Methodological Challenges in Union Commitment Studies.

Methodological problems in studies of union commitment were identified and illustrated with data from 4,641 members and 479 stewards in 297 local teachers' unions. Using a 20-item union commitment scale, results confirmed the existence of 3 substantive factors and 1 method factor at the individual level of analysis: loyalty to the union, responsibility to the union, willingness to work for the union, and a factor of negatively worded items. Tests of measurement invariance showed that the scale captured commitment for rank-and-file members but not for union stewards. The authors also found partial measurement invariance between long-time and newer members and full measurement invariance between men and women. Finally, the authors found that violation of the statistical assumption of independence reduced model fit when individual commitment scores were analyzed without attention to the hierarchical nature of the data. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Maximum power density for an endoreversible carnot heat engine

An analysis using maximum power-density criteria has been carried out for an endoreversible Carnot heat engine. The results have been compared with known results on maximum power analysis. The design parameters at maximum power density lead to smaller and more efficient endoreversible Carnot heat engines than those working at maximum power output.     

The statistical modeling of surface roughness in high-speed flat end milling

Surface roughness is one of the most important requirements in machining process. The surface roughness value is a result of the tool wear. When tool wear increase, the surface roughness also increases. The determination of the sufficient cutting parameters is a very important process obtained by means of both minimum surface roughness values and long tool life. The statistical models were developed to predict the surface roughness.This paper presents the development of a statistical model for surface roughness estimation in a high-speed flat end milling process under wet cutting conditions, using machining variables such as spindle speed, feed rate, depth of cut, and step over. First- and second-order models were developed using experimental results of a rotatable central composite design, and assessed by means of various statistical tests. The highest coefficient of correlation (R_adj²) (88%) was obtained with a 10-parameter second-order model. Meanwhile, a time trend was observed in residual values between model predictions and experimental data, reflecting the probable effect of the tool wear on surface roughness. Thus, in order to enhance the estimation capability of the model, another independent variable was included into the model to account for the effect of the tool wear, and the total operating time of the tool was selected as the most suitable variable for this purpose. By inserting this new variable as a linear term into the model, R_adj² was increased to 94% and a good fit was observed between the model predictions and supplementary experimental data.In this study, it was observed that, the order of significance of the main variables is as X₅>X₃>X₄>X₁>X₂ (total machining time, depth of cut, step over, spindle speed and feed rate, respectively).     

Degradation of 4-chloro-2-methylphenol in aqueous solution by electro-Fenton and photoelectro-Fenton processes

Degradation of 4-chloro-2-methylphenol (PCOC), a refractory toxic chemical emitted to the environment from the industrial production of phenoxy herbicides was studied in aqueous solution. Electro-Fenton and photoelectro-Fenton processes were used as the degradation methods. H₂O₂, produced by the reduction of oxygen at carbon cathode reacted with dissolved metal ions to form hydroxyl radicals, which in turn reacted with PCOC sequentially to degrade the aromatic ring. The effects of using different [Fe²⁺]/[PCOC]₀ and the effect of replacing Fe²⁺ by Mn²⁺ ion have been examined. It was found that degradation rate was increased with increasing [Fe²⁺]/[PCOC]₀ ratio from 2 to 4. However, the total charge utilized during the treatment was also increased. The efficiency of PCOC degradation was observed to be higher when Mn²⁺ was used as the catalyst. The mineralization of aqueous solutions of PCOC, withdrawn from the reactor at certain time interval, has been followed by total organic carbon (TOC) decay and dechlorination. A fast and complete degradation of the aromatic ring was achieved in photoelectro-Fenton system. 41.7% TOC decay and complete dechlorination were observed by consuming only 141.4 C electrical charge during a 300 min photoelectron-Fenton treatment. In the case of electro-Fenton system, 280.7 C electrical charge was consumed during 450 min of electrolysis to attain a similar degradation of PCOC. 14.9% TOC removal and 89.3% dechlorination have been obtained in this system under the applied conditions.     

Antibody purification by concanavalin A affinity chromatography

Concanavalin A (Con A) immobilized poly(2‐hydroxyethyl methacrylate) (PHEMA) beads in a spherical form (100–150 μm in diameter) were used for the affinity chromatography purification of human immunoglobulin G (IgG) from aqueous solutions and human plasma. PHEMA adsorbents were prepared by suspension polymerization. Bioligand Con A was then immobilized by covalent binding onto PHEMA beads. The maximum IgG adsorption on the PHEMA/Con A beads was observed at pH 6.0. The nonspecific IgG adsorption onto the plain PHEMA adsorbents was very low (ca. 0.17 mg/g). Higher adsorption values (up to 54.3 mg/g) were obtained when the PHEMA/Con A beads were used from aqueous solutions. A higher adsorption capacity was observed for human plasma (up to 69.4 mg/g) with a purity of 82.5%. The adsorption capacities of other blood proteins were 2.0 mg/g for fibrinogen and 4.2 mg/g for albumin. The total protein adsorption was determined to be 76.0 mg/g. IgG molecules could be repeatedly adsorbed and desorbed with the PHEMA/Con A beads without noticeable loss in the IgG adsorption capacity. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1202–1208, 2005     

Fair referee assignments for professional football leagues

Assignment of referees to football games is an important problem faced in professional football leagues. Despite its importance, the problem has received limited academic attention. This paper presents a model and analysis of the problem for fair referee assignments, and develops a constructive heuristic and a local search procedure for its solution. Results from an extensive computational study show that the methods are effective in solving the problem in a second of computation time and yielding an excellent solution quality.     

Adapting application execution in CMPs using helper threads

In parallel to the changes in both the architecture domain–the move toward chip multiprocessors (CMPs)–and the application domain–the move toward increasingly data-intensive workloads–issues such as performance, energy efficiency and CPU availability are becoming increasingly critical. The CPU availability can change dynamically due to several reasons such as thermal overload, increase in transient errors, or operating system scheduling. An important question in this context is how to adapt, in a CMP, the execution of a given application to CPU availability change at runtime. Our paper studies this problem, targeting the energy-delay product (EDP) as the main metric to optimize. We first discuss that, in adapting the application execution to the varying CPU availability, one needs to consider the number of CPUs to use, the number of application threads to accommodate and the voltage/frequency levels to employ (if the CMP has this capability). We then propose to use helper threads to adapt the application execution to CPU availability change in general with the goal of minimizing the EDP. The helper thread runs parallel to the application execution threads and tries to determine the ideal number of CPUs, threads and voltage/frequency levels to employ at any given point in execution. We illustrate this idea using four applications (Fast Fourier Transform, MultiGrid, LU decomposition and Conjugate Gradient) under different execution scenarios. The results collected through our experiments are very promising and indicate that significant EDP reductions are possible using helper threads. For example, we achieved up to 66.3%, 83.3%, 91.2%, and 94.2% savings in EDP when adjusting all the parameters properly in applications FFT, MG, LU, and CG, respectively. We also discuss how our approach can be extended to address multi-programmed workloads.