Breakdown characteristics of oil and paper insulation for a very fast transient voltage

This paper describes the dielectric breakdown characteristics of oil and oil‐impregnated paper for very fast transient (VFT) voltages. Blumlein circuits generate VFT voltages of 60 and 300 ns in a pulse width that simulates disconnecting switching surges in gas‐insulated switch gears. We measured the breakdown voltages of needle‐to‐plane, plane‐to‐plane oil gaps and several pieces of paper between plane electrodes for VFT and lightning impulse voltages. The measured data were formulated in V‐t characteristics and Weibull probability distributions. The inclination n of V‐t characteristics of insulating paper is 150, which is less than n = 13.7 of the plane‐to‐plane oil gap in the VFT time range. The shape parameters of Weibull distribution obtained in this study show that the scattering of breakdown voltages of paper is much less than that of oil. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(4): 16–24, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10043     

Stabilization of bioethanol recovery with silicone rubber‐coated ethanol‐permselective silicalite membranes by controlling the pH of acidic feed solution

In order to produce highly concentrated bioethanol by pervaporation using an ethanol‐permselective silicalite membrane, techniques to suppress adsorption of succinic acid, which is a chief by‐product of ethanol fermentation and causes the deterioration in pervaporation performance, onto the silicalite crystals was investigated. The amount adsorbed increased as the pH of the aqueous succinic acid solution decreased. The pervaporation performance also decreased with decreasing pH when the ternary mixtures of ethanol/water/succinic acid were separated. Using silicalite membranes individually coated with two types of silicone rubber, pervaporation performance was significantly improved in the pH range of 5 to 7, when compared with that of non‐coated silicalite membranes in ternary mixtures of ethanol/water/succinic acid. Moreover, when using a silicalite membrane double‐coated with the two types of silicone rubber, pervaporation performance was stabilized at lower pH values. In the separation of bioethanol by pervaporation using the double‐coated silicalite membrane, removal of accumulated substances having an ultraviolet absorption maximum at approximately 260 nm from the fermentation broth proved to be vital for efficient pervaporation. Copyright © 2005 Society of Chemical Industry     

Polarity control of GaN epilayers grown on ZnO templates

We report the successful growth of Ga-polar GaN epilayers on O-polar ZnO templates pre-deposited on c-sapphire. Prior to GaN growth, NH₃ is exposed onto the ZnO template. The polarity of the GaN layers is confirmed by etching of the surface and by conversion beam electron diffraction (CBED), while the O-polar ZnO is confirmed by CBED. It is suggested that the NH₃ pre-exposure helps form a Zn₃N₂ layer, which possesses inversion symmetry and inverts the crystal from anion polar to cation polar.     

Accelerated neutrophil apoptosis in mice lacking A1-a, a subtype of the bcl-2-related A1 gene

To elucidate the role of A1, a new member of the Bcl-2 family of apoptosis regulators active in hematopoietic cell apoptosis, we established mice lacking A1-a, a subtype of the A1 gene in mice (A1-a-/- mice). Spontaneous apoptosis of peripheral blood neutrophils of A1-a-/- mice was enhanced compared with that of either wild-type mice or heterozygous mutants (A1-a+/- mice). Neutrophil apoptosis inhibition induced by lipopolysaccharide treatment in vitro or transendothelial migration in vivo observed in wild-type mice was abolished in both A1-a-/- and A1-a+/- animals. On the other hand, the extent of tumor necrosis factor alpha-induced acceleration of neutrophil apoptosis did not differ among A1-a-/-, A1-a+/-, and wild-type mice. The descending order of A1 mRNA expression was wild-type, A1-a+/-, and A1-a-/-. Taken together, these results suggest that A1 is involved in inhibition of certain types of neutrophil apoptosis.     

New polylactide/layered silicate nanocomposites. 5. Designing of materials with desired properties

Understanding the structure/property relationship in polymer/layered silicate nanocomposites is of great importance in designing materials with desired properties. In order to understand these relations, a series of polylactide (PLA)/organically modified layered silicate (OMLS) nanocomposites have been prepared using a simple melt extrusion technique. Four different types of OMLS have been used for the preparation of nanocomposites, three were modified with functionalized ammonium salts while fourth one was a phosphonium salt modified OMLS. The structure of the nanocomposites in the nanometer scale was characterized by using wide-angle X-ray diffraction and transmission electron microscopic observations. Using four different types of layered silicates modified with four different types of surfactants, the effect of OMLS in nanocomposites was investigated by focusing on four major aspects: structural analysis, thermal properties and spherulite morphology, materials properties, and biodegradability. Finally, we draw conclusions about the structure/property relationship in the case of PLA/OMLS nanocomposites.     

Structural development in cycloolefin copolymers under uniaxial elongational flow

Development of structures in new cycloolefin copolymers (COCs) of ethylene–norbornene (E–NB) and ethylene–tetracyclododecene (E–TD) of different NB/TD compositions were investigated under uniaxial elongational flow. For E–NB copolymer, which has multiblock sequences, a shoulder in WAXD at 0.76 nm was evident besides its amorphous halo, and the relative intensity of the peak increased with increasing comonomer content (NB). The appearance of a new peak for E–TD copolymer, and a relatively higher intense peak for E–NB copolymer at the same position of 0.76 nm, indicated that local ordering of the segments occurred when the COC was subjected to uniaxial flow. A lower comonomer composition of elongated COC, at a constant Hencky strain rate, exhibited two T_g values, whereas a higher composition showed a single T_g. Both local ordering and segmentization occurred in low comonomer content COCs but only local ordering occurred in higher comonomer content COCs. Both the shear viscosity and roll processing experiments exhibited similar phenomena of segregation. A model is proposed to illustrate the structure of COC after uniaxial elongation/deformation. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3421–3427, 2004     

Multi-step precipitation separation system using mixture of thermosensitive polymers

Summary Multi-step precipitation separation system was developed by using aqueous mixtures of some thermosensitive polymers. The following three polymers were used here; poly(N-n-propylacrylamide), poly(N-isopropylacrylamide), and poly(N-isopropylmethacrylamide). A mixture of the three polymers showed three endothermic peaks, and the peak top temperatures were almost consistent with that of the each polymer solution. The polymers were purified by thermal precipitation to obtain fractions which can respond in narrow temperature ranges prior to use. In the case of the precipitation separation of two polymers mixtures, purities of the obtained precipitate and supernatant fractions became high comparing with the case in which the unpurified polymers were used. Parts of the polymers which were not the precipitation targets were also precipitated by the separation procedures. This was caused not only by insolubilization of the non-targeted polymers due to their phase transitions but also by their non-specific entanglement with the targeted polymers. The purities of the fractions also improved when the difference of the phase transition temperature between two polymers was large enough to avoid the coprecipitation. In the case of the precipitation separation of mixtures of the three polymers, purities of each fraction also improved when the purified polymers were used.     

Rapid Quenching Technique Using Thermal-Image Furnace for Glass Preparation

A new technique combining a thermal-image furnace and a twin roller is described for quenching the melt to form glass. The technique was applied to the simple system Li₂O-SiO₂, since its fundamental parameters in the estimation of critical cooling rate are available. Glass flakes were obtained in the composition Li₄SiO₄, for which a very large critical cooling rate (∼10⁹ K·s⁻¹) was needed for glass formation.     

Reactive processing of polymer blends: Analysis of the change in morphological and interfacial parameters with processing

The change in morphology and interface quantities have been analyzed for an immiscible polymer blend during reactive processing. A model polymer/polymer combination, hydroxy-terminated poly(ε-caprolactone)/liquid rubber with α, ω-carboxy groups, was employed. The blend was subjected to light scattering measurements, ellipsometry, and gel permeation chromatography (GPC). Size reduction of the dispersed phase during processing was followed by a systematic decrease in the correlation distance ζ and an increase in the specific interfacial area Ssp, both by the Debye-Bueche plot of light scattering profiles. Also observed was the time variation of the volume fraction of interface V_λ estimated as a product of the Ssp and the interfacial thickness by ellipsometry. The changes in ζ, Ssp, and V_λ with processing were accelerated when a coupling agent,γ-aminopropyltriethoxysilane (APS), was added. The amount of block copolymer formed in-situ in the APS-loaded system was estimated by GPC with RI and UV detectors. For the size reduction kinetics in both APS-loaded and -unloaded systems, Rittinger's law was found to be applicable.     

Structure and properties of nanocomposites based on poly(butylene succinate) and organically modified montmorillonite

Poly(butylene succinate) and organically modified montmorillonite nanocomposites with there different compositions were prepared via melt blending in a twin‐screw extruder. The structure of the nanocomposites was studied with X‐ray diffraction and transmission electron microscopy, which revealed the formation of intercalated nanocomposites, regardless of the silicate loading. Dynamic mechanical analysis revealed a substantial increase in the storage modulus of the nanocomposites over the entire temperature range investigated. The tensile property measurements showed a relative increase in the stiffness with a simultaneous decrease in the yield strength in comparison with that of neat poly(butylene succinate). The oxygen gas barrier property of neat poly(butylene succinate) improved after nanocomposite preparation with organically modified montmorillonite. The effect of the layered‐silicate loading on the melt‐state linear viscoelastic behavior of the intercalated nanocomposites was also investigated. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 777–785, 2006