Interferometric monitoring of satellite longitudes

This paper proposes a technique for monitoring the longitudinal motion of geosynchronous satellites. A two‐antenna interferometer is used, with the baseline orientation adjusted to a particular horizontal azimuth. The interferometer then becomes insensitive to the north–south motion of the satellite, and this enables direct measurement of the satellite's longitudinal motion. Longitudes are monitored continuously, with no delay when orbital manoeuvres occur. The proposed technique is particularly useful when two or more satellites are operating in close proximity and their longitudes must be precisely monitored for safety control. Copyright © 2005 John Wiley & Sons, Ltd.     

Design of one-dimensional ferromagnet based on polyacetylene chain

As a model for organic ferromagnetism in a one-dimensional system, substituted polyacetylenes are re-considered on the basis of the molecular orbital (MO) and the crystal orbital (CO) methods. The semiempirical MO calculations with configuration interaction for the dimer model show that the exchange interaction on poly[(4-oxyphenyl)acetylene] (1) is negative in spite of Ovchinnikov's prediction, due to the direct interaction between the adjacent pendant spins. On the other hand, it is shown that a polyacetylene chain with phenoxy radicals as pendants on every other active site can become a one-dimensional feromagnet. Moreover, the CO calculations by means of the unrestricted Hartree-Fock method give a theoretical background for the realization of a ground state with macroscopic spin alignment on the improved model chain.     

Isothermal interphase diffusion with consecutive reactions

For multi-step heterogeneous consecutive reactions affected entirely by interphase diffusion under isothermal condition, the equations for the effectiveness factors, the surface concentrations and the point yields were derived in terms of the Damkoehler numbers or the measurables from the mass balances set up on the assumption that the mass-transfer rate balances the surface-reaction rate at steady state. From the analyses of the equations derived, the effectiveness factors for the intermediate steps and the surface concentrations of intermediates were understood to be enhanced by the measurables inclusive of the concentrations and the mass-transfer coefficients. Then the effect of the concentrations was concluded to be most significant. The effects of these measurables to the effectiveness factors and the surface concentrations were qualitatively discussed for simple consecutive reactions and also for additive consecutive reactions. Especially, as for two-step additive consecutive reactions, the effects of measurables η Da and the concentrations to the effectiveness factors were examined with graphical presentations. Finally, the brief discussion of the dependency of the Damkoehler number upon reaction time and the effect of the Renolds number and diffusivity to the extent of the mass-transfer resistance were presented.     

Preparation of spinel-type ferrite thin films by the dip-coating process and their magnetic properties

Films of spinel-type ferrite, MFe₂O₄ (M=Ni, Co, Mg, Li_0.5Fe_0.5) have been prepared by a dip-coating method from the sol-gel process. Ferric nitrate, nickel nitrate, cobalt nitrate and lithium nitrate were used as raw materials, and glycerol and formamide were used as solvents. A film was prepared by dipping a silica glass plate. The spinel-type ferrite was obtained by heat-treatment at 700–900°C for 2 h in air. The film thickness was about 0.8 m. The saturation magnetization, _r, of the film and powder with composition 50NiO·50Fe₂O₃ was 196 emu cm^–3 and 29.1 emu g^–1, respectively, and the coercive force,H _c, was 140 and 95 Oe, respectively, after heat-treatment at 800°C for 2 h. In particular, the films were shown to have a much largerH _c than the powder. The grain growth of spinel ferrite may be subject to restriction because it is in progress above an amorphous base-plate. The crystals are therefore aligned with the base-plate and have uniaxial anisotropy.     

Hydrolysis of human horny cells by alkaline protease: Morphological observation of the process

The interaction of highly purified alkaline protease fromBacillus sp. KSM-K16 with the horny cells of human skin contained in skin grime was directly visualized by electron microscopy. It became clear that the protease first penetrates the horny cells and then adsorbs, mainly onto the internal structure of the cells at the initial stage of hydrolysis, and directly hydrolyzes the keratin filaments, though the marginal band surrounding them retains its original shape. Then, hydrolysate produced from the keratin filaments flows out of the cell, and early in the hydrolysis process keratin filaments decrease and then disappear, leaving a marginal band, i.e., the cell turns to a hollow state. As a result, the remaining marginal band loses support from inside the cell, thus promoting cleavage and dispersion. Until this stage in the protease reaction, the remarkable liberation of hydrolysis products as water-soluble protein does not occur.     

N，O，O′─三（对甲苯磺酰基）双（2─羟乙基）胺的合成

二乙醇胺和对甲苯磺酰氯在三乙胺存在下，反应生成Ｎ，０，Ｏ′－三（对甲苯磺酰基）双（２－羟乙基）胺，产率９３％。从反应混合物中分离得副产物Ｎ，Ｏ－二（对甲苯磺酰基）双（２－羟乙基）胺。     

Inertial effects on cylindrical particle migration in linear shear flow near a wall

Micro-/nanoparticle-based systems are regarded as one of the possible candidates due to the engineerability and multifunctionality to maximize the accumulation of the nano-/microparticle-based drug delivery system on the target. Recent advances in nanotechnology enable the fabrication of diverse particle shapes from simple spherical particles to more complex shapes. The particle dynamics in blood flow and endocytosis characteristics of non-spherical particles change as the non-sphericity effect increases. We used a numerical approach to investigate the particle dynamics in linear shear flow near a wall. We examined the dynamics of slender cylindrical particles with aspect ratio γ = 5.0 in terms of particle trajectory, velocity, and force variation for different Stokes numbers over time. We identified the rotating inertia of particle near a wall as the source of inertial migration toward the wall. The drift velocity of slender cylindrical particles is comparable to that of discoidal particles. We discuss the possibilities and limitations of using slender cylindrical particles as a drug delivery system.     

Microalgae-Based Biohybrid Microrobot for Accelerated Diabetic Wound Healing

A variety of wound healing platforms have been proposed to alleviate the hypoxic condition and/or to modulate the immune responses for the treatment of chronic wounds in diabetes. However, these platforms with the passive diffusion of therapeutic agents through the blood clot result in the relatively low delivery efficiency into the deep wound site. Here, a microalgae-based biohybrid microrobot for accelerated diabetic wound healing is developed. The biohybrid microrobot autonomously moves at velocity of 33.3 µm s⁻¹ and generates oxygen for the alleviation of hypoxic condition. In addition, the microrobot efficiently bound with inflammatory chemokines of interleukin-8 (IL-8) and monocyte chemoattractant protein-1 (MCP-1) for modulating the immune responses. The enhanced penetration of microrobot is corroborated by measuring fibrin clots in biomimetic wound using microfluidic devices and the enhanced retention of microrobot is confirmed in the real wounded mouse skin tissue. After deposition on the chronic wound in diabetic mice without wound dressing, the wounds treated with microrobots are completely healed after 9 days with the significant decrease of inflammatory cytokines below 31% of the control level and the upregulated angiogenesis above 20 times of CD31⁺ cells. These results confirm the feasibility of microrobots as a next-generation platform for diabetic wound healing.     

Modified atmosphere packaging of fresh produce using microporous earthenware material

Microporous earthenware sheets of 5.5–5.6mm thickness were fabricated with or without a glazing treatment by passing through a sequential firing procedure in a furnace. Their microstructure and gas permeability against oxygen and carbon dioxide were measured and examined for their usability in modified atmosphere packaging of fresh produce. Compared with plastic packaging materials, earthenware sheets with a high proportion of micropores had very high gas permeability and gave CO₂:O₂ permeability ratios close to 1. Glazing treatment smoothed the surface by clogging the pores on the surface and significantly decreased gas permeability, without affecting the internal microstructure of the earthenware. When the earthenware sheet was combined with a plastic box and used in packaging for strawberries and enoki mushrooms at 5°C, its unique permeability properties developed a modified atmosphere that was beneficial for preserving the quality of the produce. Changes in the earthenware's permeability characteristics due to moisture adsorption and condensation need to be resolved so that the dynamic changes occurring in package atmosphere over time can be better understood. Copyright © 2006 John Wiley & Sons, Ltd.