report on the laser-induced wet chemical etching of lead zinc niobate-lead titanate (PZN-PT) in hydrochloric acid (HCl). Argon-ion laser radiation at power levels up to 4 W is focused to a spot diameter of about 15μm and results in the chemical etching of grooves at patterning speeds up to 5μm/sec. Crystal ion slicing, an ion-implant-based film separation technique, is used in combination with laser etching to form 5 to 10μm-thick patterned and freestanding films for incorporation into micro-electromechanical devices.     

Lead content of rice collected from various areas in the world

Rice samples consumed by local populations were collected between 1990 and 1995 in 17 areas in the world, mostly from Asia (10 areas), but also from 7 areas outside of Asia. In total, 1528 samples were obtained (about one half from Japan) and were analyzed for lead (Pb) by electrothermal atomic absorption spectrometry. When the Pb contents in rice samples were classified into 10 areas in Asia, the highest and the lowest geometric means (GMs) were for Indonesia (38 ng/g) and Australia (2 ng/g), respectively. Among 7 regions outside Asia, the GM was highest for Spain (58 ng/g) and the lowest for the USA. (3 ng/g). Moreover, inter-regional differences were significant, when more than 100 samples from one area were divided into 3-9 regions and GMs for regions were compared. There was a marked difference in Pb contents in rice by areas and regions in the world. Nevertheless, comparison by area of the present results with those reported in literature show that there has been no substantial reduction in Pb in rice in the past decade either in Japan or elsewhere in the world.     

Perspectives on Design and Innovation

A series of studies of top European and other firms has revealed patterns of design management associated with commercial success. Firms that invest resources and professional expertise in product and industrial design in traditional and new industries have been commercially more successful than firms that pay less attention to these aspects of design. As an industry matures there is a shift in emphasis from design associated with technological innovation, to designs supporting technical improvements, and then to supporting user needs, fashion and product variants. These issues are illustrated through the history of the evolution of the bicycle.     

A comparison of CCS tandem overload controls

In this paper we analyse issues associated with overloads in tandem switching systems in Common Channel Signalling (CCS) networks. In particular, we examine the need for, and effectiveness of, Automatic Congestion Control (ACC), a CCS mechanism which allows a congested switching system to inform adjacent CCS nodes of its level of overload, and subsequently controls the rate at which traffic is sent to the congested node. We demonstrate the critical need for end-offices and tandem switching systems to implement some form of ACC if network performance is to be maintained during congestion, especially in tandem exchanges. In addition, we find that the presently defined ACC should be expanded to allow more levels of congestion to be reported to adjacent nodes, so that a more effective, finer grained control is produced.